NAP 100 Installation and Operation Loudspeaker Cable and Connectors 16.1 General Connections Notes NAP 500 Connections 16.2 Protection Notes NAP 500 Connected to NAP 500PS 16.3 Loudspeaker Cable and Connectors NAP 100 Connections NAP 300 Installation and Operation 17.1 NAP 100 Rear...
I ntro ducti o n Naim Audio products are conceived with performance as the top priority. Careful Note: Please read installation will help ensure that their full potential is achieved. This manual covers the Statutory Safety all power amplifiers. It begins with some general installation notes. Product specific Warnings found at the information begins in Section 4.
3.5 L ig htni ng Precaut i ons power supplies and power amplifiers should be located a Your Naim hi-fi system can be damaged by lightning and should reasonable distance away from other equipment. The maximum be turned off and disconnected from the mains when there is separation distance for connected equipment is that allowed by risk of lightning strike.
Switch on the source and preamplifier components, with the volume turned down, before switching on the NAP 500. The NAP 500 power button is located on the front panel of the NAP 500PS Power Supply.
Page 6
N A P 5 00 5 NAP 500 Con nect io ns 5.1 NAP 500 Conne c te d to N AP 500 P S signal signal left right input ch2(R) input ch1 (L) speaker speaker mains input and fuse...
Page 7
6.3 Loudspeaker Cable and Connectors The negative input and output connections for each channel are Only Naim Audio speaker cable should be used to connect a common. The mains earth (ground) should always be connected loudspeaker to the output of the NAP 300. Custom Naim Audio...
Page 8
N A P 3 00 7 NA P 300 Co nnect io ns 7.1 NAP 300 Conn e cte d to N AP 300P S signal left right signal input ch1(L) input ch2(R) speaker speaker mains input and fuse Input Ch1 Input Ch2 Interconnect Cables cable...
Page 9
In order to avoid hum loops, the signal Only Naim Audio speaker cable should be used to connect a negative of the whole system should be connected to the mains loudspeaker to the output of the NAP 250.
Page 10
10.3 Loudspeaker Cable and Connectors to the signal negative. In order to avoid hum loops, the signal Only Naim Audio speaker cable should be used to connect a negative of the whole system should be connected to the mains loudspeaker to the output of the NAPV 145. Custom Naim Audio earth (ground) in one place.
Page 11
NAP 200. The NAP 200 power button is located on the front panel. The NAP 200 can provide power for an appropriate Naim Audio preamplifier. The power supply output is carried on the DIN input socket.
Page 12
NAP 155 XS. The NAP 155 XS power switch is located on the rear panel. The NAP 155 XS can provide power for an appropriate Naim Audio preamplifier. The power supply output is carried on the DIN input socket.
Page 13
European safety regulations these should always be used. Naim Audio speaker cable will provide the best results; however, 1 6. 2 Prote ct i on Note s a wide range of speaker cable types can be used without risk of Once installed the NAP 100 is intended to remain permanently damage to the amplifier.
None None None Dimensions (H x W x D): NAP 500 - 160 x 432 x 375mm NAP 300 - 87 x 432 x 314mm 87 x 432 x 314mm NAP 500PS - 87 x 432 x 314mm NAP 300PS - 87 x 432 x 314mm...
D e cl a r a t i on o f Co nfo r m it y 1 9 D ec la r at io n of Co nfo r mit y Naim Audio declares that Naim Audio products are in conformance with: Low Voltage Directive 2006/95/EC...