Glow-worm 30ci Instructions For Use, Installation & Servicing page 9

NOTE: MULTIPLE ON OR OFF EVENTS MAY BE
PROGRAMMED, SEE EXAMPLE.
BEFORE PROCEEDING WITH SETTING THE TIME AND
PROGRAMMING THE UNIT, PRESS THE RESET KEY TO
CLEAR ALL DATA FROM THE MEMORY.
Selecting AM/PM or 24 Hour Time
After pressing reset, the display may show AM (below). The
numbered day symbols will be flashing on and off.
If the display does not show AM, it is in 24 hour time. To change
to AM/PM mode, press and hold the h key and press the
key once. AM will appear in display.
If display is in AM/PM mode and 24 hour time mode is desired,
press and hold the h key, press the
Setting the Time
IF THE h AND m KEYS ARE HELD DOWN LONGER THAN 2
SECONDS, THE NUMBERS WILL ADVANCE RAPIDLY.
Press and hold the key during the following:
(If British Summer Time is in effect, press
1. Press h to advance to the current hour
(while holding down the
2. Press m to advance to the current minute
(while holding down the
3. Press Day repeatedly to advance to current day
(while holding down the
Day Key Selections
Press Day Key Display Shows
0 times 1 2 3 4 5 6 7
1 time 1 2 3 4 5 6
2 times 1 2 3 4 5
3 times
4 times 1
5 times 2
6 times 3
7 times 4
8 times
9 times
10 times
NOTE: If the days are flashing, it indicates the day of the week
was not set when setting the time. The timer cannot be
programmed unless the day of the week is entered.
Manual GMT/BST Time Changeover
Each year, in the Spring, press
±
hour. In the Autumn, press
Supplied By www.heating spares.co Tel. 0161 620 6677
Programmer Instructions for Use
±
1h key once.
±
1h first)
key)
key)
key)
Days
Every Day
Mon.–Sat.
Mon.–Fri.
6 7 Sat. & Sun.
Monday
Tuesday
Wed.
Thursday
5 Friday
6 Saturday
7 Sunday
±
1h to advance the time an
1h to set back an hour.
Programming 24 Hour or 7 Day Schedules
It may be helpful to write out the programme schedules before
beginning.
THE CURRENT TIME OF DAY AND DAY OF WEEK MUST BE
SET PRIOR TO PROGRAMMING. SEE "SETTING THE TIME"
Event 1: ON at 7:00AM Monday through Saturday
±
Event 2: OFF at 5:00PM Monday through Friday
1h
Event 3: OFF at 7:00PM Saturday
Three events need to be entered.
Press Prog. key only once. Display shows :
Event 1 (ON at 7:00AM Monday through Saturday)
Press key once. ON symbol
Press h key to 07AM
Press m key once to 00
Press Day key once 1 2 3 4 5 6 is displayed
Press Prog. key to enter
Event 2 (OFF at 5:00PM Monday through Friday)
Press key twice. OFF symbol
Press h key to 05PM
Press m key once to 00
Press Day key two times 1 2 3 4 5 is displayed
Press Prog. key to enter
Event 3 (OFF at 7:00PM Saturday)
Press key twice. OFF symbol
Press h key to 07PM
Press m key once to 00
Press Day key 9 times until only 6 is displayed
Press Prog. key to enter
Press key to enter Run Mode
IF AN "ON" TIME WAS PROGRAMMED THAT IS EARLIER IN
THE DAY THAN THE CURRENT TIME, PRESS ONCE TO
TURN THE TIMER "ON". (IT DOES NOT "LOOK BACK" TO
DETERMINE IF IT SHOULD BE ON OR OFF AFTER
PROGRAMMING).
IF 24 HOUR TIME CONTROL (SAME SCHEDULE EVERY DAY
OF THE WEEK) IS DESIRED, IGNORE Day KEY.
If an ON or OFF symbol is not entered, the ON symbol will flash,
and programme will not be accepted.
9
Example
appears
appears
appears
4000123434-2