Titan 640 Skid Owner's Manual page 7

Main Screen
The Main Screen is the default screen
for the control system at sprayer startup.
Pressing the #2 key switches between PSI and MPa units of measure.
Press the #1 key to scroll through the remaining menu screens.
Gallons Pumped Screen
The Gallons Pumped screen shows the
total number of gallons or liters sprayed
by the sprayer.
To select the Volume Pumped screen,
press the #4 key.
Job Gallons Screen
The Job Gallons screen allows the user
to reset a gallon counter to track usage
on specific jobs.
To select the Job Volume screen, press
the #4 key.
unit Serial # Screen
The Unit Serial # screen shows the
sprayers serial number.
To select the Unit Serial # screen, press
the #4 key.
Timers Screen
The Timers screen shows the total time
the sprayer has been turned on as well
as the total time the sprayer has been running (pumping).
To select the Timers screen, press the
#4 key.
Job Timers Screen
The Job Timers screen allows the user
to reset the "ON TIME" and "RUN TIME"
to track time on specific jobs.
To select the Job TImers screen, press
the #4 key. The screen will toggle
between the timers and a screen that allows the user to reset the
timers.
Service Time Screen
The Service Time screen allows the user
to set a service time interval (in hours).
Below the set time, the screens shows the current amount of
hours on the sprayer. To select the Service Timer screen, press
the #4 key.
The screen will toggle between the
service hours and a screen that allows
the user to change the service time interval.
When the service time interval is set and met by the run hours,
the display will toggle between the "Main screen" and a "Service
Required" screen at sprayer startup. To stop the toggling, scroll
to the "Service Time" screen and either set a new service time
interval or set the service time to "0".
Pressure Screen
The Pressure screen allows the user to
see the current set point pressure as
well as the actual working pressure.
To select the Pressure screen, press
the #4 key. This screen is also the Main
Screen.
© Titan Tool Inc. All rights reserved.
Security code Screen
SET PSI 3000
The Security Code screen allows the
ACTUAL PSI 2950
user to set a four digit security code
to prevent unauthorized use of the sprayer. If a security code
has been set, the control system display will ask for the code at
startup. If the correct code is entered, the display will show the
Main Screen and the sprayer will operate. If the wrong code is
GALLONS PUMPED
entered, the display will continue to ask for the correct code and
MENU-1 SELECT-4
the sprayer will be disabled. To set or change the security code,
press the #2 key.
GALLONS XXXXXX
PRESS 1 FOR MENU
JOB GALLONS
MENU-1 SELECT-4
Enter the old security code number to
JOB GALLONS XXXX
access the screen that allows the code
RESET-3 MENU-1
change. If the wrong code is entered, the display will continue to
ask for the correct code and the security code cannot be changed.
Enter the new security code. Once the
UNIT SERIAL #
new code is entered, the display will
MENU-1 SELECT-4
automatically ask that the new code be re-entered for verification.
SER # XXXXXXXXXX
If the same new code is re-entered, the display will confirm that
PRESS 1 FOR MENU
the new code has been accepted and return to the Main Screen.
If the new code is re-entered incorrectly, the display will return to
the "Enter New Code Number" screen and the process will repeat.
TIMERS
MENU-1 SELECT-4
ON TIME XXXXX:XX
RUN TIME XXXX:XX
Prime Screen
JOB TIMERS
MENU-1 SELECT-4
The Prime screen appears when the
pressure control knob is set at the "MIN"
setting.
ON TIME XXXXX:XX
RUN TIME XXXX:XX
Rapid clean Screen
The Rapid Clean screen appears when
the pressure control knob is set at the
RAPID CLEAN position and the PRIME/SPRAY valve is in the
PRIME position.
SERVICE TIME
MENU-1 SELECT-4
SERVICE @ XXXHR
RUN HOURS XX
PRESSURE
MENU-1 SELECT-4
SET PSI 3000
ACTUAL PSI 2950
7
NOTE: If the sprayer is new, no security code is set and
the Main Screen will appear at startup. also,
when setting a security code for the first time,
the "Enter Old code Number" screen will not
appear.
NOTE: To inactivate the anti-Theft Digital Lockout
security function, enter "1111" at the "Enter New
code Number" screen (this is the default code
that leaves the sprayer unlocked). as a result,
the Main Screen will appear at sprayer startup.
NOTE: If there is no action at any menu screen for 30
seconds, the display will go back to the Main
Screen.
SECURITY CODE
MENU-1 CHANGE-2
ENTER OLD CODE
NUMBER
ENTER NEW CODE
NUMBER
PRIME
RAPID CLEAN
ACTUAL PSI XXXX
English