Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Blade Fusion 360
Summary of Contents for Blade Fusion 360
- Page 1 Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni...
- Page 2 NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com or www.towerhobbies.com and click on the support or resources tab for this product. Meaning of Special Language The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product: WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage,...
-
Page 3: Table Of Contents
Limited Warranty ..........18 Control Tests ............8 Warranty and Service Contact Information ..19 Pre-Flight Checklist ..........9 FCC Information ..........19 Flying the Blade Fusion 360 .......9 IC Information ...........20 Gyro Gain Adjustment ........10 Compliance Information for the European Union ..20 Tail Belt Tension ..........10 Specifi... -
Page 4: First Flight Preparation
First Flight Preparation Flying Checklist ❏ Always turn the transmitter on fi rst • Remove and inspect contents ❏ Plug the fl ight battery into the lead from the ESC • Begin charging the fl ight battery (not included) ❏ Allow the ESC to initialize and arm properly •... -
Page 5: Transmitter Setup
Transmitter Setup Program your transmitter before attempting to bind or fl y Spektrum ™ transmitters. The fi les for models using Spektrum ™ ™ the helicopter. Always start by creating a new model in the transmitters with Spektrum AirWare software are also transmitter to ensure no existing settings are inadvertently available for download online at www.spektrumrc.com. -
Page 6: Transmitter Setup
Transmitter Setup DX6G2, DX6e, DX7G2, DX8G2, DX8e, DX9, iX12, DX18, DX20 SYSTEM SETUP FUNCTION LIST Servo Setup Model Type HELI Channel Travel Reverse Channel Travel Reverse Swash Type Normal 100/100 Normal 100/100 Normal F-Mode Setup 100/100 Normal AX2* 100/100 Normal Switch 1 Switch B 100/100... -
Page 7: Installing The Flight Battery
Installing the Flight Battery 1. Lower the throttle. 7. Do not move the helicopter until the fl ight controller initializes. The swashplate will center, indicating that 2. Power on the transmitter. the unit is ready. The fl ight controller status LED will 3. -
Page 8: Throttle Hold
Throttle Hold Throttle hold is used to prevent the motor from powering on Throttle hold is also used to turn off the motor quickly if the inadvertently. For safety, turn throttle hold ON any time you helicopter is out of control, in danger of crashing, or both. need to touch the helicopter or check the direction controls. -
Page 9: Pre-Flight Checklist
fl ying. When the helicopter is in stunt mode: The Blade Fusion 360 is intended to be fl own outdoors by • The rotor head speed is constant. experienced pilots. • The main rotor will increase negative pitch as the... -
Page 10: Gyro Gain Adjustment
Gyro Gain Adjustment • If the tail wags or oscillates, lower the gain on the gyro. • If the tail is drifting while hovering, increase the gain on the gyro. In the transmitter gyro menu, decrease the gyro gain In the transmitter gyro menu, increase the gyro gain values a small amount at a time until the helicopter is values a small amount at a time until the tail starts to stable within a particular fl... -
Page 11: Advanced Tuning (Forward Programming)
The Fusion 360 BNF fl ight controller may be programmed from any compatible Spektrum transmitter (visit SpektrumRC.com for more information). The fl ight controller shipped with BNF models has a range of adjustable parameters suitable for the Fusion 360 Helicopter and is not intended for use in other aircraft. -
Page 12: Advanced Tuning (Non-Forward Programming)
Applies to Spektrum transmitters not capable of forward programing including DX6i, DX6e, DX7s DX8, and DX8e Your Blade Fusion 360 was setup at the factory and test For pilots fl ying with a transmitter not capable of forward fl own. The servo adjustment steps are usually only neces-... - Page 13 Calibration Procedure If the helicopter is experiencing drift issues after completing the trim fl ight procedure, perform the following calibration. The calibration procedure may also be needed following crash repairs. To perform the calibration procedure: 1. Ensure the surface used for calibration is level. 6.
-
Page 14: Troubleshooting Guide
Troubleshooting Guide Problem Possible Cause Solution Low fl ight battery or transmitter Fully charge or replace the fl ight battery and/or transmitter battery voltage batteries Power on the transmitter while holding the Trainer/Bind Helicopter will not bind Transmitter is not in bind mode switch. -
Page 15: Exploded View
Exploded View... -
Page 17: Parts List
Bear Block Set (3): Fusion 360 13 BLH5204 Main Rotor Headblock: Fusion 36 35 BLH5226 Tail Rotor Bellcrank: Fusion 360 14 BLH5205 Damper Set (2) 90 : Fusion 360 36 BLH5232 Helical Pinion 12T 15 BLH5206 Swashplate: Fusion 360 37 BLH5337... -
Page 18: Limited Warranty
Limited Warranty What this Warranty Covers questions and service you in the event that you may need any assistance. For questions or assistance, please visit our website Horizon Hobby, LLC, (Horizon) warrants to the original purchaser at www.horizonhobby.com, submit a Product Support Inquiry, or that the product purchased (the “Product”) will be free from call the toll free telephone number referenced in the Warranty defects in materials and workmanship at the date of purchase. -
Page 19: Warranty And Service Contact Information
Sales: Horizon Hobby GmbH +49 (0) 4121 2655 100 FCC Information FCC ID: BRWAR4649T Supplier’s Declaration of Conformity Fusion 360 – BLH5250 Contains IC: 6157A-AR4649T This device complies with part 15 of the FCC FCC Information Rules. Operation is subject to the following This device complies with part 15 of the FCC rules. -
Page 20: Ic Information
IC Information IC: 6157A-AR4649T This device complies with Industry Canada licence-exempt (2) this device must accept any interference, including RSS standard(s). Operation is subject to the following two interference that may cause undesired operation of the conditions: (1) this device may not cause interference, and device.”... - Page 21 ©2019 Horizon Hobby, LLC. Blade, the Blade logo, Fusion, DSM, DSM2, DSMX, Bind-N-Fly, IC3, EC3, AirWare, SAFE, BNF, the BNF logo, ModelMatch and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc.
Need help?
Do you have a question about the Fusion 360 and is the answer not in the manual?
Questions and answers