Sailor RT5022 VHF DSC Operation Manual page 58

Interfaces
VHF Signal
Options connector designation
15-pin D-sub male
VDR+
pin 1
pin 2 VDR-
pin 3 AUX2
pin 4 AUX2 NO
pin 5 AUX 1
pin 6 AUX 1 NO
pin 7 int_Speaker +
pin 8 int_Speaker -
pin 9 DSC CALL
pin 10 DSC CALL NO
pin 11 GND
pin 12 NMEA +
pin 13 NMEA -
pin 14 DSC ALARM
pin 15 DSC ALARM NO Purple/Wht
Housing
Note 1: Relay contact ratings (resistive load)
Note 2: Following NMEA sentences are supported: GLL, RMC, ZDA, GGA, VTG, GNS
in accordance with IEC61162-1
Sparc II Connections
VHF Signal Cable
SPARC connector designation p/n 56.114
15-pin D-sub female
12.5VDC+ Red/Wht
pin 1
Yel
pin 2 DATA_+
pin 3 DATA_- Yel/Wht
pin 4 TX_AF+ Blue/Wht
pin 5 TX_AF- Blue
pin 6 GND Orange + Red
pin 7 12.5VDC+ Orange/Wht
pin 8 RX_AF+ Green/Wht
pin 9 RX_AF- Green
pin 10 12.5VDC+ Blk/Wht
pin 11 EXT.Speaker + Brown
pin 12 EXT.Speaker - Brown/Wht
pin 13 GND Blk
pin 14 Lineout + Purple
pin 15 Lineout - Purple/Wht
Housing Screen
EXT LS
EXT LS
NOTE: In case of connecting CU1 and/or CU2 directly to Connection Box, i.e. not utilizing Extension Box for connecting each CU,
jumpers J1/J2 and/or J3/J4 in Connection Box must be removed in order to disconnect VHF Ext. Speaker (VHF LS) output from these terminals
and make available the CU Ext. Loudspeaker (CU LS) connections instead.
52
Cable Connection Connection
p/n 539603 box
5m In from VHF External conn.
Brown
X1-1
Brown/Wht X1-2
Orange X1-3
Orange/Wht X1-4
Blue X1-5
Blue/Wht X1-6
Green X1-7
Green/Wht X1-8
Red X1-9
Red/Wht X1-10
X1-11
Blk+Blk/Wht
Yel X1-12
Yel/Wht or Blk X1-13
Purple X1-14
X1-15
Screen Chassis Chassis
Max. switched power: 30W or 60VA
Max. switched current: 1.0A
Max. switched voltage: 150VDC or 125VAC
Connection box Connection box Connection box Connection box Alarm panel
In from VHF Out to CU1 or
5m extension box
X3-1 X4-1
X3-2 X4-2
X3-3 X4-3
X3-4 X4-4
X3-5 X4-5
X3-6 X4-6
X3-7 X4-7
X3-8 X4-8
X3-9 X4-9
X3-10 X4-10
X3-11 X4-11
X3-12 X4-12
X3-13 X4-13
X3-14 X4-14
X3-15 X4-15
Chassis Chassis
X8-1
X8-2
Signal description
box
Mixed Rx/Tx audio output for
X2-1
recording. Galvanically isolated,
X2-2 balanced signal, 0dBm into 600Ω
Relay contact closing on event pre-
X2-3
defined through service
X2-4 programming (see note 1)
Relay contact closing on event pre-
X2-5
defined through service
X2-6 programming (see note 1)
VHF internal speaker output,
X2-7
nom. 5W into 8Ω.
X2-8
Relay contact closing on incoming
X2-9
DSC call (see note 1)
X2-10
X2-11 Equipment ground
NMEA data input from external
X2-12
position sensor (see note 2)
X2-13
Relay contact closing on incoming
X2-14
Distress alert (see note 1)
X2-15
Out to CU2 or to alarm panel "VHF"
extension box connector X3
X5-1 X6-1
X5-2 X6-2 3
X5-3 X6-3 5
X5-4 X6-4
X5-5 X6-5
X5-6 X6-6 2
X5-7 X6-7 9
X5-8 X6-8
X5-9 X6-9
X5-10 X6-10
X5-11 X6-11
X5-12 X6-12
X5-13 X6-13
X5-14 X6-14
X5-15 X6-15
Chassis Chassis
X9-1
X9-2
Ships cable
8 twisted pairs or
overall screen
pair no. 1
pair no. 1
pair no. 2
pair no. 2
pair no. 3
pair no. 3
pair no. 4
pair no. 4
pair no. 5
pair no. 5
pair no. 8
pair no. 6
pair no. 6
pair no. 7
pair no. 7
Screen Screens
Signal description Ships cable
8 twisted pairs
overall screen
Power to CUs pair no. 8
pair no. 1
SPARC II-bus Data
pair no. 1
pair no. 2
SPARC II-bus Tx audio
pair no. 2
pair no. 6 & 8
Equipment ground
pair no. 6
Power to CUs
pair no. 3
SPARC II-bus Rx audio
pair no. 3
pair no. 7
Power to CUs
VHF radio external
pair no. 4
speaker output, nom. 5W
pair no. 4
into 8Ω
pair no. 7
Equipment ground
Rx-audio line output,
pair no. 5
balanced signal, 0dBm
into 600Ω pair no. 5
Screen
External speaker output,
nom. 5W into 8Ω (see
NOTE)
0611