Applicable Controls - Toshiba RAV-SM564UTP-E Installation Manual

8

Applicable controls

REQUIREMENT
• When you use this air conditioner for the first time, it
takes approx. 5 minutes until the remote controller
becomes available after power-on. This is normal.
<When power is turned on for the first time after
installation>
It takes approx. 5 minutes until the remote controller
becomes available.
Approx. 5 minutes
"SETTING"
"SETTING"
Power on
goes out
flashes
<When power is turned on for the second (or later)
time>
It takes approx. 1 minute until the remote controller
becomes available.
Approx. 1 minutes
"SETTING"
"SETTING"
Power on
goes out
flashes
• Normal settings were made when the indoor unit was
shipped from factory.
Change the indoor unit settings as required.
• Use the wired remote controller to change the
settings.
* The settings cannot be changed using the
wireless remote controller, sub remote controller,
or remote-controller-less system (for central
remote controller only). Therefore, install the
wired remote controller to change the settings.
27-EN
 Basic procedure for changing
settings
Change the settings while the air conditioner is not
working. (Stop the air conditioner before making
settings.)
CAUTION
Set only the CODE No. shown in the following table: Do
NOT set any other CODE No.
Remote
controller is
If a CODE No. not listed is set, it may not be possible to
available
operate the air conditioner or other trouble with the
product may result.
* The displays appearing during the setting process
differ from the ones for previous remote controllers
(AMT31E). (There are more CODE No.)
Remote
controller is
available
4
6
1 5 2
1
Push and hold button and "TEMP."
button simultaneously for at least 4
seconds. After a while, the display flashes
as shown in the figure. Confirm that the
CODE No. is [01].
• If the CODE No. is not [01], push
clear the display content, and repeat the
procedure from the beginning. (No operation of
the remote controller is accepted for a while
after button is pushed.)
(While air conditioners are operated under the
group control, "ALL" is displayed first. When
is pushed, the indoor unit number
displayed following "ALL" is the header unit.)
(* Display content varies with the indoor unit
model.)
2
Each time
unit numbers in the control group change
cyclically. Select the indoor unit to change
settings for.
The fan of the selected unit runs and the louvers
start swinging. The indoor unit for change settings
can be confirmed.
3
Specify CODE No. [
buttons.
4
Select SET DATA [
buttons.
5
Push button. When the display changes
from flashing to lit, the setup is completed.
• To change settings of another indoor unit,
repeat from Procedure
• To change other settings of the selected indoor
1
unit, repeat from Procedure
3
Use CL button to clear the settings. To make
settings after
CL
2
Procedure .
6
When settings have been completed, push
button to determine the settings.
When button is pushed,
then the display content disappears and the air
conditioner enters the normal stop mode.
(While is flashing, no operation of the
remote controller is accepted.)
button to
– 14 –
 Installing indoor unit on high
button is pushed, indoor
ceiling
When an indoor unit is installed on a ceiling higher than
the standard height, make the high-ceiling setting for
fan speed adjustment.
Follow to the basic operation procedure
1 2 3
( → →
• For the CODE No. in Procedure
• Select the SET DATA for Procedure
"Height list of ceiling possible to be installed" table in
this manual.
] with "TEMP." /
◆ Remote controller-less setting
] with "TIME" /
Change the high-ceiling setting with the DIP switch on
the receiver section P.C. board.
For details, refer to the manual of the wireless remote
controller kit. The settings can also be changed with
the switch on the indoor microcomputer P.C. board.
2 * Once the setting is changed, setting to 0001 or 0003
.
is possible, however setting to 0000 requires a
setting data change to 0000 using the wired remote
3
.
controller (separately sold) with the normal switch
setting (factory default).
button was pushed, repeat from
flashes and
SET DATA
0000
(Factory default)
0001
0003
To restore the factory defaults
To return the DIP switch settings to the factory defaults,
set SW501-1 and SW501-2 to OFF, connect a
separately sold wired remote controller, and then set
the data of CODE No. [5d] to "0000".
4 5 6
→ → → ).
3
, specify [5d].
4
from the
SW501-1
SW501-2
MCU(IC501)
SW501-1 SW501-2
OFF OFF
ON OFF
OFF ON
28-EN