Page 1 GS1900 Series GbE Smart Managed Switch Version 1.0 Edition 2, 08/2013 Quick Start Guide User’s Guide Default Login Details IP Address http://192.168.1.1 (In-band ports) User Name admin www.zyxel.com Password 1234 Copyright © 2013 ZyXEL Communications Corporation...
Page 2 Note: It is recommended you use the Web Configurator to configure the Switch. • Web Configurator Online Help Click the help icon in any screen for help in configuring that screen and supplementary information. GS1900 Series User’s Guide...
Page 3: Table Of Contents
Configuration: Link Aggregation ......................126 Configuration: Loop Guard ........................133 Configuration: Mirror ..........................136 Configuration: Multicast .........................138 Configuration: Spanning Tree .......................146 Configuration: LLDP ..........................156 Configuration: QoS ..........................169 Configuration: Security ..........................178 Configuration: AAA ..........................187 Configuration: Management ........................193 Maintenance ............................211 Troubleshooting ............................222 GS1900 Series User’s Guide...
Page 4: Table Of Contents
3.1.2 SFP Slots ..........................26 3.2 Rear Panel ............................28 3.2.1 Power Connection ........................29 3.3 LEDs .............................30 Chapter 4 The Web Configurator ........................31 4.1 Overview ............................31 4.2 Access ...............................31 4.3 Navigating the Web Configurator ......................32 4.3.1 Title Bar ...........................32 GS1900 Series User’s Guide...
Page 5 7.4.1 Bandwidth Control ........................59 7.5 Storm Control ............................60 Chapter 8 Monitor: VLAN.............................61 8.1 Overview ............................61 8.1.1 What You Can Do in this Chapter ....................61 8.2 VLAN ..............................61 8.2.1 VLAN ............................61 8.2.2 Port ............................62 8.2.3 VLAN Port ..........................63 GS1900 Series User’s Guide...
Page 6 13.1.1 What You Can Do in this Chapter ..................78 13.2 Spanning Tree ..........................78 13.2.1 CIST ............................78 13.2.2 CIST Port ..........................79 13.2.3 MST ............................80 13.2.4 MST Port ..........................81 13.2.5 STP Statistics ........................82 Chapter 14 Monitor: LLDP .............................84 GS1900 Series User’s Guide...
Page 7 17.4 Information ............................96 17.4.1 The System Information Screen ...................97 Chapter 18 Configuration: Port..........................98 18.1 Overview ............................98 18.1.1 What You Can Do in this Chapter ..................98 18.2 Port ..............................98 18.2.1 The Port Edit Screen ......................99 18.3 EEE ...............................100 GS1900 Series User’s Guide...
Page 8 20.2.1 The Static MAC Screen .......................122 20.2.2 The Static MAC Add Screen ....................123 20.2.3 The Filtering MAC Screen ....................123 20.2.4 The Filtering MAC Add Screen ...................124 20.2.5 The Dynamic Age Screen ....................124 Chapter 21 Configuration: Link Aggregation ....................126 GS1900 Series User’s Guide...
Page 9 24.2.5 The Add/Edit Router Port Screen ..................141 24.2.6 The Profile Screen .......................142 24.2.7 The Add/Edit Profile Screen ....................143 24.2.8 The Throttling Screen ......................144 24.2.9 The Add/Edit Throttling Screen ...................144 Chapter 25 Configuration: Spanning Tree ......................146 25.1 Overview ............................146 25.2 Spanning Tree ..........................146 GS1900 Series User’s Guide...
Page 10 27.2.5 The DSCP Mapping Screen ....................173 27.2.6 The IP Precedence Mapping Screen ...................174 27.3 Trust Mode ............................175 27.3.1 The Global Screen .......................175 27.3.2 The Port Screen ........................175 27.3.3 The Trust Mode Edit Screen ....................176 Chapter 28 Configuration: Security........................178 28.1 Overview ............................178 GS1900 Series User’s Guide...
Page 11 30.2.3 The Local Add/Modify Screen ....................194 30.2.4 The Remote Screen ......................195 30.2.5 The Remote Add/Modify Screen ..................195 30.3 SNMP ............................196 30.3.1 The Global Screen .......................196 30.3.2 The Community Screen .......................197 30.3.3 The Community Add/Modify Screen ...................198 30.3.4 The Group Screen .......................198 GS1900 Series User’s Guide...
Page 12 31.5.1 Overview ..........................216 31.6 Reset to Factory Defaults ......................217 31.6.1 Overview ..........................217 31.6.2 Reset the Switch to Factory Defaults ...................217 31.7 Network Diagnostics ........................217 31.7.1 Port Test ..........................217 31.7.2 IPv4 Ping Test ........................218 31.7.3 IPv6 Ping Test ........................219 GS1900 Series User’s Guide...
Page 13 31.8 Reboot ............................221 31.8.1 Overview ..........................221 31.8.2 Reboot the Switch .......................221 Chapter 32 Troubleshooting..........................222 32.1 Power, Hardware Connections, and LEDs ..................222 32.2 Switch Access and Login ......................223 32.3 Switch Configuration ........................225 Appendix A Legal Information......................226 Index ..............................228 GS1900 Series User’s Guide...
Page 14: User's Guide
User’s Guide...
Page 16: Getting To Know Your Switch
Getting to Know Your Switch This chapter introduces the main features and applications of the Switch. 1.1 Introduction The GS1900 series is a new generation Gigabit Ethernet (GbE) Web-Managed Switch. This User’s Guide covers the following models: Table 1 GS1900 Series Comparison Table...
Page 17: Gigabit Ethernet To The Desktop
1.1.3 IEEE 802.1Q VLAN Application Example A VLAN (Virtual Local Area Network) allows a physical network to be partitioned into multiple logical networks. Stations on a logical network belong to one or more groups. With VLAN, a station cannot GS1900 Series User’s Guide...
Page 18: Ipv6 Support
• ICMPv6 to report errors encountered in packet processing and perform diagnostic functions, such as "PING” • IPv4/IPv6 dual stack; the Switch can run IPv4 and IPv6 at the same time • DHCPv6 client • Multicast Listener Discovery (MLD) snooping GS1900 Series User’s Guide...
Page 19: Ways To Manage The Switch
Switch to its factory default settings. If you backed up an earlier configuration file, you would not have to totally re-configure the Switch. You could simply restore your last configuration. GS1900 Series User’s Guide...
Page 20: Hardware Installation And Connection
Note: Do NOT block the ventilation holes. Leave space between devices when stacking. Note: For proper ventilation, allow at least 4 inches (10 cm) of clearance at the front and 3.4 inches (8 cm) at the back of the Switch. This is especially important for enclosed rack installations. GS1900 Series User’s Guide...
Page 21: Hardware Installation
Note: Make sure the screws are securely fixed to the wall and strong enough to hold the weight of the Switch with the connection cables. Align the holes on the back of the Switch with the screws on the wall. Hang the Switch on the screws. GS1900 Series User’s Guide...
Page 22: Rack Mounting
Attaching the Mounting Brackets to the Switch Position a mounting bracket on one side of the Switch, lining up the four screw holes on the bracket with the screw holes on the side of the Switch. GS1900 Series User’s Guide...
Page 23 Position a mounting bracket (that is already attached to the Switch) on one side of the rack, lining up the two screw holes on the bracket with the screw holes on the side of the rack. GS1900 Series User’s Guide...
Page 24 Figure 8 Mounting the Switch on a Rack (GS1900-24, GS1900-24HP, GS1900-48, GS1900-48HP) Using a #2 Philips screwdriver, install the M5 flat head screws through the mounting bracket holes into the rack. Repeat steps to attach the second mounting bracket on the other side of the rack. GS1900 Series User’s Guide...
Page 25: Hardware Overview
3.1 Front Panel Connections The following figures show the front panels of the Switch. Figure 9 Front Panel: GS1900-8 Figure 10 Front Panel: GS1900-8HP Figure 11 Front Panel: GS1900-16 Figure 12 Front Panel: GS1900-24E Figure 13 Front Panel: GS1900-24 GS1900 Series User’s Guide...
Page 26: Ethernet Ports
Use a transceiver to connect a fiber-optic cable to the Switch. The Switch does not come with transceivers. You must use transceivers that comply with the Small Form-Factor Pluggable (SFP) Transceiver MultiSource Agreement (MSA). See the SFF committee’s INF-8074i specification Rev 1.0 for details. GS1900 Series User’s Guide...
Page 27 The Switch automatically detects the installed transceiver. Check the LEDs to verify that it is functioning properly. Figure 18 Installed Transceiver 3.1.2.2 Transceiver Removal Use the following steps to remove a transceiver. Open the transceiver’s latch (latch styles vary). Figure 19 Opening the Transceiver’s Latch Example GS1900 Series User’s Guide...
Page 28: Rear Panel
