Parabody home gym assembly instructions (18 pages)
Summary of Contents for ParaBody 360101
Page 1
Serious Steel 1360101 375 LEG PRESS ADAPTER KITi ASSEMBLY INSTRUCTION Eevision: 07/06/99 Part # 6837701...
Page 2
Parabody customer service Please note: * Thank you for purchasing the Parabody 360101 Leg Press Adapter Kit. Please read these instructions thoroughly and keep them for future reference. This product faust be assembled on a flat, level surface to assure its proper function.
PART# DESCRIPTION 6838003 FRON~FLEG Pig I .FY BRACKET 6693902 6838103 ’ BASE CONNECTION 3116i01 3-V2"eULLZY " ~ 6405201 2" SQ. END CAP 6-~700~ 2" SQ. COVER 68~2701 ’ 2" SQ. r~UBB~BUM~ZR 3102501 3/8" %VASHER NOTE: The LEG PRESS ATTACHMENT STEP 1 ¯...
Page 4
STACK GUARD FIGURE 4 STEP 4 ¯ Remove two 1/2 X 4" BOLTS, two 1/2" WASHERS, and two 1/2" LOCK NUTS from the BASE and STACK GUARD as shown in FIGURE 4. (NOTE: Discard the 1/2 X 4" BOLT.) FIGURE 5 STEP 5 ¯...
Page 5
REMOVE STEP 6 Remove the existing CABLE (part #68331) using the following steps: ¯ Disconnect LAT BAR from TOP BOOM. ¯ Unscrew the threaded end of CABLE from the HEAD PLATE ASSEMBLY. ¯ Route the CABLE around the FLOAT~’G PULLEY as shown in FIGURE 6. ¯...
Page 6
FIGURE 7 IMPORTANT: Cable must run in all the pulley grooves. ;TEP 7 Install the NEW PRIMARY CABLE (13) using the following steps: ¯ Route the CABLE (13) through the TOP BOOM as sho~a in FIGURE 7. The pulleys in TOP BOOM may need to be temporarily removed to perform this step.
Page 7
FIGURE 8 STEP 8 Loop CABLE (13) around one 3-1/2" PULLEY (4) in the PULLEY BRACKET BOLT (10), and two 3/8" WASHERS (8) and one 3/8" LOCK NLrI" (9) as shown in FIGURE STEP 9 ¯ Remove one existing 3-1/2" PULLEY, two WASHERS, two 2"...
Page 8
STEP 10 ¯ Assemble the LEG PRESS CABLE (14) to the ADJUSTMENT BOLTS, SPACERS, WASHERS, 2" WHEELS AND NUT. (Note: Do not overtighten! Tighten only until nut is completely on bolL) FIGURE 10. 3/8 X 4-1/2" BOLT TUBE on the 832 using the existing previoasly removed 3/8 X 4-1/2"’ SPACER DONOT FIGURE 10...
Page 9
FIGURE 11 STEP 11 ¯ Secure~yfastenthe832LEGPRESSt~theFRONTLEG(~)usingtw~/2X3~BOLTS(~)~tw~/2~WASHE~‘S(~5)~andtw~/2~L~CK NUTS (16) as shown in FIGURE 11.
Page 10
STEP 12 ¯ Attach one 3-1/2" PULLEY (4) to the FRONT LEG (1) and one 3-1/2" PULLEY (4) to the BASE CONNEC([’ION 2" BOLTS (10), four 3/8" WASHERS (8) and two 3/8" LOCKNI_rTS (9). (Note: Make sure CABLE (14) is running pUI ~! ,~YS.) STEP 13 ¯...
Page 11
¯ If further adjustment is needed, lossen and adjust the pulley attached to the slotted tab on the BENCH FRAME. (NOTE: It is natural for the LEG PRESS CABLE to slacken when seat is adjusted inward.) Thank you for purchasing the Parabody 360101 Leg Press Adapter Kit. call your local...