WARNING • Always contact the Dacor Customer Service Team about problems and conditions that you don’t under- WARNING – NEVER use this appliance as a space stand. See Customer Service Information.
Do not touch the interior surfaces of the oven during how to turn off electric power to the oven. Dacor use. After use, make sure these surfaces have had is not responsible for service required to correct a sufficient time to cool before touching them.
Model Identification • If you have questions or problems with installation, con- tact your Dacor dealer or the Dacor Customer Service EORS227SCH Team. When you call, have the model and serial num- ber of the appliance ready. The model and serial num- ber are printed on the appliance data plate.
Product Specifications Power Supply Requirements • It is the owner’s responsibility to ensure that a licensed Model Dedicated Circuit total Connected electrician performs the installation of the electrical sup- Number Requirements* Load ply for this appliance. The electrical installation, includ- EORS127 ing minimum supply wire size, must comply with the MORS127...
Page 7
Design Specifications Product Dimensions All tolerances: +1/16 (1.6 mm). -0, unless otherwise stated. Light cover Conduit: 60” (152 cm) Long Control Panel Front Single Oven Side View Light cover Conduit: * Width at light 60” (152 cm) covers on sides Long Control Panel Front...
Installation Specifications Installation Planning • Dacor recommends installing the electrical junction box in the one of the locations shown. • Install the junction box in a location that allows the WARNING oven to be removed from the the cut out for service without being disconnected.
Page 9
Installation Specifications Cabinet Dimensions “M” “M” Recommended Recommended Electrical Electrical Location Location 1” (2.5 cm) min. to bottom of cabinet door 3/4” (1.9 cm) “P” “P” Support Platform “N” “N” 1” (2.5 cm) min. 1” (2.5 cm) min. to top of 3/4”...
Exhaust grill with 2 mounting screws (2, #8 X 3/8”, color should match exhaust grill: Silver Dacor PN • Mounting screws (Wood, #6 X ¾, Dacor PN 83331, 4 83571, Black Dacor PN 83263) for single ovens, 6 for double ovens) •...
Installation Instructions Electrical Connection Depending upon local codes, utilize one of three meth- WARNING ods to connect the appliance to the electrical power: • ◊ If the electrical service provided does not meet the Connect to a four wire electrical system Product Specifications (see page 4), do not proceed ◊...
Page 12
Installation Instructions Electrical Connection - (continued) Connecting to a Three Wire Electrical System with External Ground - Where Local Connecting to a Three Wire Electrical Codes Permit System - Where Local Codes Permit WARNING WARNING • Do not ground the appliance to a gas supply pipe or Do not connect the green appliance conduit wire to the hot water pipe.
Page 13
Installation Instructions Separate 10 AWG Wire Minimum Incoming Power Junction Box Wire Nut, 4 Places Clamp wire tightly to pipe Conduit to oven three Wire Connection with External Ground...
Installation Instructions Installing the Oven in the Cabinet Locate the mounting holes in the trim on both sides of the oven. There are four (4) holes, two (2) on each side, for single oven models and six (6) holes for dou- WARNING ble oven models.
Installation Instructions Installing the Exhaust Grill Reinstalling the Oven Doors With the oven secured to the cabinet, install the exhaust WARNING grill by mounting it to the oven with the two (2) provided screws. Failure to fully rotate the hinge catches will result in a safety hazard and may cause personal injury due to the door falling off its hinges.
Turn on power and repeat the above heating test. • If the appliance still does not work, contact an autho- rized Dacor service company. If you are unable to locate a service representative, please contact the Dacor Customer Service Team at (800) 793-0093, or visit us on the web at www.Dacor.com.
Need help?
Do you have a question about the EOR and is the answer not in the manual?
Questions and answers