Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Art-Tech Diamond 1800
Summary of Contents for Art-Tech Diamond 1800
- Page 1 Remote control radio glider Remote control radio glider USER S MANUAL...
-
Page 2: Table Of Contents
Contents Technical Parameter Features Warning Please read the following instructions and fully understand it Main parts of the airplane Flying adjustment Tips for flying Charge mode and warning Safety instructions for Li-poly batteries Caution Assembly Troubleshooting Valuable experience Operating Manual for the radio control system Transmitter particular introduce The process of frequency bind for 2.4GHz R/C system Normal flight... -
Page 3: Technical Parameter
ENGLISH PARTS Please read this manual carefully and follow the instruction. Thank you for choosing this classical model airplane of Art-Tech. This model is generally for intermediate and experienced hobby enthusiast. It includes the following accessories: 2.4G transmitter, ESC, motor, battery, servo, etc, which will bring much fun for the manipulator. -
Page 4: Please Read The Following Instructions And Fully Understand It
Please read the following instructions and fully understand it. 1) This diamond model is not suitable to fly in the below list place: the crowd, the place with telegraph pole, automobiles, place near the road and aerodrome, you need enough space to control the plane. Please consider the safety for other people and yourself. -
Page 5: Flying Adjustment
Flying adjustment 1) The Diamond glider will have a better perform after fully charged. 2) Beeline flying: Please adjust the inching switch in the transmitter if you find it is a little difficult to fly straightly. For example, when you find the Diamond glider flies to the left by aberrancy, please turn the inching switch to the right in the transmitter. -
Page 6: Safety Instructions For Li-Poly Batteries
Notice 1. Do not insert any conductive into the cooling hole when power is on, or damage will be caused to the charger. 2. While charging is in process, please do not place it near flammable materials. 3. Expect Li poly battery, this charger is not allowed for other kinds of battery. 4. -
Page 7: Assembly
Assembly Take off the left/right wing, and the Insert the aluminum pipe into the steel avigation aluminum pipe. tube of the left or right wing, and make sure the center position of the aluminum pipe is in the joint of the two wings. Connect the servo cable at the end of I n s e r t t h e l e f t / r i g h t w i n g i n t o t h e the left/right wing (please don’t make it... - Page 8 Assembly Turn on the transmitter and push the 10. Take off the nose cowl and fix the throttle joystick in the lowest position. battery, and then turn on the battery power. 11. Check the servo and the motor. Make 12. Put the nose cowl back, now the glider is sure the control surface moves in the right ready to fly direction, and the rudder/elevator and...
-
Page 9: Troubleshooting
Troubleshooting Problem Cause Solution 1. Battery is not fully charged. 1. Charge the batteries. 2. The battery of transmitter is not sufficient 2. Install a full charged battery Motor does not run 3. Contact the local dealer 3. Check the wire connection inside the model The servo cable didn’t plug 1. -
Page 10: Operating Manual For The Radio Control System
Notes If the parts of the Diamond Glider were damaged, please contact the dealer to purchase new components. Operating Manual for the radio control system Components to the R/C system a transmitter, a receiver, a servo, a speed controller The sketch map for connecting the receiver: RECEIVER ER61-2.4GHz Signal... -
Page 11: Transmitter Particular Introduce
Transmitter particular introduce Mode 1 Antenna Carrying bar Hook Elevator down Throttle Max Rudder Aileron Aileron Rudder right left right left Elevator up Throttle Min Trim CH2 Trim CH3 Trim CH1 Trim CH4 Power indicator Power switch Charger port Frequency Switch Reverse switch on rud der Reverse switch on thrott le Reverse switch on elevator... -
Page 12: The Process Of Frequency Bind For 2.4Ghz R/C System
The process of frequency bind for DSSS series 2.4GHz R/C system Especial notice: The process of frequency binding for this radio, please follow the instruction of this page. 1. Press the switch for frequency bind, then turn on the transmitter's power. Plug the short-circuit plug into the 3. -
Page 13: Normal Flight
Normal flight Left stick Speed up pushing up Left stick Speed down pulling down Left stick Nose turn left moving left Left stick Nose turn right moving right Right stick nose turn down/ pushing up move forward Right stick Nose turn up/ pulling down move forward Right stick... -
Page 14: Inspection And Adjustment Before Flying
Inspection and adjustment before flying 1. Switch for power supply: Install 8 cells dry batteries in the transmitter according to the symbol of battery’s polarity, then turn on the switch of power. Install the full charged battery into the foreside of the fuselage, and connect the plug of battery with the electronic Speed Controller. -
Page 15: Spare Parts List
4. If the motor runs slowly or the thrust is not powerful, please do not take it off. Check if the battery has been fully charged, and if there is any problems with the motor or ESC. The power system can be adjusted during flying to save power and lengthen the flying time, and the recommended method is flying---gliding—flying.