Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Net Optics 10/100BaseT Slim Tap
Summary of Contents for Net Optics 10/100BaseT Slim Tap
- Page 1 Installation Guide for 10/100BaseT Slim Tap Doc. PUBTPCUSLMU Rev.1, 12/06...
-
Page 3: Table Of Contents
Steps to Install the 10/100BaseT Slim Tap . . . . . . . . . . . . . . . . . - Page 4 PLEASE READ THESE LEGAL NOTICES CAREFULLY. By using a Net Optics Tap you agree to the terms and conditions of usage set forth by Net Optics, Inc . No licenses, express or implied, are granted with respect to any of the technology described in this manual .
-
Page 5: About This Guide
10/100 BaseT Slim Tap About This Guide This guide explains how to install the 10/100BaseT Slim Tap . Please read the Guide before attempting to install the 10/100BaseT Slim Tap . This guide cov- ers the following models: Model TP-CUSLM... - Page 6 . Only the connected computer can request information . Reliability For extra uptime protection, Net Optics 10/100BaseT Taps offer redundant power connections . Should the primary power source fail, the Tap automatically switches to the backup power source . Power LEDs on the front of the Tap indicate the current power source –...
-
Page 7: Key Features
Our technical support team is available from 8 am to 5 pm Pacific Time, Monday through Friday at +1 (408) 737-7777 and via email at ts- support@netoptics .com . FAQs are also available on Net Optics website at www .netoptics .com . -
Page 8: Steps To Install The 10/100Baset Slim Tap
RS232 connection . • Connect a monitoring device to the Slim Tap . Unpack and Inspect the Slim Tap Unpack the 10/100BaseT Slim Tap and check for damaged or missing parts . The Tap ships with the following: • 10/100BaseT Slim Tap •... -
Page 9: Product Diagrams
10/100 BaseT Slim Tap Product Diagrams Network A & B Alarm LEDs 10/100 Tap 10/100 Tap www.netoptics.com Reset Button Monitor A & B Power LEDs Digital Display Figure 2: TP-CUSLM Front Panel RS232 Port Power DC Power LEDs Figure 3: TP-CUSLM Rear Panel... -
Page 10: Connect The Slim Tap To The Network
10/100 BaseT Slim Tap Cabling Guidelines • If connecting to Switches or Hubs, use CAT5 RJ45 cross-over cabling . • If connecting to Routers or NICs, use CAT5 RJ45 straight-through cabling . Connect the Slim Tap to the Network If you are connecting to switches or hubs, use CAT5 RJ45 straight-through cabling .If you are connecting to routers or NICs, use CAT5 RJ45 straight- through cabling . -
Page 11: Connect Slim Tap Power
10/100 BaseT Slim Tap Connect the Slim Tap Power 1 . Supply power to the Tap using the two redundant power supplies included with the unit . 2 . Verify that the appropriate Power LED(s) are illuminated . 3 . Turn off power to the unit . Figure 6: Connecting dual power supplies The second power supply is available to support the flow of traffic to the monitoring device in the event that the first power supply becomes... - Page 12 10/100 BaseT Slim Tap To computer with terminal emulation software Figure 7: RS232 DB-9 connecting to computer 2 . Launch the terminal emulation and set communication parameters to: 19200 baud 8 data bits No parity 1 stop bit No flow control 3 .
- Page 13 10/100 BaseT Slim Tap You now have seven options, listed in the chart below: (The following commands are not case sensitive) Press this: To accomplish this: A on the keyboard Display Port A Utilization B on the keyboard Display Port B Utilization C on the keyboard Display Link Speed of Ports A and B D on the keyboard...
- Page 14 10/100 BaseT Slim Tap 7 . Enter d to display network port alarm status (see below) . 8 . Enter e to configure Port A alarm threshold (see below). 9 . Enter f to configure Port B alarm threshold (see below). 10 .
-
Page 15: Connect The Monitoring Device To The Slim Tap
10/100 BaseT Slim Tap 11 . Press i to reset network port B alarm (see below) . 12 . To reset both network ports simultaneously press the reset button on the front of the unit . NOTE: _______________________________________________________________ If auto-negotiation is turned off on one of the network device, then it must also be turned off on the other network device. -
Page 16: Specifications
Copper Cable Type: 22-24 AWG unshielded twisted pair cable, CAT5 Link Distance Supported: 100 meters Connectors (2) RJ45, 8-pin connectors (monitor ports) (2) RJ45, 8-pin connectors (network ports) Certifications • 10/100BaseT Slim Tap is compliant with IEEE 802 .3 • Fully RoHS compliant... -
Page 17: Limitations On Warranty And Liability
. Net Optics, Inc . warrants this Tap to be in good working order for a period of ONE YEAR from the date of purchase from Net Optics or an authorized Net Optics reseller . - Page 18 10/100 BaseT Slim Tap Notes:...
- Page 20 © 2007 by Net Optics, Inc . All Rights Reserved .