Table of Contents
Advertisement
Quick Links
Q
S
G
UICK
TART
Cisco Physical Access Gateway Quick Start Guide
1
Summary Steps
2
Cisco Physical Access Gateway
3
Wall Mounting a Gateway or Optional Module
4
Cisco Physical Access Reader Module
5
Cisco Physical Access Output Module
6
Cisco Physical Access Input Module
7
Obtaining Documentation and Submitting a Service Request
UIDE
Advertisement
Table of Contents
Related Manuals for Cisco Physical Access Gateway
Summary of Contents for Cisco Physical Access Gateway
- Page 1 UICK TART UIDE Cisco Physical Access Gateway Quick Start Guide Summary Steps Cisco Physical Access Gateway Wall Mounting a Gateway or Optional Module Cisco Physical Access Reader Module Cisco Physical Access Output Module Cisco Physical Access Input Module Obtaining Documentation and Submitting a Service Request...
-
Page 2: Summary Steps
Summary Steps The following steps are an example of the main installation and configuration tasks for a Cisco Physical Access Control system. The exact procedures and order of installation for your system may vary. To ensure proper operation, perform a test installation of all equipment on a lab bench before actual installation: use Cisco PAM to configure the Gateways and all peripheral devices including locks, readers, and sensors. - Page 3 Enter the Cisco PAM IP address (IP address or name) to enable Gateway communication with the appliance. b. Enter the port number for the Cisco PAM appliance. The port number must be greater than 1024 and less 65535. The default is 8020.
-
Page 4: Package Contents
3 Pin 2 Pin Gateway Module Overview and Port Descriptions The Cisco Physical Access Gateway includes connections for power, Ethernet, door readers and other input and output devices, as shown in Figure 2. Figure 2 Cisco Physical Access Gateway Ports and Connectors: Side View... - Page 5 Two-pin connector for Voltage In (VIN) and Ground (GND) to connect a 12 to 24 VDC external power source. A three-wire CAN bus is used to connect additional modules, including the Cisco Reader Module, Cisco Input Module, and Cisco Output Module.
- Page 6 • C & NC connection: The relay is normally closed. The circuit is opened when triggered. Notes: • Install surge protection between the output device and the Cisco PAM module. See the Cisco Physical Access Gateway User Guide for instructions.
-
Page 7: Wall Mount Installation Kit Contents
Wall Mounting a Gateway or Optional Module Each Cisco Physical Access Gateway and optional module includes two mounting brackets and four screws to mount the gateway to the wall. Figure 3 shows the three options for attaching the included wall-mount brackets to a module. -
Page 8: What's In The Box
See Wall Mounting a Gateway or Optional Module, page 7. Reader Module Overview and Port Descriptions The Cisco Reader Module includes ports for connecting up to two doors and associated input and output devices, as shown in Figure 4. Figure 4... - Page 9 • A supervised input senses four contact states, including Normal, Alarm, Open and Short. These inputs require 1K End-Of-Line (EOL) termination resistors installed at the contacts (two resistors are included in the accessory kits for each Input port). Refer to Cisco Physical Access Gateway User Guide for instructions to install the termination resistors.
- Page 10 • C & NC connection: The relay is normally closed. The circuit is opened when triggered. Notes: • Install surge protection between the output device and the Cisco PAM module. See the Cisco Physical Access Gateway User Guide for instructions.
-
Page 11: Output Module Overview And Port Descriptions
3 Pin 2 Pin Output Module Overview and Port Descriptions The Cisco Output Module includes 10 ports for connecting additional output devices, as shown in Figure 5. Figure 5 Cisco Output Module Ports and Connectors The following items are shown in Figure 5:... - Page 12 • C & NC connection: The relay is normally closed. The circuit is opened when triggered. Notes: • Install surge protection between the output device and the Cisco PAM module. See the Cisco Physical Access Gateway User Guide for instructions.
-
Page 13: Cisco Physical Access Input Module
3 Pin 2 Pin Input Module and Port Descriptions The Cisco Input Module includes 10 ports for connecting additional input devices, as shown in Figure 6. Figure 6 Cisco Input Module Ports and Connectors The following items are shown in Figure 6:... -
Page 14: Obtaining Documentation And Submitting A Service Request
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0. - Page 16 Cisco Website at www.cisco.com/go/offices. Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company.