Hilti TE 50 Operating Instructions Manual
Hide thumbs
Also See for TE 50:
- User manual ,
- Original operating instructions (204 pages) ,
- Manual (150 pages)
Subscribe to Our Youtube Channel
Related Manuals for Hilti TE 50
Summary of Contents for Hilti TE 50
- Page 1 TE 50 / TE 50-AVR Operating instructions Mode d’emploi Manual de instrucciones Manual de instruções Printed: 08.07.2013 | Doc-Nr: PUB / 5130192 / 000 / 01...
- Page 2 This Product is Certified Ce produit est certifié Este producto esta certificado Este produto está certificado Printed: 08.07.2013 | Doc-Nr: PUB / 5130192 / 000 / 01...
- Page 3 Printed: 08.07.2013 | Doc-Nr: PUB / 5130192 / 000 / 01...
-
Page 4: Table Of Contents
In these operating instructions, the designation “the Always keep these operating instructions to- power tool” always refers to the TE 50 or TE 50-AVR gether with the power tool. combihammer. Ensure that the operating instructions are... -
Page 5: Description
Modification of the power tool or tampering with its parts is not permissible. To avoid the risk of injury, use only genuine Hilti accessories and insert tools. Observe the information printed in the operating instructions concerning operation, care and maintenance. - Page 6 (see section 9 “Troubleshooting”). 2.6 Lubrication Oil lubrication 2.7 Active vibration reduction (only TE 50‑AVR) The power tool is equipped with an AVR active vibration reduction system which reduces vibration significantly compared to power tools without active vibration reduction. 2.8 TPS theft protection system (optional) The power tool may be equipped with the TPS theft protection system as an option.
-
Page 7: Insert Tools, Accessories
∅ 6…35 mm (¼ to 1³/₈") Metal drill bits ∅ 6…13 mm (¼ to ½") 4 Technical data Right of technical changes reserved. Power tool TE 50 / TE 50‑AVR Rated voltage 120 V Rated current input 12.7 A Mains frequency 50…60 Hz... -
Page 8: Safety Instructions
Power tool TE 50 / TE 50‑AVR Percussion core bits ∅ 45…90 mm (1¾ to 3⁹⁄₁₆") Drilling dia. range in wood (solid) ∅ 6…35 mm (¼ to 1³/₈") Drilling dia. range in metal (solid) ∅ 6…13 mm (¼ to ½") - Page 9 Keep the grips dry, clean and free from oil and frequently for work on conductive materials grease. should be checked at regular intervals at a Hilti b) Breathing protection must be worn if the power Service Center. Under unfavorable circumstances,...
-
Page 10: Before Use
d) When working outdoors with an electric tool proved safety equipment, such as respiratory pro- tection appropriate for the type of dust generated, check to ensure that the tool is connected to the electric supply by way of a ground fault circuit and designed to filter out microscopic particles interrupter (GFCI) with a rating of max. - Page 11 7.1 Preparing for use CAUTION Improve the blood circulation in your fingers by re- CAUTION laxing your hands and exercising your fingers during Wear protective gloves when changing insert tools as breaks between working. the insert tools get hot during use. 7.2.1 TPS theft protection system (optional) 7.1.1 Adjusting the depth gauge 3 NOTE...
-
Page 12: Care And Maintenance
the power tool to run under no load until it reaches 7.2.4 Chiseling the minimum operating temperature. If necessary, repeat NOTE this procedure until the hammering mechanism begins to The chisel can be adjusted to 12 different positions operate. (in 30° increments). This ensures that flat chisels and shaped chisels can always be set to the optimum working Turn the function selector switch until it engages in position. -
Page 13: Troubleshooting
Blinking red light See section “Troubleshooting”. damaged or when the controls do not function faultlessly. 8.4 Maintenance If necessary, the power tool should be repaired by Hilti WARNING Service. Repairs to the electrical section of the power tool may be carried out only by trained electrical specialists. -
Page 14: Disposal
10 Disposal Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools or appliances for recycling. Please ask your Hilti customer service department or Hilti representative for further information. - Page 15 Tel.: +423 / 234 21 11 Fax:+423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 3254 | 1212 | 00-Pos. 3 | 1 Printed in Liechtenstein © 2012 Right of technical and programme changes reserved S. E. & O 383920 / A2 Printed: 08.07.2013 | Doc-Nr: PUB / 5130192 / 000 / 01...
Need help?
Do you have a question about the TE 50 and is the answer not in the manual?
Questions and answers