Sony HCD-GPX9 Service Manual page 2

HCD-GPX9
QQ
3 7 63 1515 0
DAB frequency table
Band-III
Frequency Label Frequency
174.928 MHz 5A 209.936 MHz
176.640 MHz 5B 211.648 MHz
178.352 MHz 5C 213.360 MHz
180.064 MHz 5D 215.072 MHz
181.936 MHz 6A 216.928 MHz
183.648 MHz 6B 218.640 MHz
185.360 MHz 6C 220.352 MHz
187.072 MHz 6D 222.064 MHz
188.928 MHz 7A 223.936 MHz
190.640 MHz 7B 225.648 MHz
192.352 MHz 7C 227.360 MHz
194.064 MHz 7D 229.072 MHz
195.936 MHz 8A 230.784 MHz
197.648 MHz 8B 232.496 MHz
199.360 MHz 8C 234.208 MHz
201.072 MHz 8D 235.776 MHz
202.928 MHz 9A 237.488 MHz
204.640 MHz 9B 239.200 MHz
206.352 MHz 9C
208.064 MHz 9D
Note
Frequencies are displayed to two places of decimals on
this system.
L-Band
Frequency Label
TE
L 13942296513
1452.960 MHz L1
1454.672 MHz L2
1456.384 MHz L3
1458.096 MHz L4
1459.808 MHz L5
1461.520 MHz L6
1463.232 MHz L7
1464.944 MHz L8
1466.656 MHz L9
1468.368 MHz L10
1470.080 MHz L11
1471.792 MHz L12
1473.504 MHz L13
1475.216 MHz L14
1476.928 MHz L15
1478.640 MHz L16
1480.352 MHz L17
1482.064 MHz L18
1483.776 MHz L19
1485.488 MHz L20
1487.200 MHz L21
1488.912 MHz L22
1490.624 MHz L23
Notes
• L-Band is not available for the UK model.
• Frequencies are displayed to two places of decimals
on this system.
www
.
2
http://www.xiaoyu163.com
Label
10A
10B
10C
10D
11A
11B
11C
11D
12A
12B
12C
12D
13A
13B
13C
13D
13E
13F
x ao u163
y
i
http://www.xiaoyu163.com
2 9
8
General
Power requirements
230 V AC, 50/60 Hz
Power consumption 85 W
0.25 W (in Power Saving
Mode)
Dimensions (w/h/d) Approx. 181.5 × 261.5 ×
357.5 mm incl. projecting
parts and controls
Mass Approx. 5.8 kg
Design and specifications are subject to change
without notice.
Q Q
3 6 7 1 3 1 5
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.r may be damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ∞C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
This appliance is classified as
a CLASS 1 LASER product.
The CLASS 1 LASER
PRODUCT MARKING is
located on the rear exterior.
co
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
.
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
9 4 2 8
0 5 8 2 9 9 4 2 8
m
9 9
9 9