Related Manuals for Hammer Strength OHDPR8
Summary of Contents for Hammer Strength OHDPR8
-
Page 1: Assembly Instructions
’ OLYMPIC HEAVY DUTY POWER RACK 8 (OHDPR8) ASSEMBLY INSTRUCTIONS Part # 7615401 Revision:12/09/03 Rev. C... -
Page 2: Parts List
DESCRIPTION PART # LEFT UPRIGHT BASE LEA7586101 RIGHT UPRIGHT BASE LEA7586501 FRONT UPRIGHT LEA7584601 REAR UPRIGHT LEA7584901 CROSS SUPPORT LEA7585801 WEIGHT HORN UPRIGHT LEA7586601 REAR UPRIGHT SUPPORT LEA7586901 CHIN-UP SUPPORT LEA7588301 RIGHT ADJUSTMENT RACK LEA7584401 LEFT ADJUSTMENT RACK LEA7584501 WEIGHT HORN LEA7587501 LEFT BAR SUPPORT LEA7587901... - Page 3 17 1/2 X 1-1/2” BOLT 26 1/2 X 4-1/4” BOLT 16 1/2 X 4-1/2” BOLT 18 3/8 X 3-3/4” FLAT HEAD BOLT 1/2” INT TOOTH LOCK WASHER 1/2” PLASTIC DOME WASHER 3/8” INT TOOTH 1/2” LOCK WASHER FLAT WASHER 3/8” 1/2”...
- Page 4 FIGURE 1 STEP 1: • LOOSELY assemble the REAR UPRIGHT (4) to the LEFT UPRIGHT BASE (1) using two 1/2 X 4-1/4” BOLTS (26), two 1/2” PLASITC DOME WASHERS (22), two 1/2” INT TOOTH LOCK WASHERS (20) and two 1/2” LOCK NUTS (23) as shown in FIGURE 1. •...
- Page 5 Use this set of holes for assembly with PLATFORM. FIGURE 2 STEP 2: • LOOSELY assemble the BOTTOM UPRIGHT SUPPORT (15) to the REAR UPRIGHTS (4) using four 1/2 X 4-1/4” BOLTS (26), four 1/2” PLASITC DOME WASHERS (22), four 1/2” INT TOOTH LOCK WASHERS (20) and four1/2” LOCK NUTS (23) as shown in FIGURE 2.
- Page 6 FIGURE 3 STEP 3: • LOOSELY assemble the FRONT UPRIGHT (3) to the LEFT UPRIGHT BASE (1) using two 1/2 X 4-1/4” BOLTS (26), two 1/2” PLASITC DOME WASHERS (22), two 1/2” INT TOOTH LOCK WASHERS (20) and two 1/2” LOCK NUTS (23) as shown in FIGURE 3. •...
- Page 7 FIGURE 4 1/2 X 4-1/2” 16 STEP 4: • LOOSELY assemble the REAR UPPER SUPPORT (7) and the CROSS SUPPORTS (5) to the REAR UPRIGHTS (4) using four 1/2 X 4- 1/2” BOLTS (16), eight 1/2” INT TOOTH LOCK WASHERS (20) and four 1/2” LOCK NUTS (23) as shown in FIGURE 4. •...
- Page 8 FIGURE 5 1/2 X 4-1/4” 26 1/2 X 4-1/2” 16 STEP 5: • LOOSELY assemble the CHIN-UP SUPPORT (8) to the CROSS SUPPORTS (5) and the FRONT UPRIGHTS (3) using two 1/2 X 4-1/2” BOLTS (16), two 1/2 X 4-1/4” BOLTS (26), six 1/2” INT TOOTH LOCK WASHERS (20), two 1/2” PLASTIC DOME WASHERS (22) and four 1/2”...
- Page 9 FIGURE 6 1/2 X 4-1/4” 26 26 1/2 X 4-1/4” STEP 6: • LOOSELY assemble the WEIGHT HORN UPRIGHTS (6) to the LEFT & RIGHT UPRIGHT BASE (1 & 2) using four 1/2 X 4-1/4” BOLTS (26), four 1/2” PLASTIC DOME WASHERS (22), four 1/2” INT TOOTH LOCK WASHERS (20) and four 1/2” LOCK NUTS (23) as shown in FIGURE 6.
- Page 10 FIGURE 7 TIGHTEN! TIGHTEN! TIGHTEN! TIGHTEN! STEP 7: • Securely tighten all loose frame connections made to this point.
- Page 11 FIGURE 8 STEP 8: • LOOSELY assemble one RIGHT & one LEFT ADJUSTMENT RACK (9 & 10) to the REAR UPRIGHTS (4) as shown, using eight 3/8 X 3-3/4” FLAT HEAD BOLTS (18), eight 3/8” INT TOOTH LOCK WASHERS (21) and eight 3/8” LOCK NUTS (24). See FIG- URE 8.
- Page 12 FIGURE 9 1/2 X 4-1/4” 26 STEP 9: • SECURELY assemble the ten WEIGHT HORNS (11) to the WEIGHT HORN UPRIGHTS (6) using twenty 1/2 X 4-1/4” BOLTS (26), twenty 1/2” INT TOOTH LOCK WASHERS (20), twenty 1/2” PLASTIC DOME WASHERS (22) and twenty 1/2” LOCK NUTS (23) as shown in FIGURE 9.
- Page 13 FIGURE 10 17 1/2 X 1-1/2” STEP 10: • Assemble two SWIVEL SPOTTERS (25) to the BOTTOM UPRIGHT SUPPORT (15) as shown using four 1/2 X 1-1/2” BOLTS (17), four 1/2” FLAT WASHERS (19), four 1/2” INT TOOTH LOCK WASHERS (20) and four 1/2” LOCK NUTS (23). See FIGURE 10. (NOTE: Tighten connection SECURELY then back nut off 1/2 turn.)
- Page 14 FIGURE 11 STEP 11: • Insert the LEFT BAR SUPPORT (12) into the desired slots of the LEFT ADJUSTMENT RACK (10), and allow it to drop down to lock in place. See FIGURE 11. • Repeat the above step to assemble the RIGHT BAR SUPPORT (13) to the RIGHT ADJUSTMENT RACK (9). •...
- Page 15 FIGURE 12 SERIAL NUMBER SERIAL NUMBER SERIAL NUMBER STEP 12: • Insert the BAR CATCHES (14) into the desired slots on the LEFT & RIGHT ADJUSTMENT RACKS (10 & 9), and allow it to drop down and lock into place. See FIGURE 12. Thank you for purchasing the OLYMPIC HEAVY DUTY POWER RACK.
-
Page 16: Warranty Information
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please follow these rules: 1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately. Failure to do so may result in serious injury. 2.