Table of Contents
Advertisement
Quick Links
34-260
Benchtop Mortising Machine
with X-Y Moving Table
CU72141729.01
CU72141730.01
Operator's Manual
Record the serial number and date of purchase in your manual for future reference.
Serial Number: _________________________
Date of purchase: _________________________
For technical support or parts questions, email techsupport@rikontools.com or call toll free at (877)884-5167
www.rikontools.com
34-260M2
Advertisement
Table of Contents
Related Manuals for Rikon Power Tools 34-260
Summary of Contents for Rikon Power Tools 34-260
- Page 1 34-260 Benchtop Mortising Machine with X-Y Moving Table CU72141729.01 CU72141730.01 Operator’s Manual Record the serial number and date of purchase in your manual for future reference. Serial Number: _________________________ Date of purchase: _________________________ For technical support or parts questions, email techsupport@rikontools.com or call toll free at (877)884-5167 www.rikontools.com...
-
Page 2: Table Of Contents
Changes and improvements may be made at any time, with no obligation on the part of Rikon Power Tools, Inc. to modify previously delivered units. Reasonable care has been taken to ensure that the information in this manual is correct, to provide you with the guidelines for the proper safety,... -
Page 3: Safety Instructions
SAFETY INSTRUCTIONS IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following instructions must be followed at all times. Failure to follow all instructions listed below may result in electric shock, fi re, and/or serious personal injury. There are certain applications for which this tool was designed. - Page 4 SAFETY INSTRUCTIONS 12. KEEP PROTECTIVE GUARDS IN PLACE AND IN 25. ALWAYS WEAR A DUST MASK TO PREVENT WORKING ORDER. INHALING DANGEROUS DUST OR AIRBORNE PARTICLES, including wood dust, crystalline silica dust 13. AVOID ACCIDENTAL STARTING. Make sure that and asbestos dust. Direct particles away from face and the power switch is in the “OFF”...
-
Page 5: Electricals & Wiring Diagram
SAFETY INSTRUCTIONS EXTENSION CORDS ELECTRICAL SAFETY THE USE OF AN EXTENSION CORD THIS TOOL MUST BE GROUNDED WITH THIS MACHINE IS NOT RECOMMENDED. For WHILE IN USE TO PROTECT THE OPERATOR FROM best power and safety, plug the machine directly into a ELECTRIC SHOCK. - Page 6 SAFETY INSTRUCTIONS SPECIFIC SAFETY INSTRUCTIONS FOR BENCHTOP MORTISING MACHINES This machine is intended for the drilling of square mortise holes in hard or softwoods. Any other use not as specified, including modification of the machine or use of parts not tested and approved by the equipment manufacturer, can cause unforeseen damage to the machine or operator.
-
Page 7: Getting To Know Your Machine
Chuck Housing & Access Covers CONTENTS OF PACKAGE Model 34-260 Benchtop Mortising Machine is shipped complete in one box. Unpacking and Clean-up 1. Carefully remove all contents from the shipping carton. Compare the contents with the list of contents to make sure that all of the items are accounted for, before discarding any packing material. -
Page 8: Assembly
CONTENTS OF PACKAGE 34-260 Benchtop Mortising Machine with X-Y Moving Table CU72141729.01 CU72141730.01 Operator’s Manual Record the serial number and date of purchase in your manual for future reference. Serial Number: _________________________ Date of purchase: _________________________ For technical support or parts questions, email techsupport@rikontools.com or call toll free at (877)884-5167 www.rikontools.com... - Page 9 ASSEMBLY NOTE: Before assembly begins, make sure that the Mortiser is positioned on a sturdy work sur- face, and secured down to prevent any tipping. LOCKING Release the Mortising Head Assembly. SCREW The Mortiser’s head assembly is secured in the ‘down’...
- Page 10 Screws with Washers (#18). FIG. 7. Installing the Mortising Chisel and Drill Bit The 34-260 Mortiser uses 1”, 3/4” or 5/8” FIG. 7 diameter shank chisels with a 3” cutting depth. 1. Open the chuck access Cover (#14)(A) and loosen the side bushing set Screw (#86)(B).
- Page 11 ASSEMBLY 3. Open the chuck jaws to allow the drill bit to THE MACHINE MUST NOT BE inserted into the chuck, and then insert the PLUGGED IN AND THE POWER SWITCH MUST BE IN THE OFF POSITION UNTIL ALL ADJUSTMENTS ARE COMPLETE. chisel into in the mortiser’s head, or head with a bushing installed.
-
Page 12: Adjustments
ADJUSTMENTS Adjusting the Work Table The top Table (#42) that holds your work piece, adjusts forward and backwards on dovetail ways, FIG. 12, A. The table movement is controlled by the small knurled Knob (#38) (B). 1. To tighten or loosen the movement of the table, pressure on the dovetails can be adjusted with the 2 Screws and Nuts (# 54, 53). - Page 13 ADJUSTMENTS Continued from page 12 The front Clamp Plate (#43) will rotate slightly to give pressure on irregular shaped pieces, and the Clamping Base (#37) can be angled to conform to tapered work pieces. The two Bolts (#32) can be loosened and tightened to secure the fence in position for maximum holding power.
-
Page 14: Operation
OPERATION Before turning on the machine, review the safety precautions listed on pages 3 to 6. Make sure that you fully understand the features, adjustments and capabilities of the machine that are outlined throughout this manual. Tips on usage can be found in books, magazines, researching the internet and other resources. -
Page 15: Troubleshooting
TROUBLESHOOTING PROBLEM REMEDY PROBABLE CAUSE 1. Machine is not plugged in. Motor will not start. 1. Plug power cord in electrical outlet. Fuses or circuit break- 2. Fuse or circuit breaker are open. 2. Replace fuse or circuit breaker. 3. Power switch or cord is faulty. ers trip or blow. -
Page 16: Parts Diagram
PARTS DIAGRAM NOTE: Please reference the Manufacturer’s Part Number when calling for Replacement Parts. For Parts under Warranty, the Serial Number of your machine is required. -
Page 17: Parts List
PARTS LIST RIKON RIKON DESCRIPTION PART NO. DESCRIPTION PART NO. Operating Lever Handle P34-260-1 Spring Washer P34-260-46 Motor P34-260-2 Screw P34-260-47 Switch Box P34-260-3 P34-260-48 Handle Screw Handle Screw P34-260-4 P34-260-49 Handle Shaft P34-260-5 Screw P34-260-50 Rack P34-260-6 P34-260-51 Sliding Plate Screw P34-260-7 P34-260-52... -
Page 18: Accessories
ACCESSORIES MORTISING CHISELS AND BITS Machined steel chisels have 5/8” shanks. Drill bits have brad points, single cutting edge and up-spiral flutes for rapid chip removal. Both chisel and bits require final sharpening before use. 29-914 1/4” Mortising Chisel & Bit 29-915 5/16”... -
Page 19: Warranty
WARRANTY... - Page 20 34-260 For more information: 16 Progress Road Billerica, MA 01821 877-884-5167 / 978-528-5380 techsupport@rikontools.com www.rikontools.com 34-260M2...