Pairing Cameras With Remotes Preparation for Use Get Set! Ready! Set! Go! Connection USB Mode – Capturing and Adjusting Images Using a Computer Specifications SD Mode – Capturing Images Without a Computer or Without Specifications a Wireless Device Leica ICC50 W User Manual...
Page 3
General Notes Leica ICC50 W User Manual General Notes...
General Notes The Leica ICC50 W camera includes an inter- Before installing, operating or using the instru- active CD-ROM with all relevant user manuals. ments, read the user manuals listed above. In Keep it in a safe place, and readily accessible particular, please observe all safety instructions.
Safety Instructions Safety concept Description Location of use Before using your Leica ICC50 W camera for The Leica ICC50 W fulfills the highest require- See "Safety concept" booklet the first time, please read the "Safety concept" ments for observation and documentation.
Page 6
Safety Instructions (Continued) Transport EC Declaration of Conformity Use the original packaging for shipping or See "Safety concept" booklet transporting the Leica ICC50 W camera. Health risks In order to prevent damage from vibrations, disassemble all moving parts that (according to...
Page 7
3.2 of the R&TTE directive. Intended for indoor use only in all EU member states, EFTA states and Switzerland. Radio interference suppression in compli- ance with EN 55011 class ?? Leica ICC50 W User Manual General Notes...
20 cm between the radiator and your body. Reorient or relocate the receiving antenna. This transmitter must not be co-located or oper- Increase the separation between the equip- ating in conjunction with any other antenna or ment and receiver. transmitter. Leica ICC50 W User Manual General Notes...
Functional disturbances or damaged instruments Warning of hazardous electrical voltage This symbol indicates especially impor- tant information that, if not observed, can cause the following: Hazards to personnel Functional disturbances or damaged instruments Leica ICC50 W User Manual General Notes...
Risk of electric shock. Removing the results. covers of the Leica ICC50 W camera Repairs may only be carried out by Leica Micro- exposes hazardous voltages, which if contacted, systems-trained service technicians. Put the available dust cover over the micro- could cause injury or death.
Introduction Thank you for purchasing the Leica ICC50 W by Leica Microsystems. The special design of the Leica ICC50 W makes it a universal, highly versa- tile tool for viewing microscopic specimens and capturing still images or video. Leica ICC50 W User Manual...
SD card application. use remote control 2. WiFi mode Power Leica ICC50 W – 5 V/1.5 A Wireless connection to wireless device (tablet, Power can be provided to the camera in the phone, PC) following ways: USB power connector on the microscope 3.
1. LED status indicator Blinking red means starting up Green means ready 2. Capture button for SD card capture 3. Mode selection panel 4. SD card slot 5. Power on/off button 6. Service button Leica ICC50 W User Manual The Leica ICC50 W...
Page 17
Leica ICC50 W: Overview (Continued) 1. Ethernet socket for connecting an ethernet cable (cable not provided) 2. HDMI for connecting the provided HDMI cable 3. USB for connecting the provided USB cable Front Infrared window: Receives the signal from the optional remote control.
If you ordered the Optional USB power supply you If you ordered the handheld remote, you received imaging software, HDMI cable, and USB cable. have also received a power supply. the remote with batteries. Leica ICC50 W User Manual The Leica ICC50 W...
Allen key (provided with microscope) 1. If the microscope’s viewing tube is in place, Leica ICC50 W) into the stand support. remove it. Attach the Leica ICC50 W to the microscope stand: 2. Slightly unscrew the set screw (located on ...
Page 21
Preparation for Use (Continued) 5. Attach the microscope viewing tube onto the Leica ICC50 W using the set screw, which is located on the left side of the Leica ICC50 W camera module. Leica ICC50 W User Manual Get Ready!
Connection Connect the camera to a power source 2. Via provided USB cable to external USB Note the Leica ICC50 W requires 5 V/1.5 A power supply. for power, therefore, a proper power supply must be used. Connect to a power source by one of the follow- ing methods: 1.
USB port, and attach the other the status light is green and one of the Leica ICC50 W’s field of view, however, is rectan- end of the cable to a USB 2.0 port of your mode button's is also green. This may take gular with a diagonal of 16.4 mm to ensure an...
Page 25
4:3 using the controls of the projector or monitor. 6. You are ready to launch the Leica software. Follow the software instructions to adjust and capture an image.
2. Press the red power button. 3. The status light will blink red. Wait until the status light is green and one of the mode button's is also green. This may take approximately 30 seconds. Leica ICC50 W User Manual Get Set!
5. Insert the SD memory card into the slot on Capturing an image You will hear a beep to acknowledge the • the side of the Leica ICC50 W until the card It is critical to properly set the micro- button was pressed. clicks into place.
The new white balance setting will generate a neutral Press and hold the capture button for 5 seconds. background for both illuminations. Wait for the beep. A new white balance is set. Leica ICC50 W User Manual Get Set!
