Advertisement
Quick Links
Sec1:1
ACCUSPLIT, Inc.
2290A Ringwood Ave.
San Jose, CA 95131
800-965-2008 • 925-226-0888
FAX 925-463-0147
www.ACCUSPLIT.com
support@ACCUSPLIT.com
ii
Sec1:2-Sec1:3
DISPLAYS
CURRENT DAY
Display
7329
5:18
1
days
MEMORY
2
2
display area
3
57
.
9:58
3
21
.
Mile/h
MEMORY
button
MEMORY
Display
ACCUSPLIT
AH190M28
Operating Instructions
The pedometer has two display modes: CURRENT DAY and
MEMORY.
1. CURRENT DAY display: Display area in lower right of
screen shows SPEEDOMETER function: Mile/h.
2. MEMORY display: Memory display area in lower right
of screen shows which day's results you are viewing.
To enter MEMORY display, fi rst press the yellow MODE
button, then press the gray "M" button. Return to
CURRENT DAY display by repeatedly pressing the gray
"M" button until the memory display area is blank.
Make sure you are in CURRENT DAY display when setting up
your pedometer and checking today's results.
PEDOMETER
1
3
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Accusplit Healthengine AH190M28
Summary of Contents for Accusplit Healthengine AH190M28
- Page 1 Sec1:1 ACCUSPLIT, Inc. 2290A Ringwood Ave. San Jose, CA 95131 800-965-2008 • 925-226-0888 FAX 925-463-0147 www.ACCUSPLIT.com support@ACCUSPLIT.com Sec1:2-Sec1:3 DISPLAYS CURRENT DAY Display 9:58 7329 MEMORY button 5:18 days MEMORY Display MEMORY display area ACCUSPLIT AH190M28 The pedometer has two display modes: CURRENT DAY and MEMORY.
- Page 2 Sec1:4-Sec1:5 SETTING UP YOUR PEDOMETER ACCUSPLIT products use a common setting procedure, S1- S2-S3-S4. Press S1 for 2 seconds: Enter the SET mode Press S2: Change the fi eld to be set Press S3: Change the fi eld value Press S4 for 2 seconds: Exit the SET mode Sec1:6-Sec1:7 1.
- Page 3 Sec1:8-Sec1:9 Setting Your Weight Your body WEIGHT (lbs or kg) must be set to measure your CALORIES burned. 1. S2: You must enter WEIGHT setting mode from CLOCK setting mode, as listed above. Once the clock is set, press the yellow S2 (MODE) button, if you have not done so already, to enter WEIGHT setting mode.
- Page 4 Sec1:12-Sec1:13 Exit Setup Mode Once you have set the time of day, your weight, and your stride length, you have fi nished setting up your pedometer. S4: Press the yellow S4 (MODE) button for at least 2 seconds to return to STEP Mode. The display will stop fl ashing. Sec1:14-Sec1:15 USING YOUR PEDOMETER Wearing Your Pedometer...
- Page 5 Sec1:16-Sec1:17 • DISTANCE mode (ML or KM) displays distance walked or jogged since last automatic daily reset. A line appears under the “DIST” label when in this mode. • STOPWATCH/TIMER mode allows you to display your walking or jogging speed (miles/hr or km/hr), manually record activity time, and use as a countdown timer.
- Page 6 Sec1:20-Sec1:21 7329 5:18 days MEMORY display area Sec1:22-Sec1:23 Using the Speedometer The SPEED function answers the question, “How many sec- onds did I take to walk 10 steps?” (in mph or kph). SPEED is displayed in the lower right hand corner of the display in all modes EXCEPT memory recall.
- Page 7 Sec1:24-Sec1:25 5. To exit stopwatch mode, press the MEMORY button to stop the stopwatch, then press the yellow MODE button to return to STEP mode. 0:14:02 15:01 Mile/h STOPWATCH/TIMER Mode Sec1:26-Sec1:27 4. S2: Press the yellow S2 (MODE) button to switch from the HOUR display to the MINUTE display.
-
Page 8: Additional Information
Sec1:28-Sec1:29 ADDITIONAL INFORMATION Replacing the Battery 1. When the fi gures on the display start to blink, it is time to replace the battery. 2. The unit uses one Type CR2032 3-volt lithium battery. 3. Insert a coin into the slot at the bottom of the body case.
Need help?
Do you have a question about the Healthengine AH190M28 and is the answer not in the manual?
Questions and answers