Figure 20 Transceiver Removal Example 3.2 Rear Panel The following figures show the rear panels of the Switch. Figure 21 Rear Panel: GS1900-8 Figure 22 Rear Panel: GS1900-8HP Figure 23 Rear Panel: GS1900-16 Figure 24 Rear Panel: GS1900-24E GS1900 Series User’s Guide...
Page 29: Power Connection
Switch power on or off. Connecting the Power Use the following procedures to connect the Switch to a power source after you have installed it in a rack. Note: Use the included power cord for the AC power connection. GS1900 Series User’s Guide...
Page 30: Leds
1G SFP Slots (Fiber Ports - see Section 1.1 on page LNK/ACT Green Blinking The system is transmitting/receiving to/from a 100/1000 Mbps Fiber network. The link to a 100/1000 Mbps Fiber network is up. The link to a Fiber network is down. GS1900 Series User’s Guide...
Page 31: The Web Configurator
4.2 Access Make sure your Switch hardware is properly connected. See the Quick Start Guide. Browse to https://192.168.1.1. The Login screen appears. Figure 29 The Login Screen Enter the user name (default: “admin”) and password (default: “1234”). GS1900 Series User’s Guide...
Page 32: Navigating The Web Configurator
Click this to apply your changes to the Switch’s run-time memory. The Switch loses these changes if it is turned off or loses power, so use the Save link on the top navigation panel to save your changes to the non-volatile memory when you are done configuring. GS1900 Series User’s Guide...
Page 33: Navigation Panel
Figure 17 Web Configurator: Logout Screen 4.3.2 Navigation Panel Use the menu items on the navigation panel to open screens to configure Switch features. The following sections introduce the Switch’s navigation panel menus and their screens. Figure 32 Navigation Panel GS1900 Series User’s Guide...
Page 34 This link takes you to a screen where you can view protection against network loops that occur on the edge of your network. Multicast This link takes you to screen where you can view various multicast features, IGMP snooping and create multicast VLANs. GS1900 Series User’s Guide...
Page 35: Configuration Menu
Port This link takes you to screens where you can configure speed, flow control and priority settings for individual Switch ports. Port Configure port settings for individual Switch ports. Configure EEE settings for individual Switch ports. GS1900 Series User’s Guide...
Page 36 Router Port Configure router port settings. Profile Configure profile settings. Throttling Configure throttling settings. Spanning Tree This link takes you to screens where you can configure the RSTP/ MRSTP/MSTP to prevent network loops. Global Configure global settings. GS1900 Series User’s Guide...
Page 37 Access-Control System Plus). Auth Method Configure auth method settings. RADIUS Configure RADIUS settings. TACACS+ Configure TACACS+ settings. Management Configure syslog, SNMP, error disable, HTTP/HTTPS, users and remote access control. Syslog Global Configure global settings. Local Configure local settings. GS1900 Series User’s Guide...
Page 38 This link takes you to screens where you can view system logs and can test port(s). Port Test Cable Diag Manage cable diag and test results. PING IPv4 Manage ping test settings. IPv6 Manage IPv6 ping test settings. Trace Manage trace route settings. Reboot Reset the system. GS1900 Series User’s Guide...
Page 39: Getting Start
Virtual Device Displays an image of the Switch. Wizard Displays the following links: Start up, VLAN, QoS, and link aggregation. Device Information System Name This field displays the name used to identify the Switch on any network. GS1900 Series User’s Guide...
Page 40: Wizard
In order to set up your IP/DNS, please do the following. Click Getting Start > Start up > 1 Step 1 Set up IP/DNS to access this screen. Figure 34 Getting Start > Start up > 1 Step 1 Set up IP/DNS GS1900 Series User’s Guide...
Page 41 The default username is admin and associated default password is 1234. Password The default username is admin and associated default password is 1234. Previous Click Previous to show the previous screen. Next Click Next to show the next screen. After clicking Next, the finish screen appears. GS1900 Series User’s Guide...
Page 42 In VLAN, you can create VLAN, tag VLAN setting, and view finished results. In order to create VLAN, please do the following. Click Getting Start > VLAN > 1 Step 1 Create VLAN to access this screen. GS1900 Series User’s Guide...
Page 43 Select from the drop-box a VLAN ID. Next Click Next to show the next screen. After clicking Next, the tag VLAN setting screen appears. Figure 38 Getting Start > VLAN > 2 Step 2 Tag VLAN Setting GS1900 Series User’s Guide...
Page 44 Ports belonging to the specified VLAN don't tag all outgoing frames transmitted. Previous Click Previous to show the previous screen. Finish Review the information and click Finish to create the task. In QoS, you can create QoS settings, and view finished results. GS1900 Series User’s Guide...
Page 45 Click and drag icons located on the left to desired preference. Click and drag icons located on the left to desired preference. Next Click Next to show the next screen. After clicking Next, the finish screen appears. GS1900 Series User’s Guide...
Page 46 In link aggregation, you can link aggregation and view finished results. In order to create link aggregation settings, please do the following. Click Getting Start > Link aggregation > 1 Step 1 Link aggregation to access this screen. GS1900 Series User’s Guide...
Page 47 Click and drag icons located on the left to desired preference. Group 8 Click and drag icons located on the left to desired preference. Next Click Next to show the next screen. After clicking Next, the finish screen appears. GS1900 Series User’s Guide...
Page 48 Displays summary results. Group 6 Displays summary results. Group 7 Displays summary results. Group 8 Displays summary results. Previous Click Previous to show the previous screen. Finish Review the information and click Finish to create the task. GS1900 Series User’s Guide...
Page 49: Technical Reference
Technical Reference The appendices provide general information. Some details may not apply to your Switch.
Page 51: Monitor: System
The factory default subnet mask is 255.255.255.0. 6.2.1 IPv4 Use this screen to view the Switch’s IPv4 information. Click Monitor > System > IP > IPv4 to open this screen. Figure 44 Monitor > System > IP > IPv4 GS1900 Series User’s Guide...
Page 52: Ipv6
This field displays IP address of the Switch in the IP domain. IPv6 Gateway This field displays the IP address of the default outgoing gateway. DHCPv6 Client This field displays the Switch’s DHCP settings when it is acting as a DHCPv6 client. GS1900 Series User’s Guide...
Page 53: Information
This field displays the descriptive name of the Switch for identification purposes. System Location This field displays the geographic location of the Switch for identification purposes. System Contact This field displays the person in charge of the Switch for identification purposes. GS1900 Series User’s Guide...
Page 54: Monitor: Port
Figure 47 Monitor > Port > Port > Status Each field is described in the following table. Table 22 Monitor > Port > Port > Status LABEL DESCRIPTION Port This is the port index number. Port Name A descriptive name that identifies this port. GS1900 Series User’s Guide...
Page 55: Port Counters
Figure 48 Monitor > Port > Port > Port Counters Each field is described in the following table. Table 23 Monitor > Port > Port > Port Counters LABEL DESCRIPTION Interface Port This field displays the port. GS1900 Series User’s Guide...
Page 56 This field displays the etherStatsFragments. etherStatsJabbers This field displays the etherStatsJabbers. etherStatsCollisions This field displays the etherStatsCollisions. etherStatsPkts64Octets This field displays the etherStatsPkts64Octets. etherStatsPkts65to127Octets This field displays the etherStatsPkts65to127Octets. etherStatsPkts128to255Octets This field displays the etherStatsPkts128to255Octets. GS1900 Series User’s Guide...
Page 57: Bandwidth Utilization
This field displays the link down. Refresh period This field displays the refresh period. This field displays the IFG. Transmitted (Tx) traffic during the last time interval in seconds. Received (Rx) traffic during thetime interval in seconds. GS1900 Series User’s Guide...
Page 58: Poe
This field displays the total power the Switch can provide to the connected PoE-enabled devices on the PoE ports. Consuming This field displays the total amount of power the Switch is currently supplying to the Power(W) connected PoE-enabled devices. GS1900 Series User’s Guide...
Page 59: Bandwidth Management
This field specifies the current egress burst size in bytes all ports. Burst Port Rate View the maximum bandwidth allowed in kilobits per second (Kbps) for the traffic flow on a port. Port This field displays the port number. GS1900 Series User’s Guide...
Page 60: Storm Control
Displays how many unknown unicast packets the port receives (in pps). Unicast (pps) Action Displays the action the device takes when a limit is reached. The following options are available: • Drop - drop the packet. • Shutdown - shutdown the connection. GS1900 Series User’s Guide...
Page 61: Monitor: Vlan
65) displays the global and port settings of the Switch. 8.2 VLAN Use this screen to view Switch VLAN settings. 8.2.1 VLAN Use this screen to view the Switch’s VLAN settings. Click Monitor > VLAN > VLAN > VLAN to access this screen. GS1900 Series User’s Guide...
Page 62: Port
