Advertisement
PRIMATECH PNEUMATIC NAILER
is a heavy duty precision tool specially developed for the installation
of hardwood flooring. Weighting only 11 pounds (5 kg), this ergono-
mically designed tool makes the installation of hardwood floor very
easy, allowing the operator to set and nail the boards in the standing
position. It uses standard "L" type cleats available in lengths of 1½"
(38 mm), 1¾" (44 mm) or 2" (50 mm) cleats; or optionally the 1½"
(38 mm) or 2" (50 mm) "T" type cleats. For best result, only
P
cleats should be used. For maximum performance, the
RIMATECH
manufacturer guidelines should be followed. Read carefully these
instructions before operating this tool. It is important to understand
warnings/cautions and the safety measures to ensure safe use of
this tool.
Additional information is available directly from the manufacturer:
1135 de Lorraine, Québec, QC
Canada, G1J 1R8
Phone:
1 (800) 363-1962,
Fax:
1 (418) 522-7466
email:
support@primatech.ca
web:
www.primatech.ca/support
SAFETY MEASURES
These important guidelines should always be followed to work safely
with the P
pneumatic nailer model P240:
RIMATECH
1.
Read these instructions thoroughly before using this tool and
keep it handy for reference if necessary.
2.
Always keep hands, feet or other body parts away from the nail
ejection area.
3.
Never aim the tool in any direction other than the working area.
4.
Always carry or manipulate the tool by its handle while the air
supply hose is connected.
5.
Never hit the head cap of the actuator if the plastic base is not
sitting perfectly on the working surface.
6.
Never leave the tool laying down on its side while the air supply
hose is connected; the tool should always be left on the floor,
standing on its plastic base.
7.
Do not alter or remove safety.
8.
Always disconnect the air supply hose when the tool is not in
use or when move to another work area.
P240
1 (418) 522-7744
9.
Never service or repair the tool, clear obstructions or make
adjustments while the air supply hose is connected.
10. Only compressed air should be used to power this tool (110 psi,
7.6 bar maximum).
11. Never use oxygen or any other compressed gas as a power
source for this tool.
12. Always wear OSHA-required Z-87 safety glasses with side
shields.
13. Always wear proper ear and feet protection while the air supply
hose is connected.
D
O NOT REMOVE OR ALTER SAFETY
DEPRESS THE SAFETY CONTACT WITH YOUR HANDS
WHEN TOOL IS CONNECTED TO AIR SUPPLY
CAUTION IS ADVISED WHEN USING THIS TOOL
CONNECTION & AIR SUPPLY SYSTEM
To ensure maximum performance and efficiency, and also a
minimum of care, the P
RIMATECH
dry air. It is necessary to use a filter and a pressure regulator.
This tool needs a detachable male coupler with 3/8" NPT male
treads. Use a 3/8" (1 cm) minimum diameter air supply hose. A
smaller hose or a hose longer than 50' (15 m) could cause a
pressure drop when the tool is activated repeatedly.
A
LWAYS USE A FREE
COMPRESSED AIR SUPPLY TO PREVENT THAT THE
TOOL STAYS CHARGED AFTER DISCONNECTING THE
AIR SUPPLY HOSE
U
NLOAD TOOL BEFORE CONNECTING AIR TO
PREVENT ACCIDENTAL DISCHARGE
A
FTER MOVING TOOL TO A DIFFERENT WORK AREA
OR AFTER ANY MAINTENANCE TO THE TOOL
ENSURE PROPER OPERATION BY ACTUATING TOOL
SEVERAL TIMES WITHOUT CLEATS OVER THE
SUBFLOORING
Dirt, dust, and other particles in the air supply can cause sluggish
operation or premature wear of many components of the tool. Drain
water from the compressor tank regularly. The compressor start-stop
limits should be set to deliver an air pressure of at least 100 psi
(7 bar) at all time. Consult the compressor manual or dealer for
instructions on how to make this adjustment.
. N
EVER
. E
XTREME
.
pneumatic nailer requires clean,
-
FLOW CONNECTION FOR THE
.
.
,
ALWAYS
.
,
Advertisement
