Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for versa climber VC 108 CM
Summary of Contents for versa climber VC 108 CM
- Page 1 VC 108 CM OPERATIONAL MANUAL MADE IN USA...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Page CALORIE BURN GRAPH ....................3 GENERAL INTRODUCTION....................4 SELECTING EXERCISE TIME...................4 CALORIE BURN RATE.......................4-5 STEPPER USER GUIDE....................5 CLIMBING USER’S GUIDE....................5 MODULE DISPLAY......................5-6-7 SELECTING AN OPPONENT.....................6 SELECTING A LANDMARK....................6 USING HYDRAULICS TO CONTROL SPEED..............7 VERSACLIMBER SPECIFICATIONS.................. 8 UNPACKING INSTRUCTIONS...................8 ASSEMBLY INSTRUCTIONS.....................9-12 ASSEMBLY INSTRUCTIONS FOR HIGH-TRI &... -
Page 3: Calorie Burn Graph
Page 3... -
Page 4: General Introduction
NOTE NOTE: Don’t Climb Too Fast. Beginners BEFORE EXERCISING ON THE VERSACLIMBER, READ THIS Should Take a 6 inch Step At a Gentle Pace OPERATION MANUAL THOROUGHLY. INSTRUCT OTHERS HOW TO USE THE MACHINE IN ACCORDANCE WITH THE PROCEDURES OUTLINED IN THIS MANUAL. First time users of the VersaClimber have a tendency ADDITIONAL MANUALS ARE AVAILABLE... -
Page 5: Stepper User Guide
CALORIES ACTIVITY NOTE: WHEN GRASPING THE HAND RAILS OR HAND GRIPS, (For a 150 lb person) Calories Burned KEEP FINGERS AND THUMBS ON THE FOAM PADDING SPEED Per Hour OF THE HANDRAILS OR RUBBER GRIPS OF THE Walking 3.0 mph HANDLES. -
Page 6: Selecting An Opponent
YELLOW QUICK START BUTTON ENTER WEIGHT When pressed, it clears the display of any Press this button to enter your weight which is previous information and verbally guides the used to calculate caloric burn rate. Use the yel- first time user through a 15 minute workout. arrows to raise or lower your LOCK SELECT weight in the display until it matches your weight... -
Page 7: Using Hydraulics To Control Speed
“Lower Right” SELECT button. VersaClimbing uses many more muscles than Press this button to switch between jogging, pedaling , stepping or elliptical exercises OPPONENT’S and is therefore performed at a slower cyclic rate TOTAL DISTANCE OPPONENT’S DISTANCE PER . This button is only active when virtual and speed. -
Page 8: Versaclimber Specifications
VERSACLIMBER SPECIFICATIONS TOOLS REQUIRED FOR ASSEMBLY OF A SINGLE UNIT: A. –One screw driver (Flat Head) PHYSICAL SIZE –One Phillips screw driver Height 7 feet, 10 Inches Footprint 43 Inches x 46 Inches B. Two 9/16” wrenches. Weight 155 pounds (70 kg) C. - Page 9 (7) 3/8” Lock Nuts (1) 2 5/8” Hand Rail Spacer (3) Side hand rails bolts 3/8” x 3 3/4” long Attach the front curved tubular floor brace to the post. Using four hex head bolts, 3/8” x 5/8” long bolts, screw down until firmly tight. (4) Base bolts (2) Base bolts 3/8”...
- Page 10 After tubular brace is in place, go back and FULLY TIGHTEN the two 3 long base bolts. 3/4” Using two people lift and hold VersaClimber in upright position. Then go back and TIGHTEN FULLY the TOP lock nut on the tubular brace. Attach back tubular floor brace to post with two hex head bolts, 3/8”x 3 long.
- Page 11 Attach foot pedals with “L” shape bracket Join left and right hand rails. pointing up, using (2) 3/8” x 1 long hex 1/4” head bolts. Loosely attach two 3/8” lock nuts nearest to the Securely TIGHTEN foot pedals. inside center of machine. Attach side handrails with (3) hex head bolts 4 1/4“...
-
Page 12: Assembly Instructions
(OPTIONAL) ARM EXTENDERS ASSEMBLY INSTRUCTIONS On the standard 108 CM a person up to 6’ 3” tall FOR HIGH-TRI AND HIGH-FIVE has a full arm extension while climbing. With Protect the oil reservoir and the black plastic optional arm extenders a 6’ 9” person gets a full computer housing by supporting the Versa stretch while climbing. -
Page 13: Maintenance Instructions
When climbing, oil passes through the pressure MAINTENANCE INSTRUCTIONS control valve. Closing the valve increases climb- ing resistance and opening the valve decreases The VersaClimber consists of a mainframe that is climbing resistance. supported on a stable 3 point base. A sprocket is attached to a hydraulic pump located at the top of If a large amount of slack (more than 1/2”... -
Page 14: Trouble Shooting
SYMPTOM: CHAIN LUBRICATION ALL ZEROS ARE REGISTERING Lubricate chains every 2,000 hours of operation ON MODULE with light grease. Before lubrication clean the If all zeros register on the display when the chain with paint thinner on a toothbrush and then machine is in motion, there could be a faulty use toothbrush to spread a light coat of grease encoder circuit board, broken or loose wire... - Page 15 SYMPTOM: Write down additional notes here: MACHINE IS “STICKY”, IRREGULAR OR HARD TO MOVE The foot pedals and handgrips are attached to metal bars that move up and down inside C shaped metal channels. The bars have plastic rollers and slides that guide the bars through the channels.
-
Page 16: Spare Parts List
SPARE PARTS LIST In the event that a replacement part is ordered from the factory, Please refer to the following spare parts list for the correct part description and part number. This information will expedite your shipment when calling our Service Department. Electronics CM Module (108/109) . -
Page 17: Limited Warranty
LIMITED WARRANTY 1. Heart Rate Inc. (H.R.I.) warrants to the original purchaser that the VC 108 CM is free from defects in material and workmanship under normal use and proper maintenance with a three year limited warranty subject to the terms and conditions hereafter set forth. -
Page 18: Warranty
5. Length of Warranty, labor During the first year, all labor is covered by the warranty. All labor repairs for warranty and non-warr a n t y parts will be performed at the factory. The cost of shipping to and from the factory is the responsibility of the warranty.