This is the port VLAN identification number. A PVID (Port VLAN ID) is a tag that adds to incoming untagged frames received on a port so that the frames are forwarded to the VLAN group that the tag defines. GS1900 Series User’s Guide...
Page 63: Vlan Port
Figure 56 Monitor > VLAN > VLAN > VLAN Port Each field is described in the following table. Table 30 Monitor > VLAN > VLAN > VLAN Port LABEL DESCRIPTION VLAN Port VLAN ID This is the VLAN identification number. GS1900 Series User’s Guide...
Page 64: Guest Vlan
Figure 57 Guest VLAN Example VLAN 100 VLAN 102 Internet Use this screen to view the Switch’s guest VLAN. Click Monitor > VLAN > Guest VLAN to access this screen. Figure 58 Monitor > VLAN > Guest VLAN GS1900 Series User’s Guide...
Page 65: Voice Vlan
This is the voice VLAN identification number. Cos/802.1p This displays the packet’s 802.1p priority field. Remark Cos/802.1p This field displays the state of the cos/802.1p. Aging Time (30-65536 min) Displays the time interval (from 30 to 65536) in minutes. Port GS1900 Series User’s Guide...
Page 66 Chapter 8 Monitor: VLAN Table 32 Monitor > VLAN > Voice VLAN (continued) LABEL DESCRIPTION Port This field displays a port number. State This field displays the state of a port. GS1900 Series User’s Guide...
Page 67: Monitor: Mac Table
Figure 60 MAC Table Flowchart This link takes you to a screen where you can view the MAC address and VLAN ID of a device attach to a port. You can also view what kind of MAC address it is. GS1900 Series User’s Guide...
Page 68: What You Can Do In This Chapter
This shows whether the MAC address is dynamic (learned by the Switch) or static (manually entered in the Static MAC Forwarding screen). Port This is the port from which the above MAC address was learned. Total Entries Displays the number of total entries. GS1900 Series User’s Guide...
Page 69: Monitor: Link Aggregation
69) displays link aggregation status. 10.2 Link Aggregation Use the Link Aggregation screens to view Switch link aggregation status. Click Monitor > Link Aggregation > LAG to access this screen. Figure 62 Monitor > Link Aggregation > LAG GS1900 Series User’s Guide...
Page 70 Link Status This field displays the status of the link. Active Member Displays if this member is an active member of a trunk. Standby Member Displays if this member is an standby member of a trunk. GS1900 Series User’s Guide...
Page 71: Monitor: Loop Guard
B. Since switch B is in loop state, the probe packet P returns to port N on A. The Switch then shuts down port N to ensure that the rest of the network is not affected by the switch in loop state. GS1900 Series User’s Guide...
Page 72: What You Can Do In This Chapter
• The Loop Guard screen (Section 11.2 on page 72) displays loop guard status. 11.2 Loop Guard Use the Loop Guard screen to view Switch loop guard status. Click Monitor > Loop Guard to access this screen. GS1900 Series User’s Guide...
Page 73 DESCRIPTION Loop Guard Status Port This field displays a port number. Status This field displays the status. Time Left (sec) This field displays the amount of time left in seconds. Action This field displays the action. GS1900 Series User’s Guide...
Page 74: Monitor: Multicast
Use this screen to view Switch various multicast features. 12.2.1 Vlan Use this screen to view the Switch’s IGMP vlan. Click Monitor > Multicast > IGMP > Vlan to access this screen. Figure 67 Monitor > Multicast > IGMP > Vlan GS1900 Series User’s Guide...
Page 75: Statistics
This field displays the number of total entries. 12.2.2 Statistics Use this screen to view the Switch’s IGMP statistics. Click Monitor > Multicast > IGMP > Statistics to access this screen. Figure 68 Monitor > Multicast > IGMP > Statistics GS1900 Series User’s Guide...
Page 76: Group
Figure 69 Monitor > Multicast > IGMP > Statistics > Reset 12.2.3 Group Use this screen to view the Switch’s IGMP group. Click Monitor > Multicast > IGMP > Group to access this screen. GS1900 Series User’s Guide...
Page 77: Router
This field displays the dynamic router ports. Static Router Ports This field displays the static router ports. Forbidden Router Ports This field displays the forbidden router ports. Total Entries This field displays the number of total entries. GS1900 Series User’s Guide...
Page 78: Monitor: Spanning Tree
Use this screen to view Switch spanning tree settings. 13.2.1 CIST Use this screen to view the Switch’s spanning tree CIST instance. Click Monitor > Spanning Tree > CIST to access this screen. Figure 72 Monitor > Spanning Tree > CIST GS1900 Series User’s Guide...
Page 79: Cist Port
13.2.2 CIST Port Use this screen to view the Switch’s spanning tree CIST port status. Click Monitor > Spanning Tree > CIST Port to access this screen. Figure 73 Monitor > Spanning Tree > CIST Port GS1900 Series User’s Guide...
Page 80: Mst
This field displays the state of the port. 13.2.3 MST Use this screen to view the Switch’s spanning tree MST instance. Click Monitor > Spanning Tree > MST to access this screen. Figure 74 Monitor > Spanning Tree > MST GS1900 Series User’s Guide...
Page 81: Mst Port
Select a number from the drop-down menu to display results. Port This field displays the port number. MSTI ID A VLAN can be mapped to a specific Multiple Spanning Tree Instance (MSTI). MSTI allows multiple VLANs to use the same spanning tree. GS1900 Series User’s Guide...
Page 82: Stp Statistics
Note: In this user’s guide, “STP” refers to both STP and RSTP. Use this screen to view the Switch’s spanning tree STP statistics. Click Monitor > Spanning Tree > STP Statistics to access this screen. Figure 76 Monitor > Spanning Tree > STP Statistics GS1900 Series User’s Guide...
Page 83 This field displays the Multiple Spanning Tree Protocol (MSTP) BDPUs received. Received Configuration This field displays the configuration BDPUs transmitted. BDPUs Transmitted TCN BDPUs This field displays the TCN BDPUs transmitted. Transmitted MSTP BDPUs This field displays the Multiple Spanning Tree Protocol (MSTP) BDPUs transmitted. Transmitted GS1900 Series User’s Guide...
Page 84: Monitor: Lldp
14.2.1 Statistics Use this screen to view the Switch’s LLDP global and port statistics. Click Monitor > LLDP > Statistics to access this screen. Figure 77 Monitor > LLDP > Statistics GS1900 Series User’s Guide...
Page 85: Remote Information
This field displays the port ID subtype. Port ID This field displays the port ID. System Name This field displays the descriptive name of the Switch for identification purposes. Time to Live This field displays the live time of this entry. GS1900 Series User’s Guide...
Page 86: Overloading
Optional TLVs This field displays how many bytes used by optional TLVs. MED Inventory This field displays how many bytes used by MED inventory. 802.1 TLVs This field displays how many bytes used by 802.1 TLVs. GS1900 Series User’s Guide...
Page 87: Monitor: Security
When total MAC address entry is 8k, static MAC can't be configured. Use this screen to view Switch port security settings. Click Monitor > Security > Port Security to access this screen. Figure 80 Monitor > Security > Port Security GS1900 Series User’s Guide...
Page 88: Port
Each field is described in the following table. Table 49 Monitor > Security > 802.1x > Port LABEL DESCRIPTION Port This label shows the port you are viewing. Status This field displays status of the port. GS1900 Series User’s Guide...
Page 89: Authenticated Hosts
This label shows the port you are viewing. Session Time This label shows the session time. Authentication This label shows the authentication method. Method MAC Address This field displays the source MAC address in the binding. GS1900 Series User’s Guide...
Page 90: Monitor: Management
(Section 16.3 on page 91) displays global and port. 16.2 Syslog Use this screen to view Switch syslog management. Click Monitor > Management > Syslog to access this screen. Figure 83 Monitor > Management > Syslog GS1900 Series User’s Guide...
Page 91: Error Disable
This link takes you to a screen where you can view CPU protection and error disable recovery. Use this screen to view Switch global and port error disable management. Click Monitor > Management > Error Disable to access this screen. GS1900 Series User’s Guide...
Page 92 This field displays the supported features that allow the Switch to shut down a port or Reason discard packets on a port according to the feature requirements and what action you configure. Time Left (sec) This field displays the time left in seconds. Action This field displays the action. GS1900 Series User’s Guide...
Page 93: Configuration: System
17.2.1 The IPv4 Screen Use this screen to view the IPv4 interface status and Switch’s management IPv4 addresses. Click Configuration > System > IP > IPv4 to open this screen. Figure 85 Configuration > System > IP > IPv4 GS1900 Series User’s Guide...
Page 94: The Ipv6 Screen
Select Enable to allow the device to act as a DHCPv6 client or Disable to disallow it. This field displays the Switch’s DHCP settings when it is acting as a DHCPv6 client. Auto Select Enable to allow the device to auto-configure the IPv6 properties or Disable to Configuration manually enter the properties. GS1900 Series User’s Guide...
Page 95: Time
Select the system date and time values from the dropdown lists. Time Zone Select the time zone from the dropdown list. Daylight Saving Select Enable to use Daylight Saving Time to offset the system time or Disable not adjust Time system time. GS1900 Series User’s Guide...
Page 96: The Sntp Server Screen
