Sony HCD-GN100D Service Manual page 2

HCD-GN90D/GN100D
QQ
3 7 63 1515 0
S VIDEO OUT
(4-pin/mini-DIN jack):
PHONES:
(stereo mini jack)
FRONT SPEAKER:
SUBWOOFER OUT:
(phono jack)
SURROUND SPEAKER:
CENTER SPEAKER:
Disc player section
System
Laser
Frequency response
Video color system format NTSC, PAL
(except Latin American models)
Tape deck section
Recording system
Frequency response
TE
Tuner section
L 13942296513
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
Antenna
Antenna terminals
Intermediate frequency
AM tuner section
Tuning range
Latin American models:
Saudi Arabian models:
Other models:
Antenna
Antenna terminals
Intermediate frequency
General
Power requirements
Australian model:
Mexican model:
Saudi Arabian models:
www
Other models:
.
Power consumption
MHC-GN100D
MHC-GN90D
2
http://www.xiaoyu163.com
Y: 1 Vp-p, unbalanced,
Sync negative
C: 0.286 Vp-p load
impedance 75 ohms
accepts headphones of
8 ohms or more
Use only the supplied speaker
Voltage 250 mV
impedance 1 kilohms
Use only the supplied speakers
Use only the supplied speaker
Compact disc and digital
audio and video system
Semiconductor laser
(DVD: λ = 650 nm,
CD: λ = 780 nm)
Emission duration: continuous
DVD (PCM 48 kHz):
2 Hz – 22 kHz (±1dB)
CD: 2 Hz – 20 kHz (±0.5 dB)
4-track 2-channel stereo
50 – 13,000 Hz (±3 dB),
using Sony TYPE I tape
87.5 – 108.0 MHz (50 kHz step)
FM lead antenna
75 ohm unbalanced
10.7 MHz
530 – 1,710 kHz
(with the interval set at 10 kHz)
531 – 1,710 kHz
(with the interval set at 9 kHz)
531– 1,602 kHz
(with the interval set at 9 kHz)
531 – 1,602 kHz
(with the interval set at 9 kHz)
530 – 1,710 kHz
(with the interval set at 10 kHz)
AM loop antenna
External antenna terminal
450 kHz
230 – 240 V AC, 50/60 Hz
127 V AC, 60 Hz
120 – 127 V, 220V or
230 – 240 V AC, 50/60 Hz
Adjustable with voltage selector.
120 V, 220 V or
x ao
y
230 – 240 V AC, 50/60 Hz
Adjustable with voltage selector
i
390 watts
275 watts
http://www.xiaoyu163.com
8
Dimensions (w/h/d) (Approx.)
HCD-GN100D/GN90D
Mass (Approx.)
HCD-GN100D
HCD-GN90D
Design and specifications are subject to change without notice.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
Q Q
3 6 7 1 3
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
u163
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
.
PUBLISHED BY SONY.
2 9 9 4 2 8
280 x 360 x 394.5 mm
16.1 kg
15.2 kg
This appliance is classified as
1 5 0 5 8 2 9 9 4
a CLASS 1 LASER product.
This label is located on the rear
exterior.
This following caution label is
located inside the apparatus.
m
co
9 9
2 8 9 9