Table of Contents
Advertisement
DO NOT CONTACT THE STORE!!!
CALL OUR CUSTOMER SERVICE DEPARTMENT
**For customers outside the U.S. or Canada, please contact the store for assistance.**
COMPETITION SERIES XL POWER
MODEL #7525
Failure to comply with any of the warnings
in these instructions may result in serious
personal injuries such as cuts, broken
bones, nerve damage, paralysis, brain
injury, or death. Failure to comply may
also result in property damage. Please
heed all warnings and cautions. To ensure
your safety, do not attempt to assemble this
system without reading and following all
instructions carefully. Identify and inventory
the parts using the Parts List.
Save this instruction in the event that the manufacturer has to be contacted for replacement parts.
INSTRUCTION #07998 D
WWW.LIFETIME.COM
**U.S. and Canada customers ONLY**
IF ASSISTANCE IS NEEDED,
HOURS: 7:00 a.m. to 5:00 p.m. Monday through Friday (Mountain Standard Time)
**Call or visit our Web site for Saturday hours**
LIFT
BASKETBALL SYSTEM
®
ASSEMBLY INSTRUCTIONS
AND OWNER'S MANUAL
**A MINIMUM OF TWO ADULTS ARE
REQUIRED FOR ASSEMBLY**
®
1 (800) 225-3865
at
8/28/2007
Advertisement
Table of Contents
Related Manuals for Lifetime #7525
Summary of Contents for Lifetime #7525
- Page 1 Parts List. Save this instruction in the event that the manufacturer has to be contacted for replacement parts. INSTRUCTION #07998 D WWW.LIFETIME.COM **U.S. and Canada customers ONLY** IF ASSISTANCE IS NEEDED, **Call or visit our Web site for Saturday hours** BASKETBALL SYSTEM ®...
-
Page 2: Parts List
PARTS LIST Part # Description 00644 Top Pole 006443 Middle Pole ZA08004 Bottom Pole DD00800 502027H Handle 502049G Trigger 830020 Extension Arm (Long) 830204 Extension Arm (Short) 502056 Plastic Guard CA00885 Zip Tie 604084 Height Sticker 80033 Spring Bracket HA00800 Gas Spring 82569 AM05404... - Page 3 PARTS LIST Part # Description Handle Hardware (1017923) 302007 3/8” x 6 /2” Hex Bolt 3000 Release Pin 302008 3/8” Centerlock Nut 30087 /2” x 6 /2” Hex Bolt 30008 /2” Centerlock Nut Main Hardware (HD9185) 300029 /2” x 7 /8” Hex Bolt 300022 /4”...
-
Page 4: Safety Instructions
SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble this system without following the instructions carefully. - Page 5 For a nonpermanent installation of your basketball system, a Ground Sleeve provides an alternative to cementing the pole into the ground. See Page 14 for more information. 1.1 Dig a round hole 24” deep and 18” in diameter. The edge of the hole should be flush with the edge of the playing surface.
- Page 6 Required For This Page: 6.1 Completely tighten the Nuts. 9/6” Wrenches Screwriver HD985 Small holes This step cannot be reversed. 9.1 Strike each end of the Pole firmly 5 to 6 times on a piece of scrap wood or cardboard. BC (2) 005748 The poles must be seated together!! Even if the poles cover the slots...
- Page 7 Required For This Page: HD () 07923 /2” Wrenches 9/6” Wrenches 3/4” Wrenches Scissors/ Wire Cutters/ Pliers Hammer/ Mallet HC (2) HD985 MO (2) ()* ()* *(Not actual size) 11.1 Line up the Rear Lifter Arms (AR) with the Gas Spring (AN). above.
- Page 8 Required For This Page: 17.1 Hold the Backboard Brackets (AP & AQ) together and slide the U-Bolt (RE) through the 9/6” Wrenches holes as shown. Pliers 003678 21.1 Lay the Backboard (AU) on a table or bench. (Not actual size) HD985 Note: The U-Bolt (RE) goes through the upper openings...
- Page 9 Required For This Page: 003678 U-Bolt (RE). /2” Wrench 3/4” Wrenches Electric Drill/ Screwdriver (Not actual size) HD985 24.1 Place the Compression 25.1 Place the Spring Retainer Springs (RG) over the ends of the Plate (RJ) and secure with Nylock Flange Nuts (RF).
- Page 10 Required For This 29.1 Tighten the Nut until it is flush with the Bolt. Page: /2” Wrench 3/4” Wrenches Electric Drill/ Screwdriver HD985 31.1 Rest the Backboard (AU) and Rim (AO) on cardboard to prevent scratching. 30.1 Attach this end of the Long Extension Arms (AE) to the Backboard Brackets (AP &...
- Page 11 Required For This Page: 3/4” Wrenches /2” Socket Wrench Hammer/Mallet Electric Drill HD985 pole. MH (3) HH00700 FA (0) 34.2 Only finger tighten the Nut. 32.1 Remove the plastic film from the Backboard. 33.2 Only finger tighten the Nut. 32.2 Use an electric drill to insert the Screws (FA).
- Page 12 36.1 Attach the Net (AB). Note: Please call our Customer Service Department at the number on Page One to obtain replacement Nets. Our Nets are shorter than average to reduce the risk of entanglement. 38.1 Slowly lift the pole and rotate the Backboard assembly upside down again.
- Page 13 Required For This Page: Screwdriver Hammer/Mallet 39.1 Ensure the Backboard faces the playing surface and align the small hole in the Middle Pole (MP) with the correct Electric Drill slot in the Bottom Pole (BP). Slide the Middle Pole over the Bottom Pole. 005748 39.2 Insert the remaining 1/4”...
- Page 14 Operation of the height adjustment system The adjustable system may be adjusted from 7 1/2 feet to 10 feet. Hold the Handle tightly and squeeze the Trigger to engage the Gas Spring. Raise the Handle to lower the Backboard, or lower the Handle to raise the Backboard.
- Page 16 This warranty is nontransferable and is expressly limited to the repair or replacement of defective basketball equipment. If the equipment is defective within the terms of this warranty, Lifetime Products, Inc. will repair or replace defective parts at no cost to the purchaser. Shipping charges to and from the factory are not covered and are the responsibility of the purchaser.