Apply Click Apply to save the changes. Cancel Click Cancel to discard the changes. 17.4 Information The information option is used to set the following system information properties: system name, system location, and system contact information. GS1900 Series User’s Guide...
Page 97: The System Information Screen
Enter the geographic location of the Switch for identification purposes. System Contact Enter the person in charge of the Switch for identification purposes. Apply Click Apply to save the changes. Cancel Click Cancel to discard the changes. GS1900 Series User’s Guide...
Page 98: Configuration: Port
18.2 Port Use this screen to view Switch port settings and select ports for configuration. Click Configuration > Port > Port > Port to open this screen. Figure 90 Configuration > Port > Port > Port GS1900 Series User’s Guide...
Page 99: The Port Edit Screen
18.2.1 The Port Edit Screen Use this screen to configure Switch port settings. Click Configuration > Port > Port > Edit to open this screen. Figure 91 Configuration > Port > Port > Edit GS1900 Series User’s Guide...
Page 100: Eee
Use this screen to view Switch port Energy-Efficient Ethernet (EEE) settings and select ports for configuration. Click Configuration > Port > EEE > EEE to open this screen. Figure 92 Configuration > Port > EEE > EEE GS1900 Series User’s Guide...
Page 101: The Eee Edit Screen
Ethernet ports, and each device that receives power through an Ethernet port is a Powered Device (PD). Use this screen to view Switch port Power over Ethernet (PoE) settings and select ports for configuration. Click Configuration > Port > PoE > PoE to open this screen. GS1900 Series User’s Guide...
Page 102 Class 3 - Optional, 6.49 to 12.95 • Class 4 - Reserved (PSEs classify as Class 0) in a switch that supports IEEE 802.3af only. Optional, 12.95 to 25.50 in a switch that supports IEEE 802.3at. GS1900 Series User’s Guide...
Page 103: The Poe Edit Screen
Displays the list of port index numbers that are being configured. PD State Select Enable to provide power to a PD connected to the port or Disable so the port cannot receive power from the Switch. GS1900 Series User’s Guide...
Page 104 Select Low to set the Switch to assign the remaining power to the port after all critical and high priority ports are served. Apply Click Apply to save the changes. Cancel Click Cancel to discard the changes. GS1900 Series User’s Guide...
Page 105: Bandwidth Management
Specify the current egress burst size in bytes for all ports. Burst Port Rate Edit Select this check box to configure the properties of a port. Click the Edit button change the properties of the port. GS1900 Series User’s Guide...
Page 106: The Port Rate Edit Screen
Select Enable to activate egress peak rate limits on the port(s). Egress Enter the maximum bandwidth allowed in kilobits per second (Kbps) for the outgoing traffic Bandwidth flow on a port. (Kbps) Apply Click Apply to save the changes. Cancel Click Cancel to discard the changes. GS1900 Series User’s Guide...
Page 107: Storm Control
Displays how many unicast packets the port receives per second. Unicast (pps) Action Displays the action the device takes when a limit is reached. The following options are available: • Drop - drop the packet. • Shutdown - shutdown the connection. GS1900 Series User’s Guide...
Page 108: The Port Edit Screen
Click the Enable checkbox to active the feature. Unicast (pps) Enter the maximum number of unicast packets the port can receive per second. Apply Click Apply to save the changes. Cancel Click Cancel to discard the changes. GS1900 Series User’s Guide...
Page 109: Configuration: Vlan
The Guest VLAN screen (Section 19.3 on page 115) displays the global and port settings of the Switch. • The Voice VLAN screen (Section 19.4 on page 117) displays the global, OUI, and port settings of the Switch. GS1900 Series User’s Guide...
Page 110: Vlan
19.2.2 The VLAN Add Screen Use this screen to add a VLAN. Click Configuration > VLAN > VLAN > VLAN > Add to open this screen. Figure 101 Configuration > VLAN > VLAN > VLAN > Add GS1900 Series User’s Guide...
Page 111: The Port Screen
19.2.3 The Port Screen Use this screen to view port settings and select VLANs for configuration. Click Configuration > VLAN > VLAN > Port to open this screen. Figure 102 Configuration > VLAN > VLAN > Port GS1900 Series User’s Guide...
Page 112: The Port Edit Screen
Table 71 Configuration > VLAN > VLAN > Port > Edit LABEL DESCRIPTION Port Port Select Displays the list of port index numbers that are being configured. PVID Enter a number between 1 and 4094 as the port VLAN ID. GS1900 Series User’s Guide...
Page 113: The Vlan Port Screen
Port-based VLANs are specific only to the Switch on which they were created. Use this screen to view VLAN port settings. Click Configuration > VLAN > VLAN > VLAN Port to open this screen. GS1900 Series User’s Guide...
Page 114 Select Tagged to set the port TX tag status to tagged in the VLAN. Select Untagged to set the port TX tag status to untagged in the VLAN. Apply Click Apply to save the changes. Cancel Click Cancel to discard the changes. GS1900 Series User’s Guide...
Page 115: Guest Vlan
Figure 106 Configuration > VLAN > Guest VLAN > Global The following table describes the labels in this screen. Table 73 Configuration > VLAN > Guest VLAN > Global LABEL DESCRIPTION Global State Select to enable the global Guest VLAN feature. GS1900 Series User’s Guide...
Page 116: The Port Screen
Display the state of the selected port. 19.3.3 The Port Edit Screen Use this screen to configure the guest VLAN port EEE settings. Click Configuration > VLAN > Guest VLAN > Port > Edit to open this screen. GS1900 Series User’s Guide...
Page 117: Voice Vlan
Use this screen to view and configure voice VLAN settings. 19.4.1 The Global Screen Use this screen to configure the global Voice VLAN settings. Click Configuration > VLAN > Voice VLAN > Global to open this screen. GS1900 Series User’s Guide...
Page 118: The Oui Screen
Use this screen to view the OUI settings. The maximum number of entries is 16. Modifying the OUI table will restart auto detection of OUI process. Click Configuration > VLAN > Voice VLAN > OUI to open this screen. GS1900 Series User’s Guide...
Page 119: The Oui Add/Edit Screen
19.4.3 The OUI Add/Edit Screen Use this screen to add/edit an OUI address. Click Configuration > VLAN > Voice VLAN > OUI > Add/Edit to open this screen. Figure 111 Configuration > VLAN > Voice VLAN > OUI > Add/Edit GS1900 Series User’s Guide...
Page 120: The Port Screen
The following table describes the labels in this screen. Table 79 Configuration > VLAN > Voice VLAN > Port LABEL DESCRIPTION Port Edit Select this check box to configure the properties of a port. Click the Edit button change the properties of the port. GS1900 Series User’s Guide...
Page 121: The Port Edit Screen
MAC addresses in the Voice VLAN will be blocked for 10 seconds. Possible port modes are: • Enabled: Enable Voice VLAN security mode operation. • Disabled: Disable Voice VLAN security mode operation. Apply Click Apply to save the changes. Cancel Click Cancel to discard the changes. GS1900 Series User’s Guide...
Page 122: Configuration: Mac Table
LABEL DESCRIPTION Static MAC Click Add to create a new Static MAC entry. MAC Address Displays the object MAC address from which this incoming frame came. VLAN Displays the VLAN group to which this frame belongs. GS1900 Series User’s Guide...
Page 123: The Static Mac Add Screen
Click Cancel to discard the changes. 20.2.3 The Filtering MAC Screen Use this screen to view Filtering MAC addresses. Click Configuration > MAC Table > Filtering MAC to open this screen. Figure 116 Configuration > MAC Table > Filtering MAC GS1900 Series User’s Guide...
Page 124: The Filtering Mac Add Screen
Use this screen to enter the Dynamic MAC Age. The dynamic MAC age is how long all dynamically learned MAC addresses remain in the MAC address table before they age out (and must be relearned). Click Configuration > MAC Table > Dynamic Age to open this screen. GS1900 Series User’s Guide...
Page 125 Dynamic MAC Age Aging Time Enter the aging time of the MAC address. The value can be between 10 and 630 seconds. Apply Click Apply to save the changes. Cancel Click Cancel to discard the changes. GS1900 Series User’s Guide...
Page 126: Configuration: Link Aggregation
This ensures increased network stability and control over the trunk groups on your Switch. 21.2.1 The Global Screen Use this screen to configure global Link Aggregation settings. Click Configuration > Link Aggregation > Global to open this screen. GS1900 Series User’s Guide...
Page 127: The Lag Management Screen
Click Cancel to discard the changes. 21.2.2 The LAG Management Screen Use this screen to view LAG management settings. Click Configuration > Link Aggregation > LAG Management to open this screen. Figure 120 Configuration > Link Aggregation > LAG Management GS1900 Series User’s Guide...
Page 128: The Lag Add Screen
21.2.3 The LAG Add Screen Use this screen to add a LAG. Click Configuration > Link Aggregation > LAG Management > Add to open this screen. Figure 121 Configuration > Link Aggregation > LAG Management > Add GS1900 Series User’s Guide...
Page 129: The Lag Port Screen
100M, 10M, 100M, or 1000M. Duplex Displays the duplex value as Full, Half, or Auto. FlowCtrl State Displays whether flow control is Enable/Disable. FlowCtrl Status Displays whether flow control is in use (Enable) or not (Disable). GS1900 Series User’s Guide...
Page 130: The Lag Port Edit Screen
Click Apply to save the changes. Cancel Click Cancel to discard the changes. 21.2.6 The LACP Port Screen Use this screen to view LACP Port settings. Click Configuration > Link Aggregation > LACP Port to open this screen. GS1900 Series User’s Guide...
Page 131: The Lacp Port Edit Screen
21.2.7 The LACP Port Edit Screen Use this screen to edit a LACP Port. Click Configuration > Link Aggregation > LACP Port > Edit to open this screen. Figure 125 Configuration > Link Aggregation > LACP Port > Edit GS1900 Series User’s Guide...
Page 132 Enter a value for the port priority. The number can be between 1 and 65,535. Timer Select a timer value of either 1 second or 30 seconds. Apply Click Apply to save the changes. Cancel Click Cancel to discard the changes. GS1900 Series User’s Guide...
Page 133: Configuration: Loop Guard
Figure 126 Configuration > Loop Guard The following table describes the labels in this screen. Table 93 Configuration > Loop Guard LABEL DESCRIPTION Global State Select Enable to activate loop protection on this switch. GS1900 Series User’s Guide...
Page 134: The Loop Guard Port
Displays the action to take by the Switch. The options are Log, Shutdown Port, and Shutdown and Log. 22.2.3 The Port Edit Screen Use this screen to configure a Loop Guard port. Click Configuration > Loop Guard > Port > Edit to open this screen. GS1900 Series User’s Guide...
Page 135 Displays the list of port index numbers to be configured. State Select Enable to use the Admin Enabled feature. Action Select the action to take by the Switch. Apply Click Apply to save the changes. Cancel Click Cancel to discard the changes. GS1900 Series User’s Guide...
Page 136: Configuration: Mirror
The Switch supports local port mirroring. 23.2.1 The Mirror Screen Use this screen to configure Mirroring. Click Configuration > Mirror to open this screen. Figure 129 Configuration > Mirror GS1900 Series User’s Guide...
Page 137 Click > to move a severity type to the acting box from the available box. < Click < to move a severity type from the acting box to the available box. Apply Click Apply to save the changes. Cancel Click Cancel to discard the changes. GS1900 Series User’s Guide...
Page 138: Configuration: Multicast
The following table describes the labels in this screen. Table 97 Configuration > Multicast > IGMP LABEL DESCRIPTION IGMP Global Snooping Status Select Enable to turn on IGMP packet snooping or Disable to turn snooping off. GS1900 Series User’s Guide...
Page 139: The Vlan Screen
Last Member Query Count Displays the number of queries. Interval (sec) Displays the amount of time (in milliseconds) between the IGMP group-specific queries sent by an upstream port when an IGMP Done message is received. Querier GS1900 Series User’s Guide...
Page 140: The Edit Igmp Screen
The value can be between 30 and 18000. Max. Response Enter the amount of time (in seconds) the router connected to the upstream port waits for Interval (sec) a response to an IGMP general query message. GS1900 Series User’s Guide...
Page 141: The Router Port Screen
Click Delete to remove the entry. 24.2.5 The Add/Edit Router Port Screen Use this screen to configure the Router Port settings. Click Configuration > Multicast > IGMP > Router Port > Add/Modify to open this screen. GS1900 Series User’s Guide...
Page 142: The Profile Screen
Click Apply to save the changes. Cancel Click Cancel to discard the changes. 24.2.6 The Profile Screen Use this screen to view the IGMP Profile settings. Click Configuration > Multicast > IGMP > Profile to open this screen. GS1900 Series User’s Guide...
Page 143: The Add/Edit Profile Screen
Figure 136 Configuration > Multicast > IGMP > Profile > Add/Modify The following table describes the labels in this screen. Table 103 Configuration > Multicast > IGMP > Profile > Add/Modify LABEL DESCRIPTION IGMP Profile Profile No. Enter the Profile No. GS1900 Series User’s Guide...
Page 144: The Throttling Screen
Filter Profile ID Displays the throttling filter profile ID. 24.2.9 The Add/Edit Throttling Screen Use this screen to configure the Throttling settings. Click Configuration > Multicast > IGMP > Throttling > Add/Edit to open this screen. GS1900 Series User’s Guide...
Page 145 Select the action taken by the groups to be Deny or Replace. Number Action Filter Profile ID Select the throttling filter profile ID from the dropdown list. Apply Click Apply to save the changes. Cancel Click Cancel to discard the changes. GS1900 Series User’s Guide...
Page 146: Configuration: Spanning Tree
It allows a Switch to interact with other (R)STP-compliant switches in your network to ensure that only one path exists between any two stations on the network. 25.2.1 The Global Screen Use this screen to view the Global settings. Click Configuration > Spanning Tree to open this screen. GS1900 Series User’s Guide...
Page 147: The Stp Port Screen
Click Apply to save the changes. Cancel Click Cancel to discard the changes. 25.2.2 The STP Port Screen Use this screen to view the STP Port settings. Click Configuration > Spanning Tree > STP Port to open this screen. GS1900 Series User’s Guide...
Page 148: The Stp Port Edit Screen
Displays the P2P MAC status as Yes or No. 25.2.3 The STP Port Edit Screen Use this screen to configure the STP Port Edit settings. Click Configuration > Spanning Tree > STP Port > Edit to open this screen. GS1900 Series User’s Guide...
Page 149: The Cist Screen
Click Apply to save the changes. Cancel Click Cancel to discard the changes. 25.2.4 The CIST Screen Use this screen to view the CIST settings. Click Configuration > Spanning Tree > CIST to open this screen. GS1900 Series User’s Guide...
Page 150 This is the time interval in seconds between BPDU (Bridge Protocol Data Units) configuration message generations by the root switch. The allowed range is 1 to 10 seconds. Apply Click Apply to save the changes. Cancel Click Cancel to discard the changes. GS1900 Series User’s Guide...
Page 151: The Cist Port Screen
Displays the internal path cost. Cost 25.2.6 The CIST Port Edit Screen Use this screen to configure the CIST Port Edit settings. Click Configuration > Spanning Tree > CIST Port > Edit to open this screen. GS1900 Series User’s Guide...
Page 152: The Mst Screen
Table 112 Configuration > Spanning Tree > MST LABEL DESCRIPTION MST Instance Click Add to create a new MST Instance entry. MSTI Displays the Multiple Spanning Tree Instance(s) (MSTI). VLAN List Display a list of MSTI VLANs. GS1900 Series User’s Guide...
Page 153: The Add/Modify Mst Screen
Click Apply to save the changes. Cancel Click Cancel to discard the changes. 25.2.9 The MST Port Screen Use this screen to view the MST Port settings. Click Configuration > Spanning Tree > MST Port to open this screen. GS1900 Series User’s Guide...
Page 154: The Mst Port Edit Screen
Displays the internal path cost. Cost 25.2.10 The MST Port Edit Screen Use this screen to configure the MST Port Edit settings. Click Configuration > Spanning Tree > MST Port > Edit to open this screen. GS1900 Series User’s Guide...
Page 155 0 and 255 and the default value is 128. Internal Path Enter the internal path cost. Enter 0 for Auto. Cost (0=Auto) Apply Click Apply to save the changes. Cancel Click Cancel to discard the changes. GS1900 Series User’s Guide...
Page 156: Configuration: Lldp
Figure 149 Configuration > LLDP > Global The following table describes the labels in this screen. Table 116 Configuration > LLDP > Global LABEL DESCRIPTION Global State Select Enable to activate the global LLDP. GS1900 Series User’s Guide...
Page 157: The Port Screen
Apply Click Apply to save the changes. Cancel Click Cancel to discard the changes. 26.2.2 The Port Screen Use this screen to view the Port settings. Click Configuration > LLDP > Port to open this screen. GS1900 Series User’s Guide...
Page 158: The Port Edit Screen
MFS - 802.3 Maximum Frame Size • MA - Management Address 26.2.3 The Port Edit Screen Use this screen to configure the Port Edit settings. Click Configuration > LLDP > Port > Edit to open this screen. GS1900 Series User’s Guide...
Page 159: The Local Information Screen
Click Apply to save the changes. Cancel Click Cancel to discard the changes. 26.2.4 The Local Information Screen Use this screen to view the Local Information settings. Click Configuration > LLDP > Local Information to open this screen. GS1900 Series User’s Guide...
Page 160 Displays the chassis ID subtype. Subtype Chassis ID The Chassis ID is the identification of the neighbor's LLDP frames. System Name System Name is the name advertised by the neighbor unit. System Displays the System Description. Description GS1900 Series User’s Guide...
Page 161: The Local Information Edit Screen
ELIN to be used for emergency calling. 26.2.5 The Local Information Edit Screen Use this screen to configure the Port Edit settings. Click Configuration > LLDP > Local Information > Edit to open this screen. GS1900 Series User’s Guide...
Page 162 The following table describes the labels in this screen. Table 120 Configuration > LLDP > Local Information > Edit LABEL DESCRIPTION MED Port Location Port List Displays the index number of the LLDP port(s). The value is made of 16 pairs of hexadecimal characters. GS1900 Series User’s Guide...
Page 163 Room no.: Room number - Example: 450F. • Place type: Place type - Example: Office. • Postal community name: Postal community name - Example: Leonia. • P.O. Box: Post office box (P.O. BOX) - Example: 12345. GS1900 Series User’s Guide...
Page 164: The Med Network Policy Screen
Click Delete to remove the entry. 26.2.7 The MED Network Policy Add/Edit Screen Use this screen to configure the Port Edit settings. Click Configuration > LLDP > MED Network Policy > Add/Edit to open this screen. GS1900 Series User’s Guide...
Page 165 TCP with buffering would not be an intended use of this application type. 8. Video Signalling - for use in network topologies that require a separate pol- icy for the video signalling than for the video media. GS1900 Series User’s Guide...
Page 166: The Med Port Screen
Select this check box to configure the properties of a port. Click the Edit button change the properties of the port. Port Displays the MED Port value. State Displays the state of the MED port as Enable or Disable. Network Policy Displays the Network Policy value. GS1900 Series User’s Guide...
Page 167: The Med Port Add/Edit Screen
Select one or more of the MED Optional TLVs: TLVs • Network Policy • Location • PoE PSE • Inventory MED Network Select one or more of the MED Network Policies in Available and move them to Acting Policy to activate. GS1900 Series User’s Guide...
Page 168 Chapter 26 Configuration: LLDP Table 124 Configuration > LLDP > MED Port > Edit (continued) LABEL DESCRIPTION Apply Click Apply to save the changes. Cancel Click Cancel to discard the changes. GS1900 Series User’s Guide...
Page 169: Configuration: Qos
27.2.1 The Port Screen Use this screen to view the Port settings. Click Configuration > QoS > General to open this screen. Figure 158 Configuration > QoS > General GS1900 Series User’s Guide...
Page 170: The Port Edit Screen
Select Enable to activate CoS Remark. DSCP Remark Select Enable to activate DSCP Remark. IP Precedence Select Enable to activate IP Precedence Remark. Remark Apply Click Apply to save the changes. Cancel Click Cancel to discard the changes. GS1900 Series User’s Guide...
Page 171: The Queue Screen
Click Apply to save the changes. Cancel Click Cancel to discard the changes. 27.2.4 The CoS Mapping Screen Use this screen to configure the Cos Mapping settings. Click Configuration > QoS > General > CoS Mapping to open this screen. GS1900 Series User’s Guide...
Page 172 Displays a listing of the Queue ID, range: 0 - 7. Class of Service (CoS) (0-7) Click the drop-down menu to map the Queue ID to a specific CoS. Apply Click Apply to save the changes. Cancel Click Cancel to discard the changes. GS1900 Series User’s Guide...
Page 173: The Dscp Mapping Screen
Queue ID Displays the DSCP Queue ID value. Queue to DSCP Mapping DSCP (0-63) Select the DSCP mapping value from the dropdown list. Apply Click Apply to save the changes. Cancel Click Cancel to discard the changes. GS1900 Series User’s Guide...
Page 174: The Ip Precedence Mapping Screen
IP Precedence to Queue Mapping IP Precedence Displays a listing of IP Precedence, range: 0 - 7. Queue ID (0-7) Click the drop-down menu to map an IP Precedence designation to a specific Queue ID (0 - GS1900 Series User’s Guide...
Page 175: Trust Mode
Click Apply to save the changes. Cancel Click Cancel to discard the changes. 27.3.2 The Port Screen Use this screen to view the Port settings. Click Configuration > QoS > Trust Mode > Port to open this screen. GS1900 Series User’s Guide...
Page 176: The Trust Mode Edit Screen
Displays the Trust status as Trust or Untrust. 27.3.3 The Trust Mode Edit Screen Use this screen to configure the Trust Mode settings. Click Configuration > QoS > Trust Mode > Port > Edit to open this screen. GS1900 Series User’s Guide...
Page 177 QoS Port Trust Edit Port List Displays the port index value(s). Mode Select the Trust Mode for the QoS port list as Trust or Untrust. Apply Click Apply to save the changes. Cancel Click Cancel to discard the changes. GS1900 Series User’s Guide...
Page 178: Configuration: Security
Click Apply to save the changes. Cancel Click Cancel to discard the changes. 28.2.2 The Port Screen Use this screen to view the Port settings. Click Configuration > Security > Port Security > Port to open this screen. GS1900 Series User’s Guide...
Page 179: The Port Edit Screen
Action Displays the Action as Discard or Shutdown. 28.2.3 The Port Edit Screen Use this screen to configure the Port settings. Click Configuration > Security > Port Security > Port > Edit to open this screen. GS1900 Series User’s Guide...
Page 180: Protected Port
Click Apply to save the changes. Cancel Click Cancel to discard the changes. 28.3 Protected Port 28.3.1 The Protected Port Screen Use this screen to view the Port settings. Click Configuration > Security > Protected Port to open this screen. GS1900 Series User’s Guide...
Page 181: The Protected Port Edit Screen
Figure 171 Configuration > Security > Port Security > Port > Edit The following table describes the labels in this screen. Table 138 Configuration > Security > Port Security > Port > Edit LABEL DESCRIPTION Protected Port Port List Displays the port list index value(s). GS1900 Series User’s Guide...
Page 182: 182
Click Apply to save the changes. Cancel Click Cancel to discard the changes. 28.4.2 The Port Screen Use this screen to view the Port settings. Click Configuration > Security > 802.1X > Port to open this screen. GS1900 Series User’s Guide...
Page 183: The Port Edit Screen
Click Apply to save the changes. Cancel Click Cancel to discard the changes. 28.4.3 The Port Edit Screen Use this screen to configure the Port settings. Click Configuration > Security > 802.1X > Port > Edit to open this screen. GS1900 Series User’s Guide...
Page 184: Dos
Click Apply to save the changes. Cancel Click Cancel to discard the changes. 28.5 DoS 28.5.1 The Global Screen Use this screen to view the Global settings. Click Configuration > Security > DoS > Global to open this screen. GS1900 Series User’s Guide...
Page 185: The Port Screen
The following table describes the labels in this screen. Table 143 Configuration > Security > DoS > Port LABEL DESCRIPTION Port Edit Select this check box to configure the properties of a port. Click the Edit button change the properties of the port. GS1900 Series User’s Guide...
Page 186: The Port Edit Screen
Table 144 Configuration > Security > DoS > Port > Edit LABEL DESCRIPTION Port Port List Displays the port index value. State Select Enable to activate the port’s DoS feature. Apply Click Apply to save the changes. Cancel Click Cancel to discard the changes. GS1900 Series User’s Guide...
Page 187: Configuration: Aaa
Displays the authentication method name. The name can be between 1 and 31 ASCII Alphanumeric Characters. Method List Displays the list of authentication methods as being Local or Radius or TACACS+. Modify Click the Modify button to change the configuration settings for a VLAN entry. GS1900 Series User’s Guide...
Page 188: The Auth Method Add/Modify Screen
Click Apply to save the changes. Cancel Click Cancel to discard the changes. 29.3 RADIUS 29.3.1 The RADIUS Screen Use this screen to configure the RADIUS settings. Click Configuration > AAA > RADIUS to open this screen. GS1900 Series User’s Guide...
Page 189: The Radius Add/Modify Screen
Click to Edit modify the entry. Modify Click Delete to delete the entry. 29.3.2 The RADIUS Add/Modify Screen Use this screen to configure the RADIUS settings. Click Configuration > AAA > RADIUS > Add/ Modify to open this screen. GS1900 Series User’s Guide...
Page 190: Tacacs
Click Apply to save the changes. Cancel Click Cancel to discard the changes. 29.4 TACACS+ 29.4.1 The TACACS+ Screen Use this screen to configure the TACACS+ settings. Click Configuration > AAA > TACACS+ to open this screen. GS1900 Series User’s Guide...
Page 191: The Tacacs+ Add/Modify Screen
Click Delete to delete the entry. 29.4.2 The TACACS+ Add/Modify Screen Use this screen to configure the TACACS+ settings. Click Configuration > AAA > TACACS+ > Add/Modify to open this screen. Figure 183 Configuration > AAA > TACACS+ > Add/Modify GS1900 Series User’s Guide...
Page 192 Enter the number of time outs for replies. The value can be between 1 and 30 seconds. Reply Priority Select the server priority as High or Low. Apply Click Apply to save the changes. Cancel Click Cancel to discard the changes. GS1900 Series User’s Guide...
Page 193: Configuration: Management
The following table describes the labels in this screen. Table 151 Configuration > Management > Syslog LABEL DESCRIPTION Global State Select the global logging setting to be enabled or disabled. Apply Click Apply to save the changes. Cancel Click Cancel to discard the changes. GS1900 Series User’s Guide...
Page 194: The Local Screen
The following table describes the labels in this screen. Table 153 Configuration > Management > Syslog > Local > Add/Modify LABEL DESCRIPTION Local Add Target Select the local storage target for logging messages. The options are Buffered or Flash. GS1900 Series User’s Guide...
Page 195: The Remote Screen
Click Edit to make changes to the entry. Delete Click Delete to remove the entry. 30.2.5 The Remote Add/Modify Screen Use this screen to configure the Remote settings. Click Configuration > Management > Syslog > Remote > Add/Modify to open this screen. GS1900 Series User’s Guide...
Page 196: Snmp
XGS3700 Series User’s Guide SNMP version 3. The next figure illustrates an SNMP management operation. SNMP is only available if TCP/IP is configured. 30.3.1 The Global Screen Use this screen to view the Global settings. Click Configuration > Management > SNMP to open this screen. GS1900 Series User’s Guide...
Page 197: The Community Screen
1 to 20, and the allowed content is ASCII characters from 33 to 126. Access Right Displays the access mode for this entry. The possible values are Read-Only and Read- Write. Modify Edit Click Edit to make changes to the entry. Delete Click Delete to remove the entry. GS1900 Series User’s Guide...
Page 198: The Community Add/Modify Screen
Figure 192 Configuration > Management > SNMP > Group The following table describes the labels in this screen. Table 159 Configuration > Management > SNMP > Group LABEL DESCRIPTION SNMPv3 Group Click Add to create a new SNMPv3 Group entry. GS1900 Series User’s Guide...
Page 199: The Group Add/Modify Screen
NoAuth, NoPriv: No authentication and no privacy. • Auth, NoPriv: Authentication and no privacy. • Auth, Priv: Authentication and privacy. Access Right Select the access mode for this entry. The possible values are Read-Only and Read- Write. GS1900 Series User’s Guide...
Page 200: The User Screen
Write. Action Delete Click Delete to remove the entry. 30.3.7 The User Add/Modify Screen Use this screen to configure the User settings. Click Configuration > Management > SNMP > User > Add/Modify to open this screen. GS1900 Series User’s Guide...
Page 201: The Trap Screen
Click Apply to save the changes. Cancel Click Cancel to discard the changes. 30.3.8 The Trap Screen Use this screen to configure the Trap settings. Click Configuration > Management > SNMP > Trap to open this screen. GS1900 Series User’s Guide...
Page 202: The Trap Destination Screen
30.3.9 The Trap Destination Screen Use this screen to view the Trap Destination settings. Click Configuration > Management > SNMP > Trap Destination to open this screen. Figure 197 Configuration > Management > SNMP > Trap Destination GS1900 Series User’s Guide...
Page 203: The Trap Destination Add/Modify Screen
Select the SNMP trap supported version. Possible versions are: • SNMP v1: Set SNMP trap supported version 1. • SNMP v2c: Set SNMP trap supported version 2c. • SNMP v3: Set SNMP trap supported version 3. GS1900 Series User’s Guide...
Page 204: Error Disable
Select an option to Enable or Disable the Unknown Multicast Flood. Multicast Flood Unicast Flood Select an option to Enable or Disable the Unicast Flood. Port Security Select an option to Enable or Disable the Port Security. GS1900 Series User’s Guide...
Page 205: Http/Https
Select the authentication method from the dropdown list. Method Session Timeout Enter the session timeout value. The timeout can be between 0 and 86400 minutes. Apply Click Apply to save the changes. Cancel Click Cancel to discard the changes. GS1900 Series User’s Guide...
Page 206: The Https Screen
Click Apply to save the changes. Cancel Click Cancel to discard the changes. 30.6 Users 30.6.1 The Users Screen Use this screen to configure the Users settings. Click Configuration > Management > Users to open this screen. GS1900 Series User’s Guide...
Page 207: The Users Add/Modify Screen
Click Edit to make changes to the entry. 30.6.2 The Users Add/Modify Screen Use this screen to configure the Users settings. Click Configuration > Management > Users > Add/Modify to open this screen. Figure 203 Configuration > Management > Users > Add/Modify GS1900 Series User’s Guide...
Page 208: Remote Access Control
30.7 Remote Access Control 30.7.1 The Global Screen Use this screen to configure the Global settings. Click Configuration > Management > Remote Access Control to open this screen. Figure 204 Configuration > Management > Remote Access Control GS1900 Series User’s Guide...
Page 209: The Profile Add/Modify Screen
Delete Click Delete to remove the entry. 30.7.2 The Profile Add/Modify Screen Use this screen to configure the Profile settings. Click Configuration > Management > Remote Access Control > Profile > Add/Modify to open this screen. GS1900 Series User’s Guide...
Page 210 Select and enter the IPv4/Wildcard source. Service Select the service to use for remote access. The values are ALL, HTTP, HTTPS, or SNMP. Apply Click Apply to save the changes. Cancel Click Cancel to discard the changes. GS1900 Series User’s Guide...
Page 211: Maintenance
Choose Backup to upload the firmware file as the backup image. Alternatively, choose Active to upload the firmware file as the active image. Browse File Browse to the path on your computer where the firmware you want to upload to be the active image is kept. GS1900 Series User’s Guide...
Page 212: Upgrade The Firmware From A File On Your Computer
Switch. Active and backup firmware versions are saved as images on flash partitions. The backup image is used when the active partition has problems during boot. From the Maintenance screen, display the Firmware Management screen as shown next. Use this screen to view image information and activate an image. GS1900 Series User’s Guide...
Page 213: Activate The Backup Image
Click Cancel to discard the changes. 31.3 Backup a Configuration File 31.3.1 Overview You can save various “snapshots” of your device to the server or your computer and restore them at a later date, if required. GS1900 Series User’s Guide...
Page 214: Back Up Configuration Or Log Files To A Server
4. Click Apply to save a snapshot of your current configuration to the TFTP server. Click Cancel to discard the changes. 31.3.3 Back up configuration or log files to your computer Follow the steps below to backup configuration or log files to your computer. GS1900 Series User’s Guide...
Page 215: Restore A Configuration File
Follow the steps below to restore the configuration from a server. 1. In Method, choose TFTP. 2. In Server IP, enter the TFTP server IP address. 3. In File Name, enter the name of the configuration file on the TFTP server. GS1900 Series User’s Guide...
Page 216: Restore The Configuration From A File On Your Computer
1. In Source File, select the file to be used as a reference. 2. In Destination File, select the file to be overwritten. 3. Click Apply to restore to overwrite the destination file with the source file. Click Cancel to discard the changes. GS1900 Series User’s Guide...
Page 217: Reset To Factory Defaults
Use the network utilities to perform diagnostics. 31.7.1 Port Test Click Maintenance > Diagnostics > Port Test in the navigation panel to open this screen. Use this screen to perform an internal loopback test on an ethernet port. GS1900 Series User’s Guide...
Page 218: Ipv4 Ping Test
Enter the time in seconds between sending ping packets. The range is 1 to 5 seconds; the default is 1 second. Size Enter the individual packet size in bytes. The range is 8 to 5120 bytes; the default is 56 bytes. GS1900 Series User’s Guide...
Page 219: Ipv6 Ping Test
Follow the steps to perform a ping test. 1. In IP Address, enter the IPv6 address. 2. In Count, enter the number of ping packets. 3. In Interval, enter the time interval in seconds. 4. In Size, enter the packet size in bytes GS1900 Series User’s Guide...
Page 220: Trace Route
1. In IP Address, enter the IPv6 address. 2. In Hops, enter the number of hops. 3. Click Apply to perform the test. Click Cancel to discard the changes. The test results are displayed in Result. GS1900 Series User’s Guide...
Page 221: Reboot
Follow the steps below to restart the Switch. 1. Click Reboot. 2. Click OK and then wait for the Switch to restart. This process takes up to two minutes and does not affect the Switch’s configuration. Click Cancel to discard the changes. GS1900 Series User’s Guide...
Page 222: Troubleshooting
Turn the Switch off and on (in DC models or if the DC power supply is connected in AC/DC models). Disconnect and re-connect the power adaptor or cord to the Switch (in AC models or if the AC power supply is connected in AC/DC models). If the problem continues, contact the vendor. GS1900 Series User’s Guide...
Page 223: Switch Access And Login
If this does not work, you have to reset the device to its factory defaults. See Section 31.6 on page 217. I cannot see or access the Login screen in the web configurator. Make sure you are using the correct IP address. • The default in-band IP address is 192.168.1.1. GS1900 Series User’s Guide...
Page 224 Pop-up Windows, JavaScripts and Java Permissions In order to use the web configurator you need to allow: • Web browser pop-up windows from your device. • JavaScripts (enabled by default). • Java permissions (enabled by default). GS1900 Series User’s Guide...
Page 225: Switch Configuration
Click Save at the top right corner of the web configurator to save the configuration permanently. See also Section 4.3.1 on page 32 for more information about how to save your configuration. GS1900 Series User’s Guide...
Page 226: Appendix A Legal Information
The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of ZyXEL Communications Corporation. Published by ZyXEL Communications Corporation. All rights reserved.
Page 227 Your product is marked with this symbol, which is known as the WEEE mark. WEEE stands for Waste Electronics and Electrical Equipment. It means that used electrical and electronic products should not be mixed with general waste. Used electrical and electronic equipment should be treated separately. GS1900 Series User’s Guide...
Page 228: Index
52, 94, 95, 99, 100, 101, 102, IPv6 103, 106, 117 Neighbor Discovery Protocol disclaimer ping domain name 52, 94, 95, 99, 100, 101, 102, 103, 106, Java permissions Ethernet ports default settings JavaScripts FCC interference statement LEDs Firefox logout GS1900 Series User’s Guide...
Page 229 93, 94, 122, 133, 134, 136, 138, 139, 146, 147, 156, 157, 169, 171, 175, 187, 188, users 190, 193, 196, 204, 205, 206, 208 currently logged in pop-up windows power module disconnecting GS1900 Series User’s Guide...
Page 230 Index ventilation holes VLAN, protocol based, See protocol based VLAN wall mounting warranty note Web Configurator access requirements supported browsers web configurator GS1900 Series User’s Guide...

