Kyosho MAD FORCE Instruction Manual page 34

ƒV ƒt ƒgƒ^ƒC ƒ~ƒ" ƒO ‚Ì '² •®
3ƒX ƒs•[ ƒhƒ~ƒbƒV ƒ‡ƒ" ‚Ì ƒV ƒt ƒgƒ^ƒC ƒ~ƒ" ƒO ‚Í •o ‰× Ž ž‚É "K•³ ˆÊ'u ‚É '² •®•Ï ‚Å ‚· ‚ª •AƒV ƒt ƒgƒ^ƒC ƒ~ƒ" ƒO ‚Ì •Ï •X‚Í ‰º ‹ L ‚Ì —l ‚ É •s ‚È ‚Á ‚Ä ‚- ‚¾‚³ ‚¢ •B
The shift timing of the 3-speed transmission is set at the factory. If you wish to change the settings, adjust as shown in the following illustrations.
ƒV ƒt ƒgƒ^ƒC ƒ~ƒ" ƒO ‚Ì '² •®Žž‚Í •AˆÀ'S ‚Ì ‚½‚ß •K‚¸ ƒG ƒ" ƒW ƒ" ‚ð Ž~‚ß ‚Ä •s ‚È ‚Á ‚Ä ‚- ‚¾‚³ ‚¢ •B
For reasons of safety, do not perform adjustments while the engine is running!
ƒV ƒt ƒgƒ^ƒC ƒ~ƒ" ƒO ‚Ì '² •®‚Ì 'O‚É •AƒG ƒ" ƒW ƒ" ‚Ì '² •®‚ð •[ •ª ‚É •s ‚È ‚Á ‚Ä ‚- ‚¾‚³ ‚¢ •B
Adjust the engine before adjusting the gear shift timing.
< 2'¬ –Ú ‚Ì '² •® >
< Adjustment for second gear.
1
4x4mm
ƒt ƒ• ƒ" ƒg
42
Front
< 3'¬ –Ú ‚Ì '² •® >
< Adjustment for third gear.
ƒt ƒ• ƒ" ƒg
Front
ƒV ƒt ƒgƒ^ƒC ƒ~ƒ" ƒO ƒV ƒt ƒgƒ^ƒC ƒ~ƒ" ƒO
‚ª '• ‚- ‚È ‚é •B ‚ª 'x ‚- ‚È ‚é •B
Shift timing Shift timing
becomes quicker. becomes slower.
24
3ƒX ƒs•[ ƒhƒgƒ‰ ƒ" ƒX ƒ~ƒbƒV ƒ‡ƒ" ‚Í •A•‚ '¬ ‚Å ‰ñ " ] ‚· ‚é ‚½‚ß ‰º ‹ L ‚Ì "_ ‚É '• ˆÓ‚µ ‚Ä ƒ• ƒ" ƒeƒi ƒ" ƒX ‚ð •s ‚Á ‚Ä ‚- ‚¾‚³ ‚¢ •B
•œ Še ‰ñ " ] •" ‚Ì ƒxƒA ƒŠ ƒ" ƒO ‚È ‚Ç‚Í •AƒX ƒ€ •[ ƒY ‚É ‰ñ " ] ‚· ‚é ‚æ‚¤ ‚É '• –û‚ð ‚µ ‚Ä ‚- ‚¾‚³ ‚¢ •B
•œ ƒV ƒƒƒV •[ ‚É ƒr ƒX ‚Ì ‚ä ‚é ‚Ý ‚ª ‚È ‚¢ ‚©'è Šú "I ‚É "_ ŒŸ ‚ µ •A'• ‚µ '÷ ‚ß ‚µ ‚Ä ‚- ‚¾‚³ ‚¢ •B
•œ ƒ• ƒ" ƒE ƒG ƒC ƒxƒA ƒŠ ƒ" ƒO ‚ª ƒ• ƒbƒN •ûŒü ‚ Å ƒ• ƒbƒN ‚· ‚é ‚©'è Šú "I ‚É "_ ŒŸ ‚ µ •Aƒ• ƒbƒN ‚µ ‚È ‚¢ •ê •‡ ‚Í •AƒV ƒƒƒt ƒg‹y ‚Ñ•Aƒ• ƒ" ƒE ƒG ƒC ƒxƒA ƒŠ ƒ" ƒO ‚ð Œð Š ·‚µ ‚Ä ‚- ‚¾‚³ ‚¢ •B
•œ ƒM ƒ„ ‚Ì ‚² ‚Ý ‚â •¬ •Î ‚Í •A"j '¹ ‚Ì Œ´ ˆ ö ‚É ‚È ‚é ‚Ì ‚Å •í ‚É ‚« ‚ê ‚¢ ‚É ‚µ ‚Ä ‚¨ ‚« ‚Ü‚µ ‚å ‚¤ •B
Note the following in order to ensure smooth operation and long life of the 3-Speed Transmission.
Lubricate the ball bearings to ensure smooth operation.
Regularly check whether the screws on the chassis are firmly tightened, and retighten if necessary.
Regularly check whether the oneway bearing locks into the direction indicated. If it does not lock, replace the shaft or oneway bearing.
Keep the gears clean from dirt and sand to prevent damage.
