Regency Ceiling Fans Mirada Tandem Owner's Manual
  1. Manuals
  2. Brands
  3. Regency Ceiling Fans Manuals
  4. Fan
  5. Mirada Tandem
  6. Owner's manual

Regency Ceiling Fans Mirada Tandem Owner's Manual

Ceiling fan
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Style that revolves around you.
C
F
O
'
M
•
•
eiling
an
wner
s
anual
• M
T
F
•
irada
andeM
an
1/08
WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout.
01/08

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Mirada Tandem and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Regency Ceiling Fans Mirada Tandem

Summary of Contents for Regency Ceiling Fans Mirada Tandem

  • Page 1 Style that revolves around you. ’ • • eiling wner anual • M • irada andeM 1/08 WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout. 01/08...

  • Page 2: Important Safeguards

    & O eneral nsTallaTiOn peraTiOn nsTruCTiOns mportant afeguardS 1. To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly before beginning. 2. To avoid possible electrical shock, be sure electricity is turned off at the main power box before wiring. All electri- cal connections must be made in accordance with local codes, ordinances and/or the National Electric Code.

  • Page 3: Tools And Materials Required

    MpOrTanT aFeTy reCauTiOns Thank you for choosing a Regency Ceiling Fan. You have chosen the best! Your new ceiling fan has been designed to provide many years of service and enjoyment. Warnings: • Disconnect power by removing fuse or turning off circuit breaker before installing the fan and/or optional lighting.
  • Page 5 reparaTiOn Parts identification on Downrod with Cover assembled fan Housing Extension Collar Cover Blade Blade reparatIon Verify that you have all parts before beginning the installation. Check foam insert closely for missing parts. Remove motor from packing. To avoid damage to finish, assemble motor on soft padded surface or use the original foam inset in motor box. Do not lay fan on its side as this could result in shifting of motor in decorative enclosure.
  • Page 6 nsTalling ttach ownrod 1. Carefully support fan body (motor) in its styrofoam packing with the mounting collar (where the wires come out) facing upward. 2. Remove ball from the downrod by loosening set screw in the side of the ball. Slide ball down and remove ball pin;...
  • Page 7 nsTalling an COnTinued SSembly 8. Install the decorative arm into extension arm, the post on the decorative arm will seat into the hole on the extension arm as shown in detail below. Screw the decorative arm to the downrod cover using the screw that was removed in step 7 (Fig.
  • Page 8 nsTalling The an COnTinued WARNING: To avoid damaging the blade arms and blades, do not install them onto fan until fan is fastened to ceiling. 1. Lift ball/downrod/fan into hanging bracket opening. NOTE: The tab opposite hanging bracket opening should fit in slot on ball (Fig.
  • Page 9 leCTriCal OnneCTiOns Be sure electricity is turned off at the main power box before wiring lectrIcal onnectIonS 1. Four wires are connected to the fan (Fig. 1). Black – this is the “hot” power to run fan. Blue - this is the “hot” power to operate the down light (light kit) White –...
  • Page 10 lade TTaChMenT lade ttachment 1. Place fiber washer on screw. Insert this assembly through the blade and start the screw into the blade arm. Repeat this procedure without tightening the screw until all 3 screws have been started into the blade arm (Fig. 1). NOTE: Fans that have painted finishes may be packed with gaskets that can be used between the blade arm and blade to help prevent a clicking noise that may develop if blade screws loosen over time.
  • Page 11 ighT ighT nsTallaTiOn pTiOnal 1. Remove one screw from the optional light kit base (Fig. 1). 2. Lift light kit attachment up to fan motor. Insert the screws from the motor into the key hole on the light kit base and rotate until it locks in place. Then tighten the two loose screws and reinsert the third screw and tighten all the way.
  • Page 12 iThOuT ighT ighT nsTallaTiOn pTiOnal 1. Install the cap mounting post using the three screws located on the mounting collar (Fig. 1) 2. Slide the cap over the mounting post and screw in place using the finial (Fig. 2) Mounting Collar Screw Mounting Post Mounting Post...

  • Page 13: General Information

    eMOTe OnTrOl eneral nformatIon NOTE: For use with a standard remote control. Multiple code choices are included with your fan’s remote control in case: • you have more than one remote control fan and want them to respond only to their own remote control •...

  • Page 14: Troubleshooting

    rOuBleshOOTing ase OF iFFiCulTy 1. If fan will not start: Check main and branch circuit breakers and/or fuses. Check line wire connections to fan and switch housing wiring. Make sure forward/reverse switch is set to one or the other position, not stuck in between. 2.

  • Page 15: Care And Cleaning

    NOTE: When dusting the blades, you must support the blade to prevent bending - no pressure should be applied to the blades. hank yOu FOr purChasing a egenCy eiling Write to us at: Regency Ceiling Fans P.O. Box 730 Fenton, MO 63026 For additional troubleshooting tips, visit us on the Web at: www.regencyfan.com 1/08 Regency Ceiling Fans...

Table of Contents