Table of Contents
Advertisement
Quick Links
© 2010 Horizon Hobby, Inc.
4105 Fieldstone Road
Champaign, IL 61822
Horizon Hobby UK
Units 1-4 Ployters Rd
Staple Tye
Harlow, Essex
CM18 7NS
United Kingdom
Horizon Hobby Deutschland GmbH
Hamburger Strasse 10
25335 Elmshorn
E-flite
products are distributed exclusively by Horizon Hobby, Inc.
®
Bell, Huey, and UH-1 Iroquois emblems, logos, and body designs are
trademarks of Textron Innovations Inc. and are used under license by Horizon
Hobby, Inc.
www.E-fliteRC.com
Printed 11/09
USA
Germany
Blade
Assembly Manual
Note: Attempting to fly the helicopter without completely reading the
manual may cause injury to yourself and people in the vicinity, as well
as damaging the helicopter.
16453
UH-1 Huey Body
®
Kit will fit any CP series helicopter.
Advertisement
Table of Contents
Related Manuals for Blade UH-1 Huey Body
Summary of Contents for Blade UH-1 Huey Body
- Page 1 Blade UH-1 Huey Body ® Assembly Manual © 2010 Horizon Hobby, Inc. 4105 Fieldstone Road Champaign, IL 61822 Kit will fit any CP series helicopter. Horizon Hobby UK Units 1-4 Ployters Rd Staple Tye Harlow, Essex Note: Attempting to fly the helicopter without completely reading the...
-
Page 2: Table Of Contents
EFLH1387 ........ -
Page 3: Tools Required
Tools Required 4. Install the 84mm (3.3-inch) long carbon rods between the front 1.5mm hex driver Small Cable Ties and rear landing gear/battery #0 Phillips Screwdriver Thin CA mounting plate. Needle-Nose Pliers Side Cutters Ruler Threadlock Razor Saw Scissors Clear Tape Silicone or Contact Cement Assembly 5. - Page 4 8. Wrap the antenna around the new 10b. Use a razor saw to cut the tail assembly if needed. Leave about boom off of the helicopter at this 250–305mm (10–12 inches) of mark. If you intend to save your old antenna to route through the tail tail motor system you will have to boom section.
- Page 5 13. Mount the LED lights into the body. 16. Mount the tail motor to the tail rotor A flashing red LED is mounted at mount using the 1mm x 3mm (0.03 the top of the body behind the x 0.1-inch) machine screws, washers main shaft and a 6-inch extension and a #0 Phillips screwdriver.
- Page 6 20. Slide the frame into the Huey body 23. Sight down the assembled fuselage from the bottom. Make sure the and make sure the tail rotor mount tail motor mount plugs into the tail is vertical and aligned with the boom during this assembly.
- Page 7 27. Install the tail rotor blade onto the 31. Mount the new main rotor blades hub using a 1.5mm hex driver. Make included with the Huey body. sure the tail rotor is mounted in the correct orientation. 28. Mount the gun pods onto the fuselage.
-
Page 8: Flying And Tuning
EFLH1386 Body Mounts & Gun Pods, Huey: BCP/+/PP/PP2 warranty claims. Further, Horizon reserves the right to change or modify this EFLH1387 Tail Rotor Blade (2) Black, Huey: BCP/+/PP/PP2 warranty without notice and disclaims all other warranties, express or implied. (b) Limitations- HORIZON MAKES NO WARRANTY OR REPRESENTATION,... - Page 9 Non-Warranty Repairs If you as the Purchaser or user are not prepared to accept the liability associated with the use of this Product, you are advised to return this Product Should your repair not be covered by warranty the repair will be completed and immediately in new and unused condition to the place payment will be required without notification or estimate of the expense unless of purchase.
-
Page 10: Compliance Information For The European Union
United Kingdom No. HH2009122401 Electronics and engines requiring inspection or repair should be shipped to the following address: Products: EFL Blade Huey body Item Numbers: EFLH1380 Horizon Hobby UK Units 1-4 Ployters Rd The object of declaration described above is in conformity with the requirements...