ExSilent QLeaf Lite Quick Start Manual

Contents of the package
Module Qleaf Lite
1 1
Introduction set of soft tips
2
made of hypoallergenic material
(S open en closed version,
M and L closed version)
Battery (type 10) 4
3
Battery ejection tool
4
5 Box
6 Quick start guide
L
2
M
3
S
3 Placing the module in the soft tip (step 2)
Push the module gradually into the soft tip. Insert the module all the way into
the soft tip. The device is now ready for use.
5 Cutting the soft tip
When the device is placed properly in the ear, a small part of the pull cord will
usually be visible. You are able to cut a few ribs off the pull cord with a pair of
scissors. Always leave a minimum of 2 ribs, for easy removal of the soft tip from
the ear.
Tips for optimal use
• In order to get accustomed to the Qleaf Lite we advise a continuous
wearing period of one hour, in case of first use. Subsequently, increase
the wearing time one hour each day. The eventual wearing time per day
will vary due to situation(s) in which you need the device. It's important
to increase usage time slowly due to the possibility of hearing certain
sounds such as the rustling of paper, flushing the toilet etc. After 10 to 14
days, your brain will be accustomed to the new sounds; they will become
less conspicuous. You will also be less aware you are using a personal
sound amplifier.
• Clean the device daily after use. Check 'Cleaning the Qleaf Lite' at the
backside of the quick start guide.
• If the battery is almost dead, the device will indicate this every 10 minutes
with a series of double beeps. Replace the battery in a timely manner and
make sure you always have an accessible spare battery.
1
Placing the battery and switching the module on
First remove the sticker from the battery. Place the battery in the module with the
(+) sign (this is the flat side of the battery where the sticker was) at the same side
5
as the (+) sign on the module. The module is set to program 1.
6
4 Placing the device in the ear
A Place the device in the ear with the 'pull cord' (long part of the soft tip) at
the side of the 'tragus' .
your ear. Pull the ear up a little as this will straighten the ear canal, which makes
A
6 Switching programs with the AirTAP
Switch programs with the AirTAP™ functionality by softly tapping the ear twice
(with approximately half a second in between the two taps). It is important
that the ear is closed off with the fingers, so that the device properly notes the
difference in air pressure. The number of beeps indicates which program is in use *.
* Check 'Use of different listening programs' on the backside of the
quick start guide.
Removing the device from the ear
Hold the pull cord between your thumb and index
finger and pull the device gradually from the ear.
B
Move you arm over your head. Grab the upper part of
'tragus'
'pull cord'
functionality
™


Removing the device from the
soft tip
Pull the pull cord down to release the module. Take
the module out of the soft tip.
2
Placing the module in the soft tip (step 1)
Start with a 'medium' soft tip*. Hold the soft tip with the pull cord pointed
upwards. Place the module in the soft tip with the arrow facing towards you.
* Check 'troubleshooting' at the backside of the quick start guide if the soft tip
doesn't fit correctly.
it easier to insert the device further. C While pulling the ear up, push the device
gently with an up and down movement as far in the ear as possible.
B C
7

Using the telephone

Switch the device to program 3 .
Hold the phone against your ear at
the front, but keep the phone a little
further away (about 45°) from your
ear at the back.
Turning the device off or replacing
a battery
Switch the device off by pushing the battery out through
the small round opening, at the long (under) side of the
device, with the supplied battery eject tool. To insert a
(new) battery, check step
45°
1 placing the battery.