Epson TM-L90 User Manual
  1. Manuals
  2. Brands
  3. Epson Manuals
  4. Printer
  5. TM-L90 series
  6. User manual

Epson TM-L90 User Manual

Thermal printer epson tm-l90
Hide thumbs Also See for TM-L90:
Table of Contents

Advertisement

Quick Links

See also: Service Manual , User Manual
English
Peeler Model
User's Manual
M00075901EN

Advertisement

Table of Contents
loading

Related Manuals for Epson TM-L90

Summary of Contents for Epson TM-L90

  • Page 1 English Peeler Model User’s Manual M00075901EN...
  • Page 2 Seiko Epson Corporation. No patent liability is assumed with respect to the use of the information contained herein. While every precaution has been taken in the preparation of this book, Seiko Epson Corporation assumes no responsibility for errors or omissions.

  • Page 3: Safety Precautions

    Shut down your equipment immediately if it produces smoke, a strange odor, or unusual noise. Continued use may lead to fire. Immediately unplug the equipment and contact your dealer or a Seiko Epson service center for advice. Never attempt to repair this product yourself. Improper repair work can be dangerous.

  • Page 4: Caution Labels

    4 TM-L90 User’s Manual...
  • Page 5 Cover Operation Label If you use the cover operation label included in the package, attach it in one of the following locations: a) Side of the operation panel b) Beside the power switch c) Side of the printer TM-L90 User’s Manual 5...

  • Page 6: Downloading Drivers, Utilities, And Manuals

    FEED peeler. It also flashes when the printer is in a wait status for the button to be pressed. FEED button Feeds the roll paper. 6 TM-L90 User’s Manual...

  • Page 7: Power Switch Cover

    Power switch cover WARNING: If an accident occurs with the power switch cover attached, unplug the power cord immediately. Continued use may cause fire or shock. CAUTION: Do not remove the power switch soft cover. TM-L90 User’s Manual 7...

  • Page 8: Installing The Printer

    To hang the printer on the wall, see the Wall Hanging Bracket Set Installation Manual provided with the WH-10 for instructions. WARNING: When hanging the printer on the wall with the hanging bracket set, be sure to attach a connector cover to the printer. 8 TM-L90 User’s Manual...

  • Page 9: Changing The Paper Width

    Insert the roll paper spacer so that the front edge goes through the notch; then push down the spacer so that the hook on the spacer and the shaft align. Notch Front edge Roll paper spacer TM-L90 User’s Manual 9...
  • Page 10 60 mm with the spacer with the tabs broken off.) Tighten the spacer with the screw included with the spacer. (Although there are two holes, this is the only one to put the screw in.) Hole for screw 10 TM-L90 User’s Manual...

  • Page 11: Connecting The Cables

    Break off by hand any of the three portions indicated by circles in illustration to pass the cables through. Connect the cables to the printer. Attach the cover while passing the cables through the holes. TM-L90 User’s Manual 11...

  • Page 12: Installing The Roll Paper

    If you open them in the reverse order, the roll paper can get trapped under the roll paper cover when it is closed, causing a possible paper jam Peeler open lever Pull the roll paper cover open lever forward, and open the roll paper cover. Cover open lever 12 TM-L90 User’s Manual...
  • Page 13 (after the issued label is removed, the printer issues the next label). Make sure that the mode switch is set to the mode you are going to use. :Label continuous issuing mode :Label peeler issuing mode TM-L90 User’s Manual 13...
  • Page 14 Eliminate any slack in the roll paper, and then close the roll paper cover. Make sure to close it firmly, pressing both ends. After the paper is automatically fed and the first label comes out, the PAPER OUT LED starts flashing. 14 TM-L90 User’s Manual...
  • Page 15 Do not block the label peeler detector with your fingers, or anything else while the label issuing is in progress. This may cause the printer to feed the following label. CAUTION: When installing roll paper, be careful not to injure your hands on the manual cutter. TM-L90 User’s Manual 15...

  • Page 16: Cleaning The Thermal Head

    Do not damage the thermal head by touching it with your fingers or any hard object. Epson recommends cleaning the thermal head periodically (generally every 6 months) to maintain receipt print quality. Turn off the printer, open the peeler cover, and then the roll paper cover.

  • Page 17: Cleaning The Platen Roller/Roll Paper End Sensor

    Clean the platen roller and roll paper end sensor with a cotton swab lightly moistened with water or an alcohol. Platen roller Roll paper end sensor Close the roll paper cover after the water or alcohol has dried. TM-L90 User’s Manual 17...

  • Page 18: Cleaning The Peeler Unit

    (every 100,000 labels). You can clean them easily if you use a wasted label. Note: Do not use any alcohol based solvents for cleaning. Such solvents may enter the roller shaft and cause a malfunction of the peeler. 18 TM-L90 User’s Manual...

  • Page 19: Troubleshooting

    Turn off the power, open the peeler cover, and then open the roll paper cover to check for a paper jam. If there is a paper jam, remove the jammed paper and follow the instructions in the Installing Roll Paper section to prepare the printer for printing. TM-L90 User’s Manual 19...
  • Page 20 25.4 mm (dots per inch) *: Be sure to use a safety-standards-applied power source that meets the following specifications. Rated output: 24 V/2.0 - 10.0 A or more, Maximum output: 240 VA or less 20 TM-L90 User’s Manual...

Table of Contents