Electrolux EDW 1003 Service Manual page 31

6.11. Customer function / setting of water hardness
General information
w Setting and changing the water hardness area is executed in
all designs resp. key arrangements analogously.
w For that you always have to use the keys S0, S1, S2 and S3
independent of their variant-depending program load.
w Key S1 is ALWAYS the "water hardness area key"
w Water hardness area 4 is preset by the manufacturer.
With setting "1L" it is generally not regenerated.
A salt addition is not necessary.
w A possible existing "salt" LED is not selected.
Electronic and mechanical setting with the appliance:
w Next to the "electronic" setting on the control panel described
at the right you also have to pay attention to the mechanical
setting in the appliance by the 2-step blending switch.
(see for that the table for hardness area values)
EDW 1003 / VGA
LD1 LD2 LD3
S1 S2 S3
Table for hardness area values:
Anzeige Einstellung der
Wasserhärte
Ende-LED Härtestufe
Anzahl blinken
elektronisch mechanisch in dH
akustisch
1 mal 1 bis 4
2 mal 2 4 bis 10
3 mal 3 11 bis 14
0
4 mal 4 15 bis 18
5 mal 19 bis 22
5
6 mal 23 bis 28
6
7 mal 7 29 bis 36
8 mal 8 37 bis 42
a
1
9 mal 9 43 bis 50
10 mal 10 51 bis 70
Calling / changing / saving the "electronic" hardness area value
1.
2.
3.
4.
Verschneide-
schalter
ENDE
S0
LD1
... AUS nach 60sek. automatisc h
Bemerkung
in mmol/L Bereich
bis 0,7 I kein Regenerieren
0,7 bis 1,8 I / II
1,9 bis 2,5 II
2,6 bis 3,2
III
3,3 bis 3,9
4,0 bis 5,0
5,1 bis 6,4
6,5 bis 7,5 IV
7,6 bis 8,9
9,0 bis 12,5 doppelt Regenerieren
LD1 LD2 LD3 LD4 LD5 LD6
LD7 LD10
LD8 LD11
LD9 LD12
S1 S2 S3 S4 S5 S6
LD1 LD2 LD3 LD4 LD5 LD6
blinken
LD1 LD2 LD3
S2 S3
blinkt codiertes blinken!
LD1
ENDE
S1
blinkt codiertes blinken!
Pr o
LD1
Tastendr u c k
+ 1 Stufe
ENDE
S1
blinkt codiertes blinken!
LD1
ENDE
LD2 LD3 LD4 LD5 LD6
S0
... AUS durch manuelle Betätigung über Ein/Aus
31
Calling the function "set water hardness"
he 1. Appliance in switched-off condition
S0
2. Switch on appliance by ON/OFF key S0 -- "prestart" mode
Ä All LEDs of program and option keys are lit.
S0
3. Press keys S2 and S3 simultaneously until the
confirmation LEDs LD1, LD2 and LD3 are flashing
4. By actuating the function key S1 you now can call the
water hardness function. The confirmation LED LD1
continues flashing, LEDs LD2 and LD3 go out.
The set hardness area is indicated optically by the coded
flashing of the "END" LED and in addition acoustically.
( see for that the table on the left side of this page! )
Changing the set hardness
Any further actuation of the function key S1 changes
the hardness area. This increases the value scrolling.
Leaving the function
After pressing the function key S1 last you can leave
the special program as follows.
After 60 seconds all LEDs of program and option keys will
be lit automatically. The indication in the display goes out.
Now the appliance is again in the "prestart" mode
or
S0
the appliance is switched off by the ON/OFF key S0.
Saving the set water hardness
The selected hardness area is saved directly
after every entry.