Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Cisco Expressway CE1000 Appliance
Summary of Contents for Cisco Expressway CE1000 Appliance
- Page 1 Cisco Expressway CE1000 Appliance Installation Guide X8.2 or later December 2014...
-
Page 2: Table Of Contents
Changing the root account password Changing other system settings Checking for updates and upgrading Troubleshooting Locating LEDs and components Specific issues Document revision history Notices Technical support Accessibility notice Cisco Expressway CE1000 Appliance Installation Guide (8.5) Page 2 of 16... -
Page 3: Introduction
Introduction Introduction About this document This document describes how to install a Cisco Expressway CE1000 appliance into your video network. It contains information on: Preparing the installation Installing the hardware Performing initial configuration Troubleshooting the installation The Cisco Expressway appliance is based on the UCS C220 M3L. For more detailed information on installing... -
Page 4: Related Documents
To initiate a Return Material Authorization (RMA) go to http://www.cisco.com/web/ordering/cs_ info/or3/o32/Return_a_Product/WebReturns/product_Online_web_returns.html. Related documents Cisco Expressway Administrator Guide - describes how to maintain and operate the Cisco Expressway software. Cisco Expressway Cluster Creation and Maintenance Deployment Guide - describes how to create and maintain a cluster of Cisco Expressways. -
Page 5: Preparing To Install
Application/Software serial number: has the format 52XNNNNN, where X is a letter and N are numbers is displayed in the Cisco Expressway web interface, console and SSH session must be supplied to obtain release and option keys Cisco Expressway CE1000 Appliance Installation Guide (8.5) -
Page 6: Installing
Self Test and the unit will automatically restart. This is expected behavior. The system will be operational after it has booted up a second time. The first boot will take approximately 2 minutes. To verify the power status look at the Power Status LED (see Figure 3: Front view of the Cisco Expressway unit. [p.12]): Off—There is no AC power present in the server. -
Page 7: Configuring
Configuring Configuring Before you can use the Cisco Expressway, you must configure its IPv4 and/or IPv6 address, subnet mask and default gateway. Consult your network administrator for information on which addresses to use. Note that the Cisco Expressway must use a static IP address. -
Page 8: Connecting Via The Serial Port
KVM connector Connecting via the serial port To connect to the Cisco Expressway via the serial port: 1. Connect the Ethernet LAN cable from the LAN 1 port on the rear of the unit to your network. The LAN 1 port is the left-hand port of the dual port adapter on the rear panel of the unit (shown in Figure 1: Rear panel showing ports. -
Page 9: Connecting Via The Kvm Port
When you have connected to the Cisco Expressway and powered up the system, perform the following steps for the initial configuration: 1. If the system has just booted up, the terminal emulator program on the PC will display the Cisco Expressway’s startup information. After approximately four minutes you will get the login prompt. -
Page 10: Using The Web Interface
Restart Now? Type y and press Enter. 7. After it has rebooted, the Cisco Expressway is ready to use. You can access the Cisco Expressway's web interface via the IP address assigned to the LAN 1 Ethernet port. Note: for security reasons you are advised to change the password for the... -
Page 11: Changing The Root Account Password
Changing other system settings You are also required to configure the following: The system name of the Cisco Expressway. This is used by the Cisco TelePresence Management Suite (Cisco TMS) to identify the system. This can be set from the... -
Page 12: Troubleshooting
Locating LEDs and components Front view Below is an illustration of the unit's front view and a list of the LEDs and components available. Figure 3: Front view of the Cisco Expressway unit. Power button/power status LED Identification button/LED System status LED... -
Page 13: Specific Issues
Specific issues Active Options only indicates ‘150 traversal calls’ for Large deployments To utilize the Large scale capabilities (500 traversal calls) of the Cisco Expressway, the CE1000 unit must have an active 10Gb network connection. Cisco Expressway CE1000 Appliance Installation Guide (8.5) -
Page 14: Document Revision History
The following table summarizes the changes that have been applied to this document: Date Description December 2014 Updated for X8.5. June 2014 Updated for X8.2. April 2014 Initial release. Cisco Expressway CE1000 Appliance Installation Guide (8.5) Page 14 of 16... -
Page 15: Notices
Your contact email address or telephone number. A full description of the problem. To view a list of Cisco TelePresence products that are no longer being sold and might not be supported, visit: http://www.cisco.com/en/US/products/prod_end_of_life.html and scroll down to the TelePresence section. - Page 16 MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners.