Canon i-SENSYS MF4300dn Service Manual page 151

Error Code Description
0069 Capability no match paper size after received is DCS signal.
0070 User press stop key within receiving.
0071 Memory full within receiving.
0080 Can't detect any G3 signal within 35 sec. specified by ITU-T in phase B.
0081 Received DTC signal in transmission phase.
0082 Transmitting unit receives a signal other than DIS or DTC. And DCN in phase B.
0083 Detected FSK signal, but Can't receive any signal within 35 sec.
0084 Detect DCN signal in phase B.
0085 Transmitting unit sending DCS 3 times consecutively, but each time responds with DIS/DTC
0086 Detected responds signal other than DTC,DIS,FTT,DCN or CFR after sending DCS.
0087 Training attempt has failed because speed unit can't adjust to low lower speed.
0088 Received DCN signal after sending out DCS signal
008B Receivers protcol of DIS is received, but it is not compatible with our machine.
008C Remote side or our side not support capability.
008D Receivers protocol of DIS is received, but remote side can't receive document temporary, may because by run out of paper or other reason.
008F Modem not ready to received V.34 data within 6 sec after received CFR signal.
0090 Called side document not ready for our polling.
0091 Can't receive any commabd after send DCN signal 3 times consecutively
0093 Received DCN signal after sending out DCN signal
0094 Time out during transmit ECM frame or RCP command.
0095 Wrong ID number
0096 SUBADDRESS/PASSWORD capability not match in polling Rx mode.
009A Can't detect any signal after sending CI signal.
009D Remote side hang up before V.34 modem enter phase 2 state in V.34 polling Rx.
009E Manual Tx over 15 minutes whin in phase C by non-ECM mode.
00A0 User stop or cancel transmission job.
00A1 Document JAM within transmission
00AE Can't finished V.8 procedure or detect V.21 signal after CM signal
00AF Modem can't enter into control channel after TX side sending out RCP signal
for V34
00B1 Can't finish V.8 procedure or detect V.21 signal after ANSam signal within 35 sec.
00B2 Can't detect phase 2 signal after our side sending CJ signal within 30 sec
00B3 Can't detect correct V.21 or JM signal after sending CM or CJ signal.
00B4 Can't detect correct phase 2 signal within 25 second after CM/JM signal exchange.
00B5 Can't detect phase 3 signal after Phase 2
00B6 Can't detect phase 4 signal within 25 sec after CM/JM exchange.
00B8 Remote side disconnect after our side sending DCS signal in V.34.
00BA Cannot received correct signal after our side sending DTC signal in V.34.
00BB Every time our side received DIS signal after sending DTC in V.34.
00BC Modem can't ready within 10 second after entering primary channel in V.34.
00BD Can't detect correct V.21 or JM signal after detected FSK frequency.
00BE Remote side no document to be polled after V.8 handshaking.
00BF Capability no match after V.8 handshaking
00C1 At phase-D, transmitting units out EOP 3 times consecutively, but receive no answer from receiving unit.
00C2 Remote side disconnect after sending out V.8 CM signal.
00C4 After sending MPS signal, the received is not one of MCF, RTN, PIP, PIN, RTP, DCN.
00C5 Received DCN signal after sending MPS signal.
00C9 At phase D, sending MPS 3 times consecutively, but no answer from receiveing unit.
00CA After sending EOP signal, the received is not one of MCF, RTN, PIP, PIN, PRI-EOP, DCN, RTP.
00CB After sending EOP signal, the received is DCN signal.
Chapter 13
13-3