Remote Control Code - Panasonic SC-AKX320 Operating Instructions Manual

Hide thumbs Also See for SC-AKX320:
Table of Contents

Advertisement

Available languages

Available languages

  • ENGLISH, page 1
█ Main unit displays
"--:--"
• You connected the AC mains lead for the first time or there
was a power failure recently. Set the clock.
• Track play time is more than 99 minutes.
"ADJUST CLOCK"
• The clock is not set. Adjust the clock.
"ADJUST TIMER"
• The play timer is not set. Adjust the play timer.
"AUTO OFF"
• The system has not been used for 20 minutes and will
switch off within a minute. To cancel, press any button.
"ERROR"
• An incorrect operation was done. Read the instructions and
try again.
"F" / "F" ("" represents a number.)
• The protection circuit has been activated and the system
may be switched off automatically.
• Disconnect the AC mains lead and wait for a few seconds
before connecting it again. If the problem persists,
disconnect the AC mains lead and consult your dealer.
"NO DISC"
• You have not put in a disc.
"NO PLAY"
"UNSUPPORT"
• There is no album or track in the USB device.
• Examine the content. You can only play supported format.
• The system may have a problem. Switch off the system and
then switch on again.
"PLAYERROR"
• An unsupported MP3 file has been played. The system will
skip that track and play the next one.
"REMOTE 1"
"REMOTE 2"
• The remote control and the main unit are using different
codes. Change the code of the remote control.
– When "REMOTE 1" is shown, press and hold [OK] and [
on the remote control for a minimum of 4 seconds.
– When "REMOTE 2" is shown, press and hold [OK] and [<]
for a minimum of 4 seconds.
"TEMP NG"
• The temperature protection circuit has been activated, and
the system will switch off. Let the unit cool down before
switching it on again.
• Check that the ventilation opening of the unit is not
obstructed.
• Ensure this unit is well ventilated.
"USB A NO DEVICE"
"USB B NO DEVICE"
• The USB device is not connected. Examine the connection.
"USB OVER CURRENT ERROR"
• The USB device is drawing too much power. Disconnect the
USB device, switch off the system and then switch on again.
• Check the connection, it may be caused by a faulty USB
cable.
"VBR"
• The system cannot show the remaining play time for variable
bit rate (VBR) tracks.
14
14

Remote control code

When other Panasonic equipment responds to the remote
control of this system, change the remote control code for
this system.
Preparation
Press [SELECT] repeatedly on the main unit to select
"AUX".
█ To set the code to "REMOTE 2"
1
Press and hold [SELECT] on the main unit and [<]
until "REMOTE 2" is shown.
2
Press and hold [OK] and [<] for a minimum of
4 seconds.
█ To set the code to "REMOTE 1"
1
Press and hold [SELECT] on the main unit and [
on the remote control until "REMOTE 1" is shown.
2
Press and hold [OK] and [
control for a minimum of 4 seconds.
System memory reset
Reset the memory when the following situations occur:
• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.
1
Disconnect the AC mains lead.
2
While you press and hold [1] on the main unit,
connect the AC mains lead again.
Continue to press and hold the button until
"– – – – – – – – –" is shown.
3
]
Release [1].
All the settings are set back to the factory preset.
It is necessary to set the memory items again.
]
] on the remote

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents