Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Operator's Manual
Advertisement
Table of Contents
Related Manuals for Rikon Power Tools 30-120
Summary of Contents for Rikon Power Tools 30-120
- Page 1 13” Bench Drill Press Model: 30-120 Record the serial number and date of purchase in your manual for future reference. Serial number: Date of purchase: For more information: www.rikontools.com info@rikontools.com For Parts or Questions: techsupport@rikontools.com 877-884-5167 Part # 30-120M1...
-
Page 2: Safety Warnings
Operator Safety: Required Reading IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following instructions must be followed at all times. There are certain applications for which this tool was designed. We strongly recommend that this tool not be modified and/ or used for any other application other than that for which it was designed. -
Page 3: Drill Press Safety Rules
ALWAYS DISCONNECT TOOLS. Disconnect tools before servicing and when changing accessories such as blades, bits, and cutters. ALWAYS AVOID ACCIDENTAL STARTING. Make sure switch is in “OFF” position before plugging in cord. NEVER LEAVE TOOLS RUNNING UNATTENDED. ALWAYS CHECK FOR DAMAGED PARTS. Before initial or continual use of the tool, a guard or other part that is damaged should be checked to assure that it will operate properly and perform its intended function. -
Page 4: Table Of Contents
Table of Contents Safety Warnings..........................2-3 Drill Press Safety Rules ..........................3 Specifications ............................4 Contents of Package........................5 Unpacking and Cleaning the Drill Press....................5 Getting To Know Your Drill Press......................6 Assembly ..............................7 Base and Column Assembly........................7 Head Assembly..........................7-8 Installing/Removing the Chuck and Arbor..................9-10 Installing the Table..........................10 Adjustment and Operation........................11 Head Adjustments .........................11... -
Page 5: Contents Of Package
Contents of Package Model 30-120 13” Bench Drill Press is shipped complete in one box. TABLE OF LOOSE PARTS 1. Unpacking and Checking Contents a. Separate all “loose parts” from packaging Item Part Name materials and check each item with “Table of Drill Press Head Loose Parts”... -
Page 6: Getting To Know Your Drill Press
Getting to Know Your Drill Press Belt Cover Motor Switch Feed Handle Lock Handle Belt tension Handle Chuck Table Lock Handle Lock Handle Table support Column Column Support Base... -
Page 7: Assembly
Assembly Base and Column Assembly 1. Place the base (A-Fig. 1) on a level floor where the machine will be used. 2. Attach the column (B-Fig.1) to the base (A-Fig. 1) using four M8x20 hex bolts. Tighten all four bolts. 3. -
Page 8: Head Assembly
Head Assembly 2. Align the drill press head (A-Fig. 6) with the base of the drill press (B-Fig. 6). Figure 6 3. Tighten the drill press head (A-Fig. 7) to the column (B-Fig. 7) by tightening the two set screws on the right side of the head as shown. Figure 7 4. -
Page 9: Installing/Removing The Chuck And Arbor
INSTALLING/REMOVING CHUCK AND ARBOR Open Chuck Jaws It is important that the chuck IMPORTANT! and arbor are free of any grease or rust protection. Use ordinary household grease remover. INSTALLING THE CHUCK AND ARBOR 1. Open the chuck jaws as wide as possible to prevent any damage. -
Page 10: Installing The Table
REMOVING THE CHUCK 1. Open the chuck jaws as wide as possible to prevent damage. 2. Lower the spindle until the slot in the spindle is exposed. (Fig. 14) 3. Position the table approximately 1/2” below the extended chuck. Figure 14 4. -
Page 11: Adjustment And Operation
TABLE ADJUSTMENTS Raising and Lowering the Table 1. Loosen the column lock (A-Fig. 19) on the table support bracket (B-Fig. 19). 2. Turn the crank to raise or lower the table to the desired height. 3. Tighten the column lock (A-Fig. 19). Figure 19 The table can rotate 360 by loosening the table... -
Page 12: Setting The Spindle Lock
CHANGING SPINDLE SPEEDS CONT. 6. Place the belt on the pulleys in relation to the speed chosen on the speed selection chart starting with the motor pulley first. (Fig. 23) 7. Push the belt tension handle backward on the motor until there is approximately 1/2" deflection in the belt. -
Page 13: Maintenance
Maintenance WARNING: To avoid injury due to unexpected starting, before cleaning or carrying out maintenance work, switch off and disconnect the drill press from the power source. 1. Never use water or other liquids to clean the drill press. Use a dry brush. 2. -
Page 14: Electrical Requirements
Eletrical Requirements In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances. -
Page 15: Troubleshooting
Trouble Shooting... -
Page 16: Parts Explosion
Parts Explosion... -
Page 17: Parts List
Parts List Description Part No. Description Part No. Pivot-Idler 1-M6X10GB80B Screw-Hex Soc Set M6 1-1705007 Pulley-Center 1-1501011 Collar-Rack 1-1505006-02001G Bearing-Ball 15mm 1-1501006 Gear-Helical 1-BRG80202GB278 Knob-Motor Adjusting 1-1501009-10001G Crank 1-1502005 Screw-Socket Set M10 1-1301014-02001G Table 1-M6X8GB80B Handle-Belt Tension 1-1501013-01001S Clamp-Table 1-1502004 Pin-Stop 1-M16X35GB5781B Screw-Hex Head M16x20-35... -
Page 18: Notes
Notes... -
Page 19: Warranty
Warranty 2-Year Limited Warranty RIKON Power Tools/Richen Enterprise, Inc. (“Seller”) warrants to only the original retail consumer/purchaser of our products that each product be free from defects in materials and workmanship for a period of two (2) years from the date the product was purchased at retail. This warranty may not be transferred. - Page 20 For more information: 110 Cummings Park Woburn, MA 01801 877-884-5167/781-933-8400 info@rikontools.com www.rikontools.com Copyright Richen Enterprise, Inc. 2006 Printed in China 6/06...