Hilti ST 2500 Operating Instructions Manual
Hide thumbs
Also See for ST 2500:
- Operating instructions manual (149 pages) ,
- Original operating instructions (133 pages) ,
- Manual (132 pages)
Table of Contents
Advertisement
Quick Links
Printed: 07.07.2013 | Doc-Nr: PUB / 5139759 / 000 / 00
ST 2500
SD 2500
Bedienungsanleitung
Operating instructions
Mode d'emploi
Istruzioni d'uso
Gebruiksaanwijzing
Manual de instruções
Manual de instrucciones
Brugsanvisning
Käyttöohje
Bruksanvisning
Bruksanvisning
Οδηγιες χρησεως
Kasutusjuhend
Lietošanas pamācība
Instrukcija
de
en
fr
it
nl
pt
es
da
fi
no
sv
el
et
lv
lt
ar
Advertisement
Table of Contents
Related Manuals for Hilti ST 2500
Summary of Contents for Hilti ST 2500
- Page 1 ST 2500 SD 2500 Bedienungsanleitung Operating instructions Mode d’emploi Istruzioni d’uso Gebruiksaanwijzing Manual de instruções Manual de instrucciones Brugsanvisning Käyttöohje Bruksanvisning Bruksanvisning Οδηγιες χρησεως Kasutusjuhend Lietošanas pamācība Instrukcija Printed: 07.07.2013 | Doc-Nr: PUB / 5139759 / 000 / 00...
- Page 2 ST 2500 SD 2500 Printed: 07.07.2013 | Doc-Nr: PUB / 5139759 / 000 / 00...
- Page 3 III. Click Printed: 07.07.2013 | Doc-Nr: PUB / 5139759 / 000 / 00...
-
Page 4: Table Of Contents
The illustrations can be found on the fold-out cover pages. Keep these pages open while studying the operating instructions. In these operating instructions, the ST 2500 or SD 2500 electric screwdriver is referred to as "the tool". Contents Page... -
Page 5: Description
2.1 Use of the tool as directed or drywall installation work is taking place. The ST 2500 is a hand-held, electric mains-powered tool Only the specified screwdriving bits, magazine and acces- for driving screws used to fasten sheet metal in metal sories may be used with the tool. -
Page 6: Tools And Accessories
Weight as per EPTA-Procedure 01/2003 1.5 kg (ST 2500) 1.6 kg (SD 2500) Dimensions (L×W×H) (ST 2500) 242× 72×194 mm/(SD 2500) 272× 72×194 mm ″ hex. socket (keyed hold) with ST 2500 Chuck ″ hex. socket (friction hold) with SD 2500 Speed under no load 0–2200 r.p.m. -
Page 7: Safety Rules
Noise and vibration information (measured in accordance with EN 60745): Typical A-weighted sound power level (L 95 dB (A) Typical A-weighted sound pressure level (L 84 dB (A) For the given sound power level as per EN 60745, the tolerance is 3 dB. It is recommended that ear protection is worn. - Page 8 Store idle power tools out of the reach of children um cleaner of the type recommended by Hilti for and do not allow persons unfamiliar with the pow- wood dust and/or mineral dust together with this er tool or these instructions to operate the power tool.
-
Page 9: Before Use
5.2.4 Work area 5.2.5 Personal protective equipment The operator and other persons in the immediate vicinity a) Ensure that the workplace is well lit. must always wear eye protection and ear protection b) Ensure that the workplace is well ventilated. Poor- while the tool is in use. -
Page 10: Care And Maintenance
If necessary, your Keep the power tool, especially its grip surfaces, clean electric tool should be repaired at a Hilti repair center. and free from oil and grease. Do not use cleaning agents Repairs to the electrical section of the tool may be car- which contain silicone. -
Page 11: Disposal
9. Disposal Most of the materials from which Hilti electric tools are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old electric tools for recycling. Please ask your Hilti customer service department or Hilti representative for further information. - Page 12 Tel.: +423 / 234 21 11 Fax:+423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 2823 | 0113 | 10-Pos. 1 | 1 Printed in Liechtenstein © 2013 Right of technical and programme changes reserved S. E. & O 378505 / A3 Printed: 07.07.2013 | Doc-Nr: PUB / 5139759 / 000 / 00...