Advertisement
GENERAL INFORMATION AND MAlNTENANdE l-19
792UQ4
Fig. 69 Accessory V-belt routing-Mii
subishf 1.6L, 1.6L,-1.6L, 2.OL and 2.4L en
gines
33151PM
Fig. 70 After the adjusting and fixed bolt!
are loosened, rotate the pump . . .
/ F$71t immtl$mm&a
the power :::
6. Rotate the pump until the proper tension is
reached.
7. Tighten the adjusting bolts on the pump.
8. Tighten the fixed bolt on the rear of the bracket.
9. Install the alternator belt.
A/r: COMPRESSOIl BEL f
1. Loosen the tension oullev and remove the belt.
2. The installation is the reverse of the removal.
.3.gL DGHC, 3.OL SOHC (Gaiant models
only) and 3.5L Engines
4. Remove the belt.
To install:
5. Install the belt on the crankshaft and alternator
pulleys.
6. Using the adjusting bolt on the tensioner,
tighten the belt to the desired tension.
7. Tighten the fixing nut to hold the adjustment.
8. Install the undercover and lower the vehicle to
_,
the tloor.
9. Connect the negative battery cable.
POWER SliEERlNG BEL f
6 See Figures 72 and 73
1. Disconnect the neaative batteN cah+P
-I
Wait at least 60 seconds after the negative
battery cable is disconnected to prevent poS-
sibie deployment of the air bag.
2. Raise and safely support the vehicle and re-
mob re the undercover.
3. Remove the alternator and NC compressor
belt.
4. Lower the vehicle and remove the cruise con-
trol oumn link iW%mblV.
79244Q.37
--
I--
r
----
-
_I
Fig. 72 Serpentine belt routing-Mitsubishi
5. Place the power steering hose under the oil
reservoir.
3.OL engines (except 1696-00 Galant mod-
6. Loosen the tension pulley fixing bolts and re-
els)
Generator
pulP
1
move the power steering pump drive belt.
To install:
1
7. install the Dower steerina oumu r+r+v~ hp++
8. Insert an extension bar &eoufvaik;;t"f;;id'he
opening at the end of the tension pulley bracket and
pivot the pulley to apply tension to the belt.
9. Tighten the fixing bolts.
10. Raise the vehicle and install the alternator and
compressor belt.
Il. Install the undercover and lower +hfi vph+r+p
.I,., .VII.".Y.
12. Connect the negative battery cable.
I
3.OL SGHC (Diamante Models Onivl Enotne
I
,r
"
1. Disconnect the negative battery cable.
2.' Loosen the lockbolt on the face nf the A/C
_ __.-
tensioner pulley.
3 Turn the adiustina bolt of the A/C +fincrnner
pulley to loosen the tension of the A/C belt.
4. Remove the A/C compressor belt.
5. Loosen the locknut on the face of the power
to loosen the tc
7. Remov
Fig. 73 Accessory V-belt routing-Mitsubishi
3.5L and 1996-00 3.OL SOHC Galant en-
gines
steering/alternator
tensloner pulley.
6. Turn the adjusting bolt of the tensioner pulley
msion of the belt.
'e the power steering/alternator
belt.
To install:
8. Install the power steering/alternator
belt first
.* .* . ,^
ssor drive belt.
ana tnen tne A/ti compre:
9. Adjust the belts t+
ing the adjusting bolts anu
II~IIWII
pueey tlxmg
I the proper tension by turn-
A.:-L I-..-.. I,^, .'
nut/bolt.
10. Tighten the mounting nut of the power steer-
ing/alternator tensioner pulley to 36 ft. Ibs. (50 Nm).
Wait at least 60 seconds after the negative
battery cable is disconnected to prevent pos-
sible deployment of the air bag.
-The manufacturer does not provide a
torque specification for the bolt that secures
A/C tensioner pulley.
2. Raise and safely support the vehicle and re-
11. Connect the negative battery cable.
move the front undercover.
3. Loosen the tension pulley fixing nut and relieve
the tension on the belt by turning the adjusting bolt.
Advertisement