ZyXEL Communications GS1900 Series User Manual

Contents Overview

Table of Contents

User's Guide

PART I User's Guide

Chapter 1 Getting to Know Your Switch

Chapter 2 Hardware Installation and Connection

Chapter 3 Hardware Overview

Chapter 4 The Web Configurator

Chapter 5 Getting Start

Technical Reference

Part II: Technical Reference

Chapter 6 Monitor: System

Chapter 7 Monitor: Port

Chapter 8 Monitor: VLAN

Chapter 9 Monitor: MAC Table

Chapter 10 Monitor: Link Aggregation

Chapter 11 Monitor: Loop Guard

Chapter 12 Monitor: Multicast

Chapter 13 Monitor: Spanning Tree

Chapter 14 Monitor: LLDP

Chapter 15 Monitor: Security

Chapter 16 Monitor: Management

Chapter 17 Configuration: System

Chapter 18 Configuration: Port

Chapter 19 Configuration: VLAN

Chapter 20 Configuration: MAC Table

Chapter 21

Configuration: Link Aggregation

Chapter 22 Configuration: Loop Guard

Chapter 23 Configuration: Mirror

Chapter 24 Configuration: Multicast

Chapter 25 Configuration: Spanning Tree

Chapter 26 Configuration: LLDP

Chapter 27 Configuration: Qos

Chapter 28 Configuration: Security

Chapter 29 Configuration: AAA

Chapter 30 Configuration: Management

Quick Links

Related Manuals for ZyXEL Communications GS1900 Series

Summary of Contents for ZyXEL Communications GS1900 Series