Parts And Functions; Remote Controller - Haier E Series Service Manual

Parts and Functions

Indoor Unit
1
2
3
7
5
1 1
Inlet
2 2
Inlet grille
3 3
Air Purifying Filter (inside)
4 5
Outlet
Actual inlet grille may vary from the one shown in the
manual according to the product purchased
8
Display board
2 3
1
1
Signal receiver hole
2
HEALTH display
(If the unit which you purchased
has healthy function,follow it.
If not,please ignore.)
3
TIMER OFF display
TIMER ON display,SLEEP display
4
Ambient temp.display
Outdoor Unit
Loading of the battery / Clock set
1
Remove the battery cover;
2
Load the batteries as illustrated.2 R-03
2
batteries, resetting key (cylinder);
3
1
Be sure that the loading is in line with the" + "/"-";
4
Load the battery,then put on the cover again.
3
Note:
The distance between the signal transmission head and the
receiver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change-over
wireless telephone is installed in the type fluorescent lamp or room,
the receiver is apt to be disturbed in receivingthe signals, so the
distance to the indoor unit should be shorter.
Full display or unclear display during operation indicates the
batteries have been used up.Please change batteries.
If the remote controller can't run normally during operation, please
remove the batteries and reload several minutes later.
Clock set
Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time.
Each press will increase or decrease
1min. If the button is kept pressed,time
will change quickly. After time setting is
confirmed,press SET,"AM "and "PM"
stop flashing while clock starts working.
Hint:
Remove the batteries in case unit won't be in usage for a long period.
If there are any display after taking-out, just need to press reset key
4 5
Horizontal flap
(adjust up and down air flow
Don't adjust it manually)
6 6
Vertical blade
(adjust left and right air flow)
7
Anion generator
(inside)
4 5 6
7
(When receiving the remote control signal,
display the set temperature and in the rest
time the room temperature is displayed and
this room temperature is only for reference.)
5
AUTO display
6
COOL display
7
Dry display
8
HEAT display
OUTLET
INLET
CONNECTING PIPING
AND ELECTRICAL WIRING
4 1 4
DRAIN HOSE
POWER/SOFT
24L/H A

Remote controller

4
5
6
8
8
1.CODE
Used to select CODE A or B with a press,A or B
will be displayed on LCD.
Please select A without special explanation.
2.RESET
When the remote controller appears abnormal,
use a sharp pointed article to press this button
to reset the remote controller normal.
3.LIGHT button
Control the lightening and extinguishing of
the indoor LED display board.
4. TIMER button
Used to select TIMER ON, TIMER OFF,
TIMER ON-OFF.
5. CLOCK button
Used to set correct time.
If the unit which you purchased has SWING LEFT/RIGHT function,follow it.If not,please ignore.
FRESH
1.CODE
Used to select CODE A or B with a press,
A or B will be displayed on LCD.
Please select A without special explanation.
2.RESET
When the remote controller appears abnormal,
use a sharp pointed article to press this button
to reset the remote controller normal.
3.LIGHT button
Control the lightening and extinguishing of
the indoor LED display board.
4. TIMER button
Used to select
TIMER ON, TIMER OFF,TIMER ON-OFF.
5. CLOCK button
Used to set correct time.
6. SLEEP button
Used to select sleep mode.
7. MODE button
AUTO COOL DRY
NOTE:
Cooling only unit do not have disp l ays and functions related with heating
If the unit which you purchased has healthy function,follow it.If not,please ignore.
24
: http://splitoff.ru/tehn-doc.html
6. HEALTH button
Used to set healthy operation.
7. MODE button
19
8. HOUR button
Used to set clock and timer setting.
9. SWING button
Used to select up or down air sending direction.
10 . ON/OFF button
Used for unit start and stop.
11. TIMER ON display
12. FAN SPEED display
LOW MED
13. LOCK display
14. SWING UP/DOWN display
15. SLEEP display
16. HEALTH display
17. Operation mode display
Operation mode
28
POWER/SOFT Remote controller
Display board
18.Signal sending display
30
19. POWER/SOFT display
20. Left/right air flow display
21. TEMP display
Remote controller: to display the TEMP. setting.
22. TIMER OFF display
23. CLOCK display
24. TEMP button
Used to select your desired temperature.
25. FAN button
Used to select fan speed: LOW,MED, HI, AUTO.
26. HEALTH AIRFLOW button
Used to set the health airflow mode.
27. SLEEP button
Used to select sleep mode.
28. SET button
Used to confirm timer and clock settings.
29. POWER/SOFT button
Use to set power/soft function.
30. LOCK
Used to lock buttons and LCD display. If pressed, the
other buttons will be disabled and the lock condition
display appears. Press it once again, lock will be
cancelled and lock condition display disappears.
8. HOUR button
Used to set clock and timer setting.
9.
HEALTH button
Used to set healthy function.
19
10. ON/OFF button
Used for unit start and stop.
11. TIMER ON display
12. FAN SPEED display
LOW MED
13. LOCK display
14. SWING UP/DOWN display
15. SLEEP display
16. HEALTH display
17. Operation mode display
28
Operation mode
Remote controller
POWER/SOFT
Display board
18.Signal sending display
19.POWER/SOFT display
20. Left/right air flow display
21. TEMP display
Remote controller: to display theTEMP. setting.
22. TIMER OFF display
23. CLOCK display
24. TEMP button
Used to select your desired temperature.
25. FAN button
Used to select fan speed: LOW,MED, HI, AUTO.
26. HEALTH AIRFLOW button
Used to set the health airflow mode.
27. SWING UP/DOWN button
Used to select up or down air sending direction.
28. SWING LEFT/RIGHT button
Used to select left/right air flow.
29 FRESH button
Use to set fresh air function.
(This function is unavailable on this models.)
30 SET button
Used to confirm timer and clock settings.
POWER/SOFT button
31.
Used to set power/soft function.
32. LOCK
Used to lock buttons and LCD display. If pressed, the
other buttons will be disabled and the lock condition
HEAT FAN
display appears. Press it once again, lock will be
canceled and lock condition display disappears.
AUTO COOL DRY FAN HEAT
HI AUTO
AUTO COOL DRY HEAT FAN
HI AUTO
AUTO COOL DRY HEAT FAN