Related Manuals for NAIM NAP 150 - ISSUE 1
Summary of Contents for NAIM NAP 150 - ISSUE 1
- Page 1 W O R L D C L A S S H I F I O W N E R S M A N U A L I S S U E 1 Power amplifiers: NAP 500, NAP 300, NAP 250, NAP V145, NAP 200, NAP 150, NAP V175...
-
Page 2: Table Of Contents
3.5 if you have a problem 1 Equipment Installation 4 Warnings Normally your Naim equipment will have been installed by the dealer who sold it to you 5 Connection 5.1 mains lead even if you live outside their immediate vicinity. Your dealer is responsible for making 5.2 non-rewireable mains... -
Page 3: Mains Supply
In most territories a dealer must be prepared to take back improve system performance. any Naim equipment he has sold you if he cannot make it work to your satisfaction in your own home. A problem may Do not wire voltage dependent resistors or noise be due to a fault in any part of the system or its suppressors into mains plugs. -
Page 4: Connection
Use of non-standard speaker cables or interconnects may correct replacement must be obtained from your dealer, or invalidate your guarantee. from Naim Audio direct. Do not use the plug until the fuse carrier is replaced. 5.4 plug fuses Replace only with ASTA or BS 1362 approved fuses. -
Page 5: Nap 500
Only Naim Audio speaker cable should be used to connect channel are common. The mains earth (ground) should a loudspeaker to the output of the NAP 500. Custom Naim always be connected regardless of what other equipment is Audio loudspeaker connectors are supplied to make the used in conjunction with Naim power amplifiers. -
Page 6: 7 Nap 500 Connection
NAP 500 Connection & Specifications 7.1 NAP 500 connection to NA PS500 Power Supply to preamp power right to preamp power left supply. left, ch1 speaker ch2 supply. right, ch2 speaker ch1 NA PS500 rear mains in Input Socket 1 Input Socket 2 7.2 Specifications NAP 500 &... - Page 7 THE CASE. THE VOLUME SHOULD BE REDUCED. 8.3 loudspeaker cable and connectors Only Naim Audio speaker cable should be used to connect a loudspeaker to the output of the NAP 300. Custom Naim Audio loudspeaker connectors are supplied to make the connection.
- Page 8 NAP 300 Connection & Specifications 9.1 NAP 300 connection to NA PS300 Power Supply to preamp left right to preamp power speaker ch1 speaker ch2 power supply. supply. left, ch1 right, ch2 NA PS300 rear mains in Input Socket 1 Input Socket 2 9.2 Specifications NAP 300 &...
- Page 9 THE CASE. THE VOLUME SHOULD BE REDUCED. 10.3 loudspeaker cable and connectors Only Naim Audio speaker cable should be used to connect a loudspeaker to the output of the NAP 250. Custom Naim Audio loudspeaker connectors are supplied to make the connection.
-
Page 10: Nap 250 Connection
NAP 250 Connection & Specifications 11.1 NAP 250 Rear mains in left right to preamplifier speaker ch1 speaker ch2 power supply 11.2 Specifications Input socket NAP 250 Power Output: ch 1 Continuous, 8 ohms 80 Watts per channel Transient 400 VA Quiescent Power Consumption 25VA Voltage Gain... - Page 11 THE CASE. THE VOLUME SHOULD BE REDUCED. 12.3 loudspeaker cable and connectors Only Naim Audio speaker cable should be used to connect a loudspeaker to the output of the NAP V145. Custom Naim Audio loudspeaker connectors are supplied to make the connection.
-
Page 12: Nap V145 Connection
NAP V145 Connection & Specifications 13.1 NAP V145 Rear mains in to preamplifier speaker output power supply 13.2 Specifications Input socket NAP V145 Power Output: Continuous, 8 ohms 80 Watts Transient 400 VA Quiescent Power Consumption 15VA Voltage Gain +29dB Input Impedance 18 kilohms Frequency response... - Page 13 The NAP 150 power button is located on the rear panel. Both the NAP 200 and NAP 150 can provide power for an appropriate Naim Audio preamplifier. The power supply output is carried on the DIN input socket.
- Page 14 NAP 200 & NAP 150 Connection & Specifications 15.1 NAP 200 Rear mains in left right to preamplifier or speaker ch1 speaker ch2 power supply 15.2 Specifications Input socket NAP 200 Power Output: ch 2 Continuous, 8 ohms 70 Watts per channel Transient 300 VA Quiescent Power Consumption...
- Page 15 THE CASE. THE VOLUME SHOULD BE REDUCED. 16.3 loudspeaker cable and connectors Only Naim Audio speaker cable should be used to connect a loudspeaker to the output of the NAP V175. Custom Naim Audio loudspeaker connectors are supplied to make the connection.
-
Page 16: Nap V175 Connection
NAP V175 Connection & Specifications 17.1 NAP V175 Rear power mains to a/v processor left right speaker centre speaker speaker Input Socket 1 Input Socket 2 17.2 Specifications NAP V175 Power Output: Continuous, 8 ohms 50 Watts per channel Quiescent Power Consumption 13VA Channels Three... - Page 17 Declaration of conformity to appropriate standards Manufacturer Naim Audio Limited, Southampton Road, Salisbury, England, SP1 2LN Products NAP 500, NA PS500, NAP 300, NA PS300, NAP 250, NAP V145, NAP 200, NAP 150, NAP V175 Safety HD 195-S6 EN 60 065...
- Page 18 Naim Audio Limited, Southampton Road, Salisbury, England SP1 2LN Part No. OWMPA 12-001-0038 DRG No. NA202001-400 Telephone: +44 (0) 1722 332266 Fax: +44 (0) 1722 412034 www.naim-audio.com...