Hilti TE 50 Original Operating Instructions

Hilti TE 50 Original Operating Instructions

Hide thumbs Also See for TE 50:

Advertisement

TE 50
TE 50-AVR
English
Printed: 14.12.2018 | Doc-Nr: PUB / 5283568 / 000 / 03

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TE 50 and is the answer not in the manual?

Questions and answers

Summary of Contents for Hilti TE 50

  • Page 1 TE 50 TE 50-AVR English Printed: 14.12.2018 | Doc-Nr: PUB / 5283568 / 000 / 03...
  • Page 2 Printed: 14.12.2018 | Doc-Nr: PUB / 5283568 / 000 / 03...
  • Page 3 TE 50 TE 50-AVR Original operating instructions Printed: 14.12.2018 | Doc-Nr: PUB / 5283568 / 000 / 03...
  • Page 4 Printed: 14.12.2018 | Doc-Nr: PUB / 5283568 / 000 / 03...
  • Page 5: Information About The Documentation

    Information about the documentation 1.1 About this documentation • Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and use of the product. • Observe the safety instructions and warnings in this documentation and on the product.
  • Page 6 The type designation and serial number are printed on the rating plate. ▶ Write down the serial number in the table below. You will be required to state the product details when contacting Hilti Service or your local Hilti organization to inquire about the product.
  • Page 7 The technical documentation is filed here: Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916 Kaufering, Germany Safety 2.1 General power tool safety warnings WARNING Read all safety warnings and all instructions.
  • Page 8 ▶ If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. Personal safety ▶ Stay alert, watch what you are doing and use common sense when operating a power tool.
  • Page 9 ▶ Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
  • Page 10 ▶ Wear eye protection. Flying fragments present a risk of injury to the body and eyes. ▶ Before beginning the work, check the hazard classification of the dust that will be produced. Use an industrial vacuum cleaner with an officially approved protection classification in compliance with locally applicable dust protection regulations.
  • Page 11 English Printed: 14.12.2018 | Doc-Nr: PUB / 5283568 / 000 / 03...
  • Page 12 English Printed: 14.12.2018 | Doc-Nr: PUB / 5283568 / 000 / 03...
  • Page 13 Description 3.1 Overview of the product English Printed: 14.12.2018 | Doc-Nr: PUB / 5283568 / 000 / 03...
  • Page 14 Chuck Service indicator & Depth gauge Function selector switch Supply cord Control switch Side handle 3.2 Version with detachable supply cord Lockbutton Supply cord with keyed, re- leasable plug connector Connector on electric tool 3.3 Intended use The product described is an electrically-powered combihammer with pneu- matic hammering mechanism.
  • Page 15: Technical Data

    3.8 Items supplied Combihammer, side handle, operating instructions. Other system products approved for use with this product can be found at your local Hilti Store or online at: www.hilti.group. Technical data For rated voltage, rated current, frequency and/or input power, refer to the country-specific type identification plate.
  • Page 16: Operation

    TE 50­AVR Ambient temperature for operation 1 ℉ …140 ℉ (−17 ℃ …60 ℃) Ø hammer drill bits 1/2 in …1 1/4 in Ø hammer drill bits 12 mm …32 mm Ø drill bits for wood 1/4 in …1 3/8 in Ø...
  • Page 17 ➥ The product is ready for use. 3. Pull the chuck back as far as it will go and remove the accessory tool. Use only the recommended grease supplied by Hilti. Use of unsuit- able grease may cause damage to the product.
  • Page 18 5.2 Types of work ATTENTION Risk of damage by incorrect handling! ▶ Do not operate the switches for direction of rotation and/or function selection during operation. Observe the safety instructions and warnings in this documentation and on the product. 5.2.1 Drilling with hammering action (hammer drilling) 1.
  • Page 19 1. Set the function selector switch to the “Chisel positioning” position 2. Rotate the chisel to the desired position. 3. Turn the function selector switch until it engages in the “Chiseling” position. ➥ The product is ready for use. 5.3.1 Chiseling ▶...
  • Page 20: Care And Maintenance

    1. Push the lockbutton for continuous operation forward. 2. Press the on/off switch as far as it will go. ➥ The product then runs in sustained operating mode. 3. Push the lockbutton for continuous operation back. ➥ The product switches off. Detachable supply cord 6.1 Connecting the detachable supply cord CAUTION...
  • Page 21: Transport And Storage

    To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare parts, consumables and accessories approved by Hilti for use with the product can be found at your local Hilti Store or online at: www.hilti.group.
  • Page 22 Trouble or fault Possible cause Action to be taken The power tool The electronic restart ▶ Switch the power tool doesn’t start. interlock is activated off and then on again. after an interruption in the electric supply. No hammering ac- The power tool is too ▶...
  • Page 23: Manufacturer's Warranty

    The materials must be correctly separated before they can be recycled. In many countries, your old tools, machines or appli- ances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative for further information.
  • Page 24 English Printed: 14.12.2018 | Doc-Nr: PUB / 5283568 / 000 / 03...
  • Page 25 Printed: 14.12.2018 | Doc-Nr: PUB / 5283568 / 000 / 03...
  • Page 26 Hilti = registered trademark of Hilti Corp., Schaan 20181120 Printed: 14.12.2018 | Doc-Nr: PUB / 5283568 / 000 / 03...

This manual is also suitable for:

Te 50-avr

Table of Contents