INDEX page INTRODUCTION/GENERAL INSTRUCTION ......1-2 TECHNICAL SPECIFICATION ..........3 DESCRIPTION OF CONTROLS..........4-5 PREPARING A NEW MACHINE..........6-7 PREPARATION FOR USE ..........8-11 USING THE MACHINE ..........12-16 AUTOMATIC CHANGING OF BRUSHES.......17 USER MAINTENANCE...........18-20 EMERGENCY AND AUXILIARY CONTROLS......21 ACCESSORIES ..............22 ERROR CODE MEANINGS..........23...
ELECTROLUX EUROCLEAN or your local distributor. MODIFICATIONS AND IMPROVEMENTS Electrolux Euroclean aim toward continuous improvement of its machines and reserves the right to carry out modiﬁcations and improvements whenever necessary without being obliged to update machines which have been sold previously.
- If the machine does not work properly, check by conducting simple maintenance procedures. (shut-off) Otherwise, it is better to ask for technical service. - Where spare parts are required contact ELECTROLUX EUROCLEAN or a local distributor for Faulty accelerator potentiometer Replace potentiometer genuine original parts, or ask for on site technical service.
1. Battery supplied and ﬁtted, ﬁlled with acid and ready for use. 2. Battery supplied and ﬁtted but dry. 3. Battery obtainable locally by customer. TECHNICAL SPECIFICATION MODELS AR 4090 AR 4100 Working width (mm) 1000 Width of squeegee (mm) 1130 1280 No. of brushes...
DESCRIPTION OF CONTROLS EMERGENCY AND AUXILIARY CONTROLS EMERGENCY STOP BUTTON In the event of an emergency hit the button, all controls are killed and the machine stops. To reset, turn in the direction of the arrow to release the button. ERROR SPEED CODE...
USER MAINTENANCE DESCRIPTION OF CONTROLS WARNING: The machine must be switched off and the battery unplugged. 1 - Forward speed selector 2 - Traction motor overload indicator 3 - Automatic brush changing selector Remove the inner plastic cover to gain access to 4 - Brush unlock the electrical panel.
PREPARING A NEW MACHINE USER MAINTENANCE The machine is battery operated. WARNING: The machine must be switched off and the battery unplugged. Depending on the country in which the machine is supplied three options are possible: Remove each solenoid assembly one at a time, by 1.
USER MAINTENANCE PREPARING A NEW MACHINE WARNING: The machine must be switched off and the battery unplugged. Take special care when handling acid as it is corrosive, if it should come into contact with skin or eyes, wash abundantly with water and consult a doctor. The batteries should be charged in a well ventilated area with the seat raised, using the charger Unscrew the clean tank ﬁlter and scrub with a stiff supplied or one which matches the battery capacity.
PREPARATION FOR USE AUTOMATIC CHANGING OF BRUSHES Attach the squeegee to its bracket at the rear of Switch all functions off. Turn key-switch on. the machine. Lock the hand nuts down tightly. Press the automatic brush change selector push button. The bracket is slotted so that if the squeegee is hooked around an object it will pull away from the bracket instead of causing more serious...
USING THE MACHINE PREPARATION FOR USE Open the valve by turning its lever in line with the Open the brush doors located either side of the outlet. machine. To quickly empty the tank switch on the key-switch then press the recovery tank discharge pump ON/OFF push.
PREPARATION FOR USE USING THE MACHINE Insert the key and turn clockwise to turn the The squeegee can be adjusted for pressure machine “ON”. against the ﬂoor by turning the lower of the two plastic knobs just above the squeegee bracket. The rake angle can be adjusted to make the squeegee sit fully on the ﬂoor by adjustment of the upper knob.
USING THE MACHINE PREPARATION FOR USE Press the speed button to select one of three Release the tank lid locking clips at both sides of predetermined maximum speeds of 2, 4 or 6 km/ the tank, then lift the lid towards the back of the h (1.2, 2.5, or 5 mph) in the forward direction.
USING THE MACHINE USING THE MACHINE Whilst the machine is being used take note of the If more liquid ﬂow is required then press the boost battery condition indicator, if the red indicator pump ON/OFF push which will double the lights continuously then the machine will shortly amount of ﬂow which is shown by the indicator.