Sanyo DP19649 Service Manual page 17

2-2: BRIGHTNESS CENT
1. Place the set in Aging Test for more than 30 minutes.
2. Receive the color bar pattern. (RF Input)
3. Using the remote control, set the brightness and
contrast to normal position.
4. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (32) on the remote control to
select "BRIGHTNESS CENT".
5. Press the VOL.UP/DOWN button on the remote control
until the contrast step No. becomes "130".
6. Check if the picture is normal.
7. Receive the color bar pattern. (VIDEO Input)
8. Using the remote control, set the brightness and
contrast to normal position.
9. Press the INPUT SELECT button on the remote
control to set to the AV mode.
10.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (32) on the remote control to
select "BRIGHTNESS CENT".
11.
Press the VOL.UP/DOWN button on the remote control
until the contrast step No. becomes "1131".
12.
Check if the picture is normal.
13.
Receive the color bar pattern. (S-VIDEO Input)
14.
Using the remote control, set the brightness and
contrast to normal position. co t ast to o a pos t o
15. Press the INPUT SELECT button on the remote
control to set to the AV(Y/C) mode. Then perform the
above adjustments 10~12.
16. Playback the DVD(480i) disc. (COMPONENT Input)
17. Using the remote control, set the brightness and
contrast to normal position.
18. Press the INPUT SELECT button on the remote
control to set to the COMPONENT mode.
19.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (32) on the remote control to
select "BRIGHTNESS CENT".
20. Press the VOL.UP/DOWNbutton on the remote control
until the contrast step No. becomes "132".
21. Check if the picture is normal.
22. Playback the DVD(480i) disc. (HDMI Input)
23. Using the remote control, set the brightness and
contrast to normal position.
24. Press the INPUT SELECT button on the remote
control to set to the HDMI mode.
25.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (32) on the remote control to
select "BRIGHTNESS CENT".
26. Press the VOL.UP/DOWNbutton on the remote control
until the contrast step No. becomes "127".
27. Check if the picture is normal.
ELECTRICAL ADJUSTMENTS
D-2
D-2
2-3: CONTRAST MAX
1. Place the set in Aging Test for more than 30 minutes.
2. Receive the color bar pattern. (RF Input)
3. Using the remote control, set the brightness and
contrast to normal position.
4. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (51) on the remote control to
select "CONTRAST MAX".
5. Press the VOL.UP/DOWN button on the remote control
until the contrast step No. becomes "140".
6. Check if the picture is normal.
7. Receive the color bar pattern. (VIDEO Input)
8. Using the remote control, set the brightness and
contrast to normal position.
9. Press the INPUT SELECT button on the remote
control to set to the AV mode.
10. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (51) on the remote control to
select "CONTRAST MAX".
11. Press the VOL.UP/DOWN button on the remote control
until the contrast step No. becomes "146".
12. Check if the picture is normal.
13. Receive the color bar pattern. (S-VIDEO Input)
14. Using the remote control, set the brightness and
co t ast to o contrast to normal position. a pos t o
15. Press the INPUT SELECT button on the remote
control to set to the AV(Y/C) mode. Then perform the
above adjustments 10~12.
16. Playback the DVD(480i) disc. (COMPONENT Input)
17. Using the remote control, set the brightness and
contrast to normal position.
18. Press the INPUT SELECT button on the remote
control to set to the COMPONENT mode.
19. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (51) on the remote control to
select "CONTRAST MAX".
20. Press the VOL.UP/DOWN button on the remote control
until the contrast step No. becomes "142".
21. Check if the picture is normal.
22. Playback the DVD(480i) disc. (HDMI Input)
23. Using the remote control, set the brightness and
contrast to normal position.
24. Press the INPUT SELECT button on the remote
control to set to the HDMI mode.
25. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (51) on the remote control to
select "CONTRAST MAX".
26. Press the VOL.UP/DOWNbutton on the remote control
until the contrast step No. becomes "117".
27. Check if the picture is normal.