Table of Contents
Advertisement
PHA+TREM (PHASER+TREMOLO)
Phaser effect followed by Tremolo.
PHASER DEPTH
Range: 0...127
NRPN MSB=3 NRPN LSB=3
Data Entry MSB Range: 0...127
Sets the Phaser's modulation depth.
PHASER SPEED
Range: 0...12 Hz
NRPN MSB=3 NRPN LSB=4
Data Entry MSB Range: 0...127
Sets the Phaser's modulation speed, in Hertz.
PHASER FEEDBACK
Range: 0...127
NRPN MSB=3 NRPN LSB=5
Data Entry MSB Range: 0...127
Sets the quantity of signal that is sent back to the
Phaser input as feedback; in this way the
elaboration development of the signal can be
controlled.
PHASER MANUAL
Range: 0...127
NRPN MSB=3 NRPN LSB=6
Data Entry MSB Range: 0...127
Tune the Phaser modulation manually.
TREMOLO DEPTH
Range: 0...127
NRPN MSB=3 NRPN LSB=7
Data Entry MSB Range: 0...127
Sets the Tremolo's modulation depth.
TREMOLO SPEED
Range: 0...12 Hz
NRPN MSB=3 NRPN LSB=8
Data Entry MSB Range: 0...127
Sets the Tremolo's modulation speed, in Hertz.
TREMOLO PHASE
Range: 0, 180
NRPN MSB=3 NRPN LSB=9
Data Entry MSB Range: 0, 1
Sets the phase of the Tremolo's modulation signal.
TREMOLO SHAPE
Range: 0...127
NRPN MSB=3 NRPN LSB=10
Data Entry MSB Range: 0...127
Modifies the waveform of the Tremolo's modulating
signal, so as to make it softer and smoother on
higher values; the result is a softer effect.
User Manual – Sound generation parameters
WAH-WAH
Simulates the classic guitar effect, that takes the name
from its characteristic sound. It is in short a filter which is
"shifted" along the frequency, so as to create a particular
effect.
TYPE
Range:
Auto: the cutoff frequency moves continuously and
automatically (it is advisable to assign this MIDI
message to a button, to activate/deactivate this
mode).
Touch: the cutoff frequency is set according to the
dynamic, i.e. the pressure on the keyboard. The
higher the dynamic (pressure), the higher the
frequency (it is advisable to assign this MIDI
message to a button, to activate/deactivate this
mode).
Pedal: the cutoff frequency is modified manually (it
is advisable to assign the MIDI message to a pedal,
slider, knob or wheel, to sensibly control the
frequency).
NRPN MSB=3 NRPN LSB=1
Data Entry MSB Range: 16...18
Sets the filter control type.
TOP
Range: 0...127
NRPN MSB=3 NRPN LSB=3
Data Entry MSB Range: 0...127
Sets the filter's maximum cutoff frequency.
BOTTOM
Range: 0...127
NRPN MSB=3 NRPN LSB=4
Data Entry MSB Range: 0...127
Sets the filter's minimum cutoff frequency.
RESONANCE
Range: 0...127
NRPN MSB=3 NRPN LSB=5
Data Entry MSB Range: 0...127
Sets the filter's resonance curve, controlling how the
frequencies close to the cutoff frequency are
magnified. The higher the resonance value, the
narrower the interval in which the frequencies are
magnified; at the same time, the narrower the
interval, the louder are the frequencies within that
interval.
EN - 17
Advertisement
Table of Contents
