Do you have a question about the C83332 and is the answer not in the manual?
Questions and answers
Conrad Bernier
May 25, 2025
Can’t get remote to connect. Tried new batteries no luck.
1 comments:
Mr. Anderson
May 26, 2025
To troubleshoot the remote connection issue for La Crosse Technology model C83332:
1. Restart with Fresh Batteries: - Replace old batteries in both the display and remote sensor with new batteries dated at least six years in the future. - Avoid using batteries that have been dropped or show signs of damage.
2. Reset the Weather Station: - Remove batteries from the display. - Press any button 20 times to fully discharge. - Leave the batteries out for at least 2 hours. - Reinsert fresh batteries.
3. Check Sensor Condition: - Ensure the remote sensor has not fallen into water. If it has, it may be water-damaged and needs replacement. - Remote sensors are water-resistant, not waterproof.
4. Battery Performance: - Use reputable battery brands. - Record battery installation date and voltage. If batteries drain quickly, note the failure date and voltage for troubleshooting.
If the issue persists, consider replacing the sensor with the correct model and frequency.
This answer is automatically generated
Donnie Townsley
April 8, 2025
How to shut the alarm off
1 comments:
Mr. Anderson
April 9, 2025
To turn off the alarm on the La Crosse Technology C83332:
1. In normal mode, press and release the ALARM button once to show the alarm time. 2. Press and release the ALARM button repeatedly to turn the alarm OFF. 3. The alarm icon will disappear when the alarm is deactivated.
Model: C83332/C83349 Instruction Manual DC: 121314 WIRELESS COLOR WEATHER STATION Mold Risk for Weather Station & Indoor Remote Sensor Location Color Animated Forecast with Tendency Calendar + Alarm Time Button Press for Mold Risk Button Press Indicator for for Mold Risk...
FCC Statement ......................14 Introduction La Crosse Technology® introduces a Wireless Color Weather Station with precise, real-time backyard weather. New – Monitor the mold risk for two separate areas using the indoor weather station and multi-use remote sensor. Place the remote sensor outdoors to monitor backyard weather conditions, or use it indoors to monitor high mold risk areas like in a crawl space or a basement.
Press to decrease values during setting. Hold 2 seconds to quickly adjust values. Default Time Display- Press to display minimum temperature/humidity. Hold 2 seconds to clear minimum temperature/humidity memory. Temperature Alert- Press to disarm alerts Model: C83332/C83349 www.lacrossetechnology.com/support Page | 4...
Hold to enter Alert setting ALARM Button: Default Time Display- Press once to show alarm time Hold for 2 seconds enter alarm setting mode Alarm Mode- Press to activate or deactivate time alarm. Model: C83332/C83349 www.lacrossetechnology.com/support Page | 5...
1. DST and ON will flash above the date. 2. Press and release the ▼ or ▲ buttons to turn DST to OFF. 3. Confirm with the TIME SET button and move to 12/24 hour time format. Model: C83332/C83349 www.lacrossetechnology.com/support Page | 6...
REMOTE HIGH alert will flash. Press the ▼ or ▲ buttons to set the alert value, and press the ALERT button to confirm. Then press the ALERT button again switch to REMOTE LOW setting. Model: C83332/C83349 www.lacrossetechnology.com/support Page | 7...
2. To stop alarm for one day, press ALARM button, while in snooze mode. The bell icon will remain solid. Note: When the alarm sounds, it continues for 2 minutes and then shuts off completely. Model: C83332/C83349 www.lacrossetechnology.com/support Page | 8...
View Mold Risk Indoor and Remote locations: From a normal display, press the HEAT/DEW button three times and the Mold Risk will show next to the remote and indoor humidity. Model: C83332/C83349 www.lacrossetechnology.com/support Page | 9...
Animated forecast icons use changing atmospheric pressure to predict weather conditions for the next 12-hours with 70-75% accuracy. INTELLIGENT WEATHER FORECAST This station learns; please allow 3 to 4 weeks for barometric calibration. This will ensure an accurate personal forecast for your location. Model: C83332/C83349 www.lacrossetechnology.com/support Page | 10...
Manual WWVB Time Signal Search Press the TIME SET button to start or stop a manual signal search. The WWVB Icon flashes during signal search. WWVB For information about WWVB visit: ATOMIC ICON www.nist.gov/pml/div688/grp40/wwvb.cfm Model: C83332/C83349 www.lacrossetechnology.com/support Page | 11...
The maximum wireless transmission range to the weather station is over 200 feet (60 meters) in open air, not including walls or floors. Be sure the remote sensor is mounted vertically. Model: C83332/C83349 www.lacrossetechnology.com/support Page | 12...
If the product is not working properly, change the batteries and/or check the AC cord connection. Warranty Information La Crosse Technology, Ltd. provides a 1-year limited time warranty (from date of purchase) on this product relating to manufacturing defects in materials & workmanship. View full warranty details online at: www.lacrossetechnology.com/warranty_info.pdf...
This booklet may contain errors or misprints. The information it contains is regularly checked and corrections are included in subsequent editions. We disclaim any responsibility for any technical error or printing error, or their consequences. All trademarks and patents are recognized. Model: C83332/C83349 www.lacrossetechnology.com/support Page | 14...
Need help?
Do you have a question about the C83332 and is the answer not in the manual?
Questions and answers
Can’t get remote to connect. Tried new batteries no luck.
To troubleshoot the remote connection issue for La Crosse Technology model C83332:
1. Restart with Fresh Batteries:
- Replace old batteries in both the display and remote sensor with new batteries dated at least six years in the future.
- Avoid using batteries that have been dropped or show signs of damage.
2. Reset the Weather Station:
- Remove batteries from the display.
- Press any button 20 times to fully discharge.
- Leave the batteries out for at least 2 hours.
- Reinsert fresh batteries.
3. Check Sensor Condition:
- Ensure the remote sensor has not fallen into water. If it has, it may be water-damaged and needs replacement.
- Remote sensors are water-resistant, not waterproof.
4. Battery Performance:
- Use reputable battery brands.
- Record battery installation date and voltage. If batteries drain quickly, note the failure date and voltage for troubleshooting.
If the issue persists, consider replacing the sensor with the correct model and frequency.
This answer is automatically generated
How to shut the alarm off
To turn off the alarm on the La Crosse Technology C83332:
1. In normal mode, press and release the ALARM button once to show the alarm time.
2. Press and release the ALARM button repeatedly to turn the alarm OFF.
3. The alarm icon will disappear when the alarm is deactivated.
This answer is automatically generated