Remote Control Code - Panasonic SC-AKX38 Operating Instructions Manual

RQT9895-M_en.fm Page 19 Monday, November 25, 2013 5:51 PM
"ERROR"
• An incorrect operation was done. Read the instructions
and try again.
"ERROR" (during recording)
• You cannot select other playback source (example:
radio, USB etc.) or press [2] or [6] during
recording. Stop the recording function.
• You cannot open the disc tray when recording from an
AM source.
"F61"
• Examine and correct the speaker cords connection.
• Disconnect the USB device. Switch off the system and
then switch it on again.
"F70"
• Examine the Bluetooth ® connection.
• Disconnect the Bluetooth device. Switch off the
®
system and then switch it on again.
"F76"
• There is a problem with the power supply.
• Disconnect the AC power supply cord and consult your
dealer.
"F77"
• Disconnect the AC power supply cord and consult your
dealer.
"NODEVICE"
• The USB device is not connected. Examine the
connection.
"NO DISC"
• You have not put in a disc.
"NO PLAY"
"UNSUPPORT"
• Examine the content. You can only play supported
format.
• The files in the USB device can be corrupted. Format
the USB device and try again.
"NO TRACK"
• There is no album or track in the USB device or the
internal memory.
• There is no album or track in the USB device.
"NOT MP3 = ERROR"
"PLAYERROR"
• You played an unsupported MP3 file. The system will
skip that track and play the next one.
"RECERROR"
• You disconnected the USB device while recording.
Connect the USB device and do recording again.
"REMOTE 1"
"REMOTE 2"
• The remote control and the main unit are using
different codes. Change the code of the remote
control.
– When "REMOTE 1" is shown, press and hold [OK]
and [ ] for a minimum of 4 seconds.
– When "REMOTE 2" is shown, press and hold [OK]
and [USB/CD] for a minimum of 4 seconds.
Confidential
Until: 28 Jan 2014
Safety application draft
"TEMP NG"
• The temperature protection circuit has been activated,
and the system will switch off. Let the unit cool down
before switching it on again.
• Check that the ventilation opening of the unit is not
obstructed.
• Ensure this unit is well ventilated.
"USB OVER CURRENT ERROR"
• The USB device is using too much power. Disconnect
the USB device, switch off the system and then switch
on again.
"VBR–"
• The system cannot show the remaining play time for
variable bit rate (VBR) tracks.

Remote control code

When other Panasonic equipment responds to the
remote control of this system, change the remote control
code for this system.
Preparation
Press [RADIO/EXT-IN] to select "MUSIC PORT" or
"AUX".
█
To set the code to "REMOTE 2"
1
Press and hold [RADIO/EXT-IN] on the main unit
and [2] on the remote control until "REMOTE 2" is
shown.
2
Press and hold [OK] and [2] for a minimum of 4
seconds.
█
To set the code to "REMOTE 1"
1
Press and hold [RADIO/EXT-IN] on the main unit
and [1] on the remote control until "REMOTE 1" is
shown.
2
Press and hold [OK] and [1] for a minimum of 4
seconds.
System memory reset
Reset the memory when the following situations occur:
• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.
1
Disconnect the AC power supply cord.
2
While you press and hold [1] on the main unit,
connect the AC power supply cord again.
Continue to press and hold the button until
"– – – – – – – –" is shown.
3
Release [1].
All the settings are set back to the factory preset.
It is necessary to set the memory items again.
19