Table of Contents
Advertisement
Quick Links
How to connect an Epson wireless POS printer
Home
Sale Specials
How to connect an Epson TM Series Printer with a Wireless Adapter
Printers
TM-
Overview
U220
Installing Adapter
Network Setup
TM-
U200
Checking Adapter Settings
Configuring Router
TM-
Configuring Computer
U295
Configuring Adapter
Installing Driver
TM-
Troubleshooting
U375
TM-
T88III
Overview
TM-
Wireless connection allows you to locate the printer anywhere where there's power - no need to worry about printer
U88IV
cables.
TM-
A wireless printer replaces the traditional data cable with wireless adapters on the computer and printer, linked with a
T88V
radio signal. Once a wireless connection is established it offers a way to print documents without a direct connection.
TM-
U675
Required Components
TM-
U590
TM-
H6000
Power
Supplies
Interface
Cards
Cables
Ribbons
Paper
Installing and Setting the Connect-It Wireless Adapter
Install the Connect-It wireless adapter into the Epson TM series printer
http://www.beaglehardware.com/howtowireless.html[3/4/2011 12:28:11 PM]
Printers
Accessories
Epson POS Printer with Connect-It wireless adapter (UB-
R02, UB-R03 or equivalent)
Windows computer with wireless adapter or wireless
router
Service
Support
About Us
Epson Printers Covered
TM-T88III
TM-T88IV
TM-T88V
TM-U220
TM-U230
TM-U590
TM-U675
TM-H6000III
Contact
Catalog
Advertisement
Table of Contents
Related Manuals for Epson TM Series
Summary of Contents for Epson TM Series
- Page 1 How to connect an Epson wireless POS printer Home Sale Specials Printers Accessories Service Support About Us Contact Catalog How to connect an Epson TM Series Printer with a Wireless Adapter Printers Overview U220 Installing Adapter Network Setup U200 Checking Adapter Settings Configuring Router Configuring Computer...
-
Page 2: Network Setup
Epson PS-180). If changing a printer to wireless you must change the specific dip switch on the Epson printer to allow for the wireless card. (Key: DIP SW2-8 On: refers to the switch number 8, on switch bank 2, is turned On) Network Setup The wireless adapter can be "connected"... - Page 3 How to connect an Epson wireless POS printer Getting Initial Printer and Wireless Adapter Settings Get the initial settings of the wireless adapter. Run the printer self test (hold down the feed button while turning on the printer). The printer will print a list of initial settings including SSID (network ID), Mode (Ad-Hoc or Infrastructure), current IP address (default: 192.168.192.168)
- Page 4 How to connect an Epson wireless POS printer A sheet will print showing the MAC address, SSID, mode, wireless channel number, authorization method (None, WEP), Gateway (GW), IP address and IP assignment method. The network specific settings have been highlighted above.
- Page 5 How to connect an Epson wireless POS printer Manual setting IP addresses are assigned on your network. Use WEP None None / 64-bit / 128-bit WEP Key None set this if key is used Channels 1-11. When using Ad-Hoc mode, Channel the channel directly.
- Page 6 How to connect an Epson wireless POS printer your IP Address are not 192.168.192, (Ex. 192.168.1), then you need to change your computer's IP address to an address in the same subnet. Change the IP address to a static IP address. Then make the IP address of the adapter different than the wireless adapter (like 192.168.192.2).
- Page 7 How to connect an Epson wireless POS printer If you are using a wireless router then you should verify that the printer is connected to the router. Turn the printer on Log onto the router administration from a computer on the network.
-
Page 8: Installing The Printer Driver In Windows
How to connect an Epson wireless POS printer less than 10 minutes). This is a process controlled by Epson not Beagle Hardware. TECHNICAL RESOURCES 5. Click on WIRELESS INTERFACES CONNECT-IT INTERFACES 6. Select under the download icon for the TMNetWinConfig 7. - Page 9 How to connect an Epson wireless POS printer Configuring the Printer in Windows You need to make a few changes in the printer settings to get it to work with the wireless adapter. Specifically you need to configure the port you are using. Open the printer in the Windows Printer Folder. Select the Ports Tab. Turn off bidirectional support, if enabled.
-
Page 10: Testing The Printer
IP address. The Epson printer driver has not been installed for the wireless adapter and printer in use. The network mode is not correct. If the computer is in the AdHoc mode, the wireless adapter must be in the AdHoc mode. -
Page 11: Wireless Problems
How to connect an Epson wireless POS printer WEP key setting is not correct. If setting is not possible, initialize the wireless adapter. Install the wireless adapter in the TM printer, turn the power on, and press the Mode button of the wireless adapter for more than three seconds to re-initialize the wireless adapter. - Page 12 How to connect an Epson wireless POS printer E-Mail: info@beaglehardware.com 800-253-6407 Call: Copyright© 2011 Beagle Hardware http://www.beaglehardware.com/howtowireless.html[3/4/2011 12:28:11 PM]...