This may take approximately 30 seconds. 6. Open the appropriate app on your mobile device or appropriate software on your wireless enabled PC for viewing, capturing, and adjusting the camera image. Leica ICC50 W User Manual Get Set!
– see power source section on is lit green, then press the ethernet button page 23. and wait until both the status LED and the ethernet LED mode button is green. 3. Press the red power button. Leica ICC50 W User Manual Get Set!
SD mode and when the camera is used in combination with an HD display. The only function which works in any mode is the "Info" function which shows details about the camera. Leica ICC50 W User Manual The Camera Remote Control...
7. Brightness adjustment up or down 8. Pairing button 9. Show/hide information box 10. White balance set button 11. Call up the camera menu 12. Arrow keys for navigation 13. OK to confirm Leica ICC50 W User Manual The Camera Remote Control...
Viewing Images and Movies With the Optional Remote Control If you have purchased the optional remote, the Leica HD camera shows images and movie clips directly on an HD moni- tor. 1. Thumbnail view (first press) up/down/left/right select thumbnail...
3. Press the and buttons to select a menu item. 4. Press the button to confirm a menu item. 5. Press the button again to hide the camera menus. Leica ICC50 W User Manual The Camera Remote Control...
The values for "RED" and "BLUE" cannot be adjusted if the "WB MODE" setting is set to "AUTO". The "COLOR" function makes it possible to adapt the camera chip to the ambient light so that color-neutral images can be acquired. Leica ICC50 W User Manual The Camera Remote Control...
The "COLOR" function makes it possible to adapt the camera chip 6. Press the button to exit the menu. to the ambient light so that color-neutral images can be acquired. Leica ICC50 W User Manual The Camera Remote Control...
3. Set the value for "EXP MODE" to "MANUAL". RESOLUTION GAIN SETUP CAMERA BRIGHTNESS 4. Correct the values for "EXPOSURE", "GAIN" and "GAMMA" until you SETUP ETHERNET GAMMA obtain the desired results for the image. SETUP WIFI Leica ICC50 W User Manual The Camera Remote Control...
Indicates the resolution of the captured videos on the SD card. SETUP WIFI The "RESOLUTION" menu enables you to define the resolution for the live image, still image capture and video capture individually. This provides optimum results in every situation. Leica ICC50 W User Manual The Camera Remote Control...
This command sets the date and time as well as the format for display- capture. ing them. The following formats are available for selection: YYMMDD – DDMMYY – MMDDYY Leica ICC50 W User Manual The Camera Remote Control...
Main menu Sub menu Ethernet COLOR IP ADDRESS STATIC EXPOSURE IP ADDRESS (STATIC) 192.168.1.200 RESOLUTION IP SUBNET MASK 255.255.255.0 SETUP CAMERA GATEWAY IP ADDRESS 192.168.1.1 SETUP ETHERNET SETUP WIFI Leica ICC50 W User Manual The Camera Remote Control...
Page 41
Your network provides the access point and the camera connects to your network by WiFi. NAME (SSID) This is the camera name which will appear. You can change the name using the onscreen keyboard. Leica ICC50 W User Manual The Camera Remote Control...
Page 42
If "OK" is selected, you will see a list of WiFi access points nearby. COLOR INTERFACE NET WORK EXPOSURE NAME (SSID) ICC50 W_2345 RESOLUTION SECURITY OPTIONS NONE SETUP CAMERA PASSWORD (8 CHR) SETUP ETHERNET SCAN SSID SETUP WIFI Leica ICC50 W User Manual The Camera Remote Control...
Pairing Cameras With Remotes Pairing 3. The microscope only responds to the The Leica ICC50 W and the remote control remote control commands from this can be paired and then only respond remote control. to each other. This can be helpful when using Resetting to factory setting multiple cameras and remote controls.
Ready! Set! Go! Now all you need to do is properly set up your microscope, capture your images, and enjoy! Leica ICC50 W User Manual...
Page 46
Specifications Due to the technology of the camera, the speci- fications are changing regularly. Please visit website www.leica-microsystems.com/ education for the latest brochure downloads to find the up to date specifications. Leica ICC50 W User Manual Specifications...
HDMI connector (Typ A) Network adapter one RJ-45 connector Memory card reader supports up to 32 GB Power supply via USB cable to external power supply, microscope stand or PC Power requirment max. 10 W Leica ICC50 W User Manual Specifications...
Page 48
The Leica Microsystems Industry Division’s focus is to support customers’ pursuit Denmark ∙ Ballerup 4454 0101 4454 0111 of the highest quality end result. Leica Microsystems provide the best and most France ∙ Nanterre Cedex 811 000 664 1 56 05 23 23 innovative imaging systems to see, measure, and analyze the microstructures in Germany ∙...