Remote Control Code - Panasonic SC-HC29 Operating Instructions Manual

█
Main unit displays
"--:--"
• You connected the AC mains lead for the first time or there
was a power failure recently. Set the clock.
"ADJUST CLOCK"
• The clock is not set. Adjust the clock.
"ADJUST TIMER"
• The play timer is not set. Adjust the play timer.
"AUTO OFF"
• The system has not been used for 20 minutes and will
switch off within a minute. To cancel, press any button.
"ERROR"
• An incorrect operation was done. Read the instructions and
try again.
"F61"
"F77"
• Disconnect the AC mains lead and consult your dealer.
"F70"
• Examine the Bluetooth
• Disconnect the Bluetooth
and then switch on again.
"F76"
• There is a problem with the power supply.
• Disconnect the AC mains lead and consult your dealer.
"ILLEGAL OPEN"
• The sliding door is not in a correct position. Switch off the
system and then switch on again.
"NODEVICE"
• The USB device is not connected. Examine the connection.
"NO DISC"
• You have not put in a disc.
"NO PLAY"
• Examine the content. You can only play supported format.
• The system may have a problem. Switch off the system and
then switch on again.
"PLAYERROR"
•
You played an unsupported MP3 file. The system will skip
that track and play the next one.
"REMOTE 1"
"REMOTE 2"
• The remote control and the main unit are using different
codes. Change the code of the remote control.
SC-HC29
– When "REMOTE 1" is shown, press and hold [OK] and
[ ] for a minimum of 4 seconds.
– When "REMOTE 2" is shown, press and hold [OK] and
[USB/CD] for a minimum of 4 seconds.
SC-HC19
– When "REMOTE 1" is shown, press and hold [OK] and
[RADIO] for a minimum of 4 seconds.
– When "REMOTE 2" is shown, press and hold [OK] and
[CD] for a minimum of 4 seconds.
"USB OVER CURRENT ERROR"
• The USB device is using too much power. Disconnect
the USB device, switch off the system and then switch on
again.
"VBR–"
• The system cannot show the remaining play time for
variable bit rate (VBR) tracks.
14
® device.
®
device. Switch off the system

Remote control code

When other Panasonic equipment responds to the
remote control of this system, change the remote control
code for this system.
Preparation
SC-HC29
Press [USB/CD] to select "CD".
SC-HC19
Press [CD].
█
To set the code to "REMOTE 2"
SC-HC29
1
Press and hold [SELECTOR] on the main unit and
[USB/CD] on the remote control.
"REMOTE 2" is shown.
2
Press and hold [OK] and [USB/CD] for a minimum of
4 seconds.
SC-HC19
1
Press and hold [SELECTOR] on the main unit and
[CD] on the remote control.
"REMOTE 2" is shown.
2
Press and hold [OK] and [CD] for a minimum of
4 seconds.
█
To set the code to "REMOTE 1"
SC-HC29
1
Press and hold [SELECTOR] on the main unit and
[ ] on the remote control.
"REMOTE 1" is shown.
2
Press and hold [OK] and [ ] for a minimum of
4 seconds.
SC-HC19
1
Press and hold [SELECTOR] on the main unit and
[RADIO] on the remote control.
"REMOTE 1" is shown.
2
Press and hold [OK] and [RADIO] for a minimum of
4 seconds.
System memory reset
Reset the memory when the following situations occur:
• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.
1
Disconnect the AC mains lead.
2
While you press and hold [1] on the main unit,
connect the AC mains lead again.
Continue to press and hold the button until
"– – – – – – – –" is shown.
3
Release [1].
All the settings are set back to the factory preset.
It is necessary to set the memory items again.