Related Manuals for Brice 330IK
Summary of Contents for Brice 330IK
- Page 1 ™ ™ Operation and Safety Manual Model Model 330IK 330IK Manual Gear Driven Gravity Feed Slicer...
-
Page 2: Safety Issues
SAFETY ISSUES 1. NEVER touch this machine without training and authorisation from your supervisor. 2. Machine MUST BE on solid, level bench/table. 3. Guards MUST BE in place before plugging in and turning on machine. 4. ALWAYS use the three-pronged plug provided. 5. - Page 3 A word to the wise This Manual is really two sets of instructions in one - some sections are relevant to all Brice slicers, while other sections only concern a particular slicer or range of slicers.
- Page 4 WHENEVER YOU CARRY OUT ANY PROCEDURE THAT PLACES YOUR HANDS ON OR NEAR THE SLICER BLADE YOU MUST WEAR SUITABLE PROTECTIVE HAND COVERINGS SUCH AS STEEL MESH GLOVES TO PREVENT ACCIDENTAL INJURY FROM THE BLADE. 1.2 Introduction Model 330IK Manual Gear Driven Gravity Feed Slicer...
-
Page 5: Installing The Slicer
Operation and Safety Manual ™ The Brice Model 330IK manual slicer has been designed for environments where a range of The Brice Model different foodstuffs and slicing requirements must be met - from individual slices to large batches. Its features include: 330IK Gear •... - Page 6 180˚ clockwise. Return the sharpener to its storage position. 11. Turn off the blade motor by pressing the red OFF button. 1.4 Introduction Model 330IK Manual Gear Driven Gravity Feed Slicer...
-
Page 7: Operation
7. When you have finished slicing, make sure that the meat table is pulled to the front of the slicer and switch off the power by pressing the red OFF button. Model 330IK Manual Gear Driven Gravity Feed Slicer Operation 2.1... - Page 8 2. Swing the meat grip (12) over and press down to insert spikes into the foodstuff about to be sliced. The meat grip is not always required, if the foodstuff is heavy enough to self feed down the meat tray. 2.2 Operation Model 330IK Manual Gear Driven Gravity Feed Slicer...
-
Page 9: Cleaning The Slicer
This section deals with cleaning your slicer, including blade cleaning. Cleaning the We recommend that, before cleaning or maintenance tasks are undertaken, the machine operator(s) receive some training from authorised Brice representatives, preferably during Slicer the installation phase. Before carrying out cleaning or maintenance tasks, it is very important that: 1. -
Page 10: Cleaning Schedule
���� ��� ���� ��� The cleaning schedule ���� ���� ������� ������ ���� ����� � ������ ����� ���� ���� ��� ������� �������� ��� ������������ ����� ��� �������� ��������� ����� ������������ �������� 3.2 Cleaning Model 330IK Manual Gear Driven Gravity Feed Slicer... -
Page 11: Routine Maintenance
This section deals with routine maintenance for your slicer, including blade sharpening. Maintenance We recommend that, before cleaning or maintenance tasks are undertaken, the machine operator(s) receive some training from authorised Brice representatives, preferably during the installation phase. Before carrying out cleaning or maintenance tasks, it is very important that: 1. -
Page 12: Blade Sharpening
2. The sharpener cannot function properly once the blade diameter has been reduced by more than 10mm. Contact your authorised Brice technician to arrange for a replacement once the blade wears to this point. To sharpen the blade: 1. -
Page 13: Electrical Safety
™ Electrical safety The 330IK is fitted with safety cut-out switches that will automatically stop the machine if, while running, the blade cover securing knob is released or the blade binds or jams. If any of these events occurs, either replace the relevant component or disconnect the slicer from the power supply, clear the jam and switch the machine back on. -
Page 14: Copyright Information
This document may not be reproduced, in whole or in part, by any means without the prior express written permission of the copy- right owner. Brice and the BRICE logotype are trademarks of Brice Australia Pty. Ltd. Printed in Australia...