Range Installation - Electrolux 30" DUAL FUEL Installation Instructions Manual

30" DUAL FUEL SLIDE-IN RANGE INSTALLATION INSTRUCTIONS
Isolate the range from the gas supply piping system
by closing its individual manual shutoff valve during any
pressure testing of the gas supply piping system at test
pressures equal to or less than 1/2 psig (3.5 kPa or 14"
water column).
LP/Propane Gas Conversion
This appliance can be used with Natural gas or LP/
Propane gas. It is shipped from the factory for use with
natural gas.
If you wish to convert your range for use with LP/Propane
gas, use the supplied fixed orifices located in a bag
containing the literature marked "FOR LP/PROPANE GAS
CONVERSION." Follow the instructions packaged with
the orifices.
The conversion must be performed by a qualified service
technician in accordance with the manufacturer's
instructions and all local codes and requirements. Failure
to follow these instructions could result in serious injury
or property damage. The qualified agency performing
this work assumes responsibility for the conversion.
Failure to make the appropriate
conversion can result in personal injury and property
damage.
Moving the Appliance for
Servicing and Cleaning
Turn off the range line fuse or circuit breakers at the
main power source, and turn off the manual gas shut-off
valve. Make sure the range is cold. Remove the service
drawer (warmer drawer on some models) and open the
oven door. Lift the range at the front and slide it out of
the cut-out opening without creating undue strain on the
flexible gas conduit. Make sure not to pinch the flexible
gas conduit at the back of the range when replacing the
unit into the cut-out opening. Replace the drawer, close
the door and switch on the electrical power and gas to
the range.
If the range regulator is connected to rigid piping, the
regulator must be disconnected before moving the
appliance. If the range is equipped with a warmer
drawer, the regulator can be accessed through a side
panel. Remove the 2 screws securing the panel, then
remove the panel. Disconnect the regulator from the
piping. Reassemble in reverse order (see Figure 8).

Range Installation

When unpacking the range, do not
discard the 2 front shipping bolts, but screw them into
the holes at the front corners of the range; they will
function as the front leveling legs. Discard the 2 other
(Models with an Electric Oven and a Gas Cooktop)
bolts; they are not needed, and are installed on the
range for shipping purposes only. This appliance is
equipped with a new system rear leveling system that
allows you to level the range after installation in cutout
opening.
Installation Without Side Panel(s)
For models equipped with Leveling Device:
1. The range cooktop overlaps the countertop at the
sides and the range rests on the floor. The cooktop is
30" (76.2 cm) wide.
2. Install base cabinets 29" (73.7 cm) apart. Make sure
they are plumb and level before attaching cooktop.
Shave raised countertop edge to clear 30" wide
range top rim.
3. Install cabinet doors 31" (78.7 cm) min. apart so it
will not interfere with range door opening.
4. Cutout countertop exactly as shown on page 1.
5. A backguard kit can be ordered through Sears
Service Center.
6. When you unpack the range, the leveling devices
at rear are at the highest position they can be. Make
sure the front leveling legs are also at their highest
position.
7. Install the anti-tip bracket at this
point before placing the range at its final
position. Follow the installation instructions on page
10 or on the anti-tip bracket template supplied with
the range.
8. Slide the range into the cutout opening.
9. Level the range (figure 9). The floor where the
range is to be installed must be level. Follow the
instructions under "Leveling the Range - Models
Equipped with Leveling Device."
Installation Without Side Panel(s)
For models equipped with Leveling Legs:
1. Follow steps 1 to 5 from the previous "Installation
Without Side panel(s) For models equipped with
Leveling Device."
7
Figure 8