34
ADJUSTMENT OF THE GEAR SHIFT TIMING
>
2
3
24
4x4mm ƒ• ƒbƒN ƒZƒbƒgƒrƒX
Lock Set Screw
40 39 33
>
2
3
24
4x4mm ƒ• ƒbƒN ƒZƒbƒgƒrƒX
Lock Set Screw
1
2
35 38 36
24
ƒZƒbƒgƒr ƒX ‚Í 2mm‚Ì ˜ZŠp ƒŒ ƒ" ƒ` ‚Å '² •®‚µ •A'÷ ‚ ß •i ŽžŒv • ûŒü • j ‚ê ‚Î ƒV ƒt ƒgƒ^ƒC ƒ~ƒ" ƒO ‚ª
'x ‚- •A‚ä ‚é ‚ ß •i "½ŽžŒv • ûŒü • j ‚ê ‚Î '• ‚- ‚È ‚è ‚Ü‚· •B
Adjust the set screw
clockwise. For faster shift timing, unscrew (counterclockwise).
ˆê ‰ñ ‚ Ì '² •®—Ê ‚ Í –ñ10• ‹ ‚ª –Ú ˆÀ‚Å ‚· •B
Ten degrees is sufficient for each adjustment.
2'¬ –Ú ‚Æ 3'¬ –Ú ‚Ì ƒ^ƒC ƒ~ƒ" ƒO ‚ª ‚í ‚©‚ç ‚È ‚- ‚È ‚Á ‚Ä ‚µ ‚Ü‚Á ‚½Žž‚É ‚Í •A‚Ü‚¸ 3'¬ –Ú ‚Ì ƒZƒbƒgƒr
ƒX ‚ð ‚¢ ‚Á ‚Ï ‚¢ ‚Ü‚Å '÷ ‚ß •ž ‚Ý •A3'¬ –Ú ‚ª ƒV ƒt ƒgƒA ƒbƒv‚µ ‚È ‚¢ •ó 'Ô‚Å 2'¬ –Ú ‚ð '² •®‚µ •A‚» ‚ê ‚©
‚ç 3'¬ –Ú ‚Ì ƒZƒbƒgƒr ƒX ‚𠕘 •X‚É ‚ä ‚é ‚ß ‚Ä •AƒV ƒt ƒgƒ| ƒC ƒ" ƒg‚ð 'T ‚µ ‚Ü‚· •B
If you confused second and third gear shifting, tighten the third gear set screw firmly to
avoid shifting up. Adjust the second gear first, and then unscrew the third gear set screw
to find the correct shift timing.
ƒ• ƒ" ƒeƒi ƒ" ƒX
1 42
11TƒX ƒvƒ• ƒP ƒbƒg‚Ì 4x4mmƒZƒbƒgƒr ƒX ‚ð ‚ä ‚é ‚ß ‚Ü‚· •B
Unscrew the 4x4mm setscrew from the 11T sprocket
2 40
1'¬ ƒX ƒp•[ ‚Æ
Slide the first
3 33
2'¬ —p ƒ N ƒ‰ ƒbƒ` ƒ{ ƒX ‚É •t ‚¢ ‚Ä ‚¢ ‚é
ƒV ƒt ƒgƒ^ƒC ƒ~ƒ" ƒO ‚ð '² •®‚µ ‚Ü‚· •B
Adjust the shift timing by installing a set screw
clutch boss for second gear
4 40 39
,
'÷ ‚ß ‚Ü‚· •B
Slide the
the 4x4mm set screw
ƒŠ ƒ„
Rear
1
4x4mmƒZƒbƒgƒr ƒX ‚ð ‚ä ‚é ‚ß ‚Ä •A
•û‚Ö‚¸ ‚ç ‚µ ‚Ü‚· •B
Unscrew the 4x4mm setscrew and slide back the 6mm
stopper
2
30
3ƒX ƒs•[ ƒhƒV ƒƒƒt ƒg‚ð 'O•û‚É ‰Ÿ ‚ µ ‚Ä •A
ŠO ‚ð 'O‚É ‚¸ ‚ç ‚µ ‚Ü‚· •B
4x4mm
Push forward the 3-speed shaft
forward except the third spur gear.
3
35
3'¬ —p ƒ N ƒ‰ ƒbƒ` ƒ{ ƒX ‚É •t ‚¢ ‚Ä ‚¢ ‚é
ƒV ƒt ƒgƒ^ƒC ƒ~ƒ" ƒO ‚ð '² •®‚µ ‚Ü‚· •B
Adjust the shift timing by installing a set screw
clutch boss for third gear
30
4
30
‚ð ‚à ‚Æ ‚É ‚à ‚Ç‚µ •A
ŒÅ ' è ‚µ ‚Ü‚· •B
ƒŠ ƒ„
Slide back the 3-speed shaft
Rear
stopper
24
using a 2mm hex wrench. For slower shift timing, screw
MAINTENANCE
39
2'¬ ƒX ƒp•[ ‚ð "¯ Žž‚É 'O•û‚Ö‚¸ ‚ç ‚µ ‚Ü‚· •B
40 39
and second spur gears forward.
24
33
.
42
‚ð ‚à ‚Æ ‚É ‚à ‚Ç‚µ •A ‚Ì 4x4mmƒZƒbƒgƒr ƒX ‚ð •Ä‚Ñ
40 39
and spur gears back, and then tighten
42
.
36
6mmƒX ƒgƒbƒp•[ ‚ð Œã
36
.
30
and slide all gears
24
35
.
36
6mmƒX ƒgƒbƒp•[ ‚ð ‚à ‚Æ ‚Ì ˆÊ'u ‚É
30
and secure the 6mm
36
at its original position.
42
.
‚Ì ƒZƒbƒgƒr ƒX ‚Å •A
24
on a
38
3'¬ ƒX ƒp•[ ˆÈ
‚Ì ƒZƒbƒgƒr ƒX ‚Å •A
24
on a