Related Manuals for Loctite 175
Summary of Contents for Loctite 175
- Page 1 EQUIPMENT Operation Manual 175 Dispenser P/N: 98035 RoHS 120V, 50/60Hz 400W Compliant Label # 985029 Label P/N 8900605 ® Loctite 175 Hot Melt Dispenser 120 Volt Part Number 98035 230 Volt Part Number 98055...
-
Page 2: Table Of Contents
Table of Contents PLEASE OBSERVE THE FOLLOWING ..............3 1.1 E ......................3 MPHASIZED ECTIONS 1.2 S ..........................3 AFETY 1.3 I .........................3 TEMS SUPPLIED DESCRIPTION .........................4 TECHNICAL DATA ......................4 INSTALLATION ......................5 OPERATION........................6 5.1 T ..................6 TANDBY EATURE 5.2 T .....................6 EMPERATURE ADJUSTMENT APPLICATION HINTS ....................7 TROUBLESHOOTING ....................7 7.1 S... -
Page 3: Please Observe The Following
Do not touch the nozzle or molten adhesive with bare skin as they are hot - the ® operating temperature of the Loctite 175 Hot Melt Dispenser is approximately 400ºF (200ºC). Protective gloves should always be worn. Careless handling can cause skin burns. If molten adhesive comes into contact with the skin immerse the affected area immediately in plenty of cold water. -
Page 4: Description
Description ® The Loctite 175 Hot Melt Dispenser contains a powerful 400W stainless steel cartridge heater which, in conjunction with it’ s adjustable solid-state electronic controller, provides both a fast 5-minute warm-up, and accuracy in temperature control to within +/- 10°F (5°C) of the set temperature. Temperature adjustment is achieved by changing the plug-in module –... -
Page 5: Installation
Installation Before using the tool for the first time check it carefully for signs of external damage. If any shipping damage is found DO NOT USE THE TOOL - return it to your supplier immediately. Steps 1 –5 should be followed before connection to the main power supply: Assemble the enclosed stand into the grooves at the base of the handle. -
Page 6: Operation
Operate the tool normally. The Auto Standby Feature ® With a tool as powerful as the Loctite 175 Hot Melt Dispenser there would be a risk of adhesive ‘ meltdown’if it were left unused for too long at its normal operating temperature. -
Page 7: Application Hints
Foam materials, like polystyrene, can be easily bonded to other surfaces. However the adhesive must be applied to the other surfaces, not to the foam. ® Use only genuine Loctite Hot Melt adhesives to ensure reliable performance. ® Loctite Hot Melt adhesives are non-toxic and non-flammable. -
Page 8: Feed Mechanism Adjustment
If feed mechanism adjustment is set too tight, plunger withdrawal will be very difficult. FOR ANY REPAIRS OR ADJUSTMENTS –OTHER THAN THOSE DETAILED IN THIS MANUAL –PLEASE CONTACT 1-800-LOCTITE (562-8483). Care and Maintenance When in use, do not lay the tool on its side - always place upright using the stand provided. -
Page 9: Accessories And Spare Parts
Accessories and Spare Parts Spare Parts Part # Spare Parts Part # Complete Nozzle Check Adapter Assembly 985078 U.S. Cordset Kit 985226 Qty 1 –Cordset, Item 17 Nozzle Check Adapter Only (included with 985088 Qty 1 –Cord Clamp, Item 16 985078) Qty 2 –Screws, Item 42 Temperature Control 110/120V... -
Page 10: Appendix
Accessories and Spare Parts (continued) Accessories Part Number Standard Nozzle 1-Hole Kit, Qty 5, 0.080”(2mm) orifice 985225 Nozzle 2-Hole 985110 Nozzle 3-Hole 985111 Extension Nozzle 0.120”(3mm) 985112 Needle Extension Nozzle 0.050”(1.3mm) 985113 Spreader Extension Nozzle 0.250”(6mm) 985114 “ L”Nozzle, overlap carton sealing 985115 “... -
Page 11: Exploded Diagram
Exploded Diagram... -
Page 12: Parts List
Parts List Item Description Rebuild Kits Available Part No. Main Capacitor Assembly, 120V 985178 Main Capacitor Assembly, 230V 985757 Torsion Spring Trigger Kit 985540 Helical Spring Lock Washer Heater Housing Kit 985221 Snubber Screw Feed Bar Kit 985220 Earth (Ground) Screw Heater Housing Kit 985221 Feed Bar Plunger Screw... -
Page 13: Warranty
® Loctite 175 Hot Melt Dispenser (hereafter called "Products") shall be free from defects in materials and workmanship. Liability for Henkel shall be limited, as its option, to replacing those Products which are shown to be defective either in materials or workmanship or to credit to the purchaser the amount of the purchase price thereof (plus freight and insurance charges paid therefor by the user). - Page 14 Canhema 09941-410 32100 Stephenson Hwy. Diadema/SP, Brazil www.loctite.com Madison Heights, MI 48071 ® and ™ designate trademarks of Henkel Corporation or its affiliates. ® = registered in the U.S. and elsewhere. © Henkel Corporation, 2009. All rights reserved. Data in this operation manual is subject to change without notice.