CAUTION :The laser used in the Super Multi DVD Drive can damage your eyes. Do not attempt to open the cover. To reduce the risk of electric shock, do not remove the cover (or back). There are no user-serviceable parts inside. Refer servicing to qualified service personnel.
This product is manufactured to comply with the radio interference requirements of EEC DIRECTIVE 89/336/EEC, 93/68/EEC and 73/23/EEC. CAUTION - INVISIBLE LASER RADIATION WHEN OPEN, AVOID EXPOSURE TO BEAM. VARNING - OSYNLIG LASERSTRÄLNING NÄR DENNA DEL ÄR ÖPPNAD STRÄLEN ÄR FARLIG.
+5V/+12V power socket required Software Required OS Windows 98/2000 Professional/ME/XP(Home Edition/ Professional), Direct X 9.0 or Higher is required CD-R : LG, Mitsubishi Chemical, Verbatim, Taiyo Yuden, TDK or SKC CD-R, CD-RW, DVD-R, discs are recommended. DVD-RW, DVD+R, CD-RW : LG, Ricoh, Mitsubishi Chemical, Verbatim discs are recommended.
❏ Occasionally CD-R and CD-RW discs written by a CD-R/RW drive cannot be read by other CD drives*. These unreadable discs may need to be read using the CD-R/RW drive they were created with The disc written using the CD-R/RW drive might not be readable by CD-ROMs other than Multi-read compatible (UDF compatible) CD-ROMs Multiread compatible (UDF compatible) CD-ROMs are: 1.
Installing the Drive Before installing the drive, please note the following points. I You will need the following: • A screw driver of a suitable size to fit the securing screws for the drive unit. • The manual for the computer, so you can find the mounting positions for the IDE controller cable.
NOTE : Only one jumper should be installed on the jumper connector. If more than one jumper is installed, the drive may malfunction or be damaged. Master/Slave setting is determined by jumper installation on the Jumper Connector. The following table shows the possible jumper settings. Name Function Drive set as Master...
To Install as a Slave Drive To install the drive as a Slave, change the jumper setting on the rear panel to SL. Master drive (Booting hard disk) Slave drive (Super Multi DVD Drive) (Jumper set to Slave) Connecting the Power Connector Connect the power cable from the computer’s power supply to the socket on the drive unit, fitting the connector firmly into the power in connector.
Connecting the Sound Card If the computer is using a sound card, the drive is connected to the sound card with an audio cable. The supplied analog audio cable fits most sound cards or one can be purchased at a local computer store.
How to Use the Discs When using CD-ROM discs, CD-R discs, DVD discs or CD-RW discs, don’t attach any stickers or labels to the discs. It could cause read and write errors, but data on the disc may be lost due to damage to the disc itself.
Troubleshooting Before Requesting Service Before calling for service, check this list. The drive doesn’t have power. • • Is the power supply cable from the host computer plugged in? • Is the Power Connector to the drive securely attached? The system doesn’t start. •...
Specifications Items General Supported Discs Disc Diameter Host Interface Read/Write Speed Mounting direction Performance Data transfer rate *Sustained *Burst(ATAPI) Average Access Time (Random) Buffer capacity MTBF Audio Output Line Output Environmental When operating Level When not operating Dimensions Dimensions (WxHxD) &...
550 MATHESON Blvd. East Mississauga. Ontario L4Z4G3 Canada LG Electronics Deutschland GMBH Jakob-Kaiser-Straße 12, D-47877 Willich, Germany LG Electronics U. K. Ltd. LG House, 264 Bath Road, Slough Berkshire SL1 4DT United Kingdom Goldstar France E.U.R.L Paris Nord II 22, Avenue des Nations-B.P.50372 VILLEPINTE...