Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Cisco VG400
Summary of Contents for Cisco VG400
- Page 1 Cisco VG400 Voice Gateway Software Configuration Guide First Published: 2018-11-30 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883...
- Page 2 © 2018 Cisco Systems, Inc. All rights reserved.
-
Page 3: Table Of Contents
Intended Audience Document Organization Obtain Documentation and Submit a Service Request C H A P T E R 1 Understanding Interface Numbering and Cisco IOS Software Basics Understanding Cisco IOS Software Basics Getting Help Command Modes Undoing a Command or Feature... - Page 4 Contents C H A P T E R 3 Configuring Voice Ports Prerequisite Configuring the Voice Port Cisco IOS Bulk Configuration Cisco VG400 Voice Gateway Software Configuration Guide...
-
Page 5: Preface
This preface presents the following major topics: Objectives After installing the Cisco VG400 Voice Gateway, use this guide to complete a basic router configuration using the setup command facility. This guide also contains information on using the Cisco IOS software to perform other configuration tasks, such as configuring voice ports and other features. -
Page 6: Obtain Documentation And Submit A Service Request
For information on obtaining documentation, using the Cisco Bug Search Tool (BST), submitting a service request, and gathering additional information, see What's New in Cisco Product Documentation To receive new and revised Cisco technical content directly to your desktop, you can subscribe to the What's New in Cisco Product Documentation: RSS Feed. -
Page 7: Understanding Interface Numbering And Cisco Ios Software Basics
CLI. Understanding these concepts will save time as you begin to use the commands. If you have never used Cisco IOS software or need a refresher, take a few minutes to read this chapter before you proceed to the next chapter. -
Page 8: Command Modes
Up Arrow key for more commands. Command Modes The Cisco IOS user interface is divided into different modes. Each command mode permits you to configure different components on your router. The commands available at any given time depend on which mode you are currently in. -
Page 9: Undoing A Command Or Feature
To install or upgrade to a new Cisco IOS release, see How to Update or Upgrade Cisco IOS Software Where to Go Next Now that you have learned some Cisco IOS software basics, you can begin to configure the router using the CLI. Remember that: •... - Page 10 Understanding Interface Numbering and Cisco IOS Software Basics Where to Go Next Cisco VG400 Voice Gateway Software Configuration Guide...
-
Page 11: Configuring With The Command-Line Interface
C H A P T E R Configuring with the Command-Line Interface This chapter describes how to use the Cisco IOS software CLI to configure the basic Cisco VG400 analog functionality. Follow the procedures described in this chapter to configure the Cisco VG400 Voice Gateway. Note that you can change the configuration after you have run the setup command facility. -
Page 12: Detailed Steps
CNTL/Z. Example: Router(config)# Step 3 Router(config)# hostname 450 Changes the name of Cisco VG400 to a meaningful name. Substitutes the host name to Router. Example: Step 4 Router(config)# enable secret guessme Enters an enable secret password. This password provides access to privileged EXEC mode. -
Page 13: Verifying The Host Name And Password
Exit global configuration mode and attempt to re-enter it using the new enable password: Example: Router# exit Router con0 is now available Press RETURN to get started. Router> enable Password: guessme Router# If you face any issues, check whether: • Caps Lock is off. Cisco VG400 Voice Gateway Software Configuration Guide... -
Page 14: Configuring A Gigabit Ethernet Interfaces
(manual configuration). Note Before you begin, disconnect all the WAN cables from Cisco VG400 to prevent it from running the AutoInstall process. Cisco VG400 attempts to run AutoInstall whenever you power the Voice Gateway on and there is a WAN connection on both ends. -
Page 15: Saving Configuration Changes
Returns to enable mode when you finish configuring interfaces. Example: Router# Saving Configuration Changes To prevent the loss of the Cisco VG400 configuration, save the configuration changes to NVRAM. SUMMARY STEPS 1. Router> enable 2. Router# copy running-config startup-config 3. Router(config-if)# Ctrl-z... -
Page 16: Enabling Uc License
Example: Router# Example: %SYS-5-CONFIG_I: Configured from console by console Enabling UC License To enable the UC license in the Cisco VG400 Voice Gateway, perform the following steps: Summary Steps 1. enable 2. configure terminal 3. license accept end user agreement 4. -
Page 17: Configuring The Voice Port
Returns to privileged EXEC mode. Example: Router(config)# exit Step 6 write Saves the configuration. Example: Router# write Step 7 reload Reloads the router. Example: Router# reload Configuring the Voice Port SUMMARY STEPS 1. enable 2. configure terminal Cisco VG400 Voice Gateway Software Configuration Guide... - Page 18 (describing the voice port) attached to the configuration. Step 5 no shutdown Activates the voice port. If a voice port is not being used, shut down the voice port by using the shutdown command. Example: Router(config-voiceport)# no shutdown Cisco VG400 Voice Gateway Software Configuration Guide...
- Page 19 [no] loop-length [long | short] The loop-length CLI has the following characteristics: • For the Cisco VG400 platform, the default is short loop-length. This command is not applicable to analog FXS on motherboard slot. • This command is applicable to all 48 FXS voice ports on SM-D-48FXS-E and the first 4 (0-3) FXS voice ports on SM-D-72FX like the Cisco VG400 platform.
- Page 20 FXS voice ports. vmwi [fsk | dc-voltage] For configuration examples, see Cisco VG400 Configuration Examples. Cisco IOS Bulk Configuration An optional bulk-configuration mechanism for voice-port and voice dial peer is available to save on time.
- Page 21 • Multiple port commands are allowed and can be removed one by one with exact port specification or all at once using no port all • No overlay port commands are allowed. As a result, no other port commands are allowed if port all is configured. Cisco VG400 Voice Gateway Software Configuration Guide...
- Page 22 Configuring Voice Ports Cisco IOS Bulk Configuration Cisco VG400 Voice Gateway Software Configuration Guide...