Related Manuals for Aventura CAM-IPM-13X-DNPC
Summary of Contents for Aventura CAM-IPM-13X-DNPC
-
Page 1: Network Camera
Network Camera Installation Manual V4.0.1... - Page 2 Find the model of your camera in the following list. Then according to the structure Type on the left of your camera Model, you can find corresponding chapter for instructions of your camera. Type Model Box Camera I CAM-IPM-13X-DNPC, CAM-IPM-2X-DNP Box Camera II CAM-IPM-2X-DNPC CAM-IPM-3X-DNP Box camera III CAM-IP-5X-WDR...
-
Page 3: Safety Instruction
Installation Manual of Network Camera Safety Instruction These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. The precautionary measure is divided into ‘Warnings’ and ‘Cautions’: Warnings: Serious injury or death may be caused if any of these warnings are neglected. Cautions: Injury or equipment damage may be caused if any of these cautions are neglected. - Page 4 Installation Manual of Network Camera Cautions: Make sure the power supply voltage is correct before using the camera. Do not drop the camera or subject it to physical shock. Do not touch sensor modules with fingers. If cleaning is necessary, use a clean cloth with a bit of ethanol and wipe it gently.
-
Page 5: Table Of Contents
Installation Manual of Network Camera Table of Contents CHAPTER 1 INTRODUCTION ............................ 1 ................................1 PPLICATIONS ................................1 REPARATIONS CHAPTER 2 BOX CAMERA INSTALLATION ......................... 1 ............................1 PPEARANCE ESCRIPTION 2.1.1 Box Camera I ..............................1 2.1.2 Box Camera II ..............................3 2.1.3 Box Camera III .............................. -
Page 6: Chapter 1 Introduction
Installation Manual of Network Camera Chapter 1 Introduction The network camera is a kind of embedded digital surveillance product that combines the features of both a traditional analog camera and a net DVS (Digital Video Server). With a built-in video server, the network camera is capable of providing real-time video stream compression, processing, video analysis and transmission simultaneously. -
Page 7: Chapter 2 Box Camera Installation
Installation Manual of Network Camera Chapter 2 Box Camera Installation 2.1 Appearance Description 2.1.1 Box Camera I Camera description: Overview Figure 2-1 Description Table 2-1 Description CS Lens mount Back focus ring Auto-iris interface 10M/100M self-adaptive Ethernet interface AUDIO IN: Audio input interface AUDIO OUT: Audio output interface SD: SD card slot VIDEO OUT: Video output interface... - Page 8 Installation Manual of Network Camera Note: The type of auto-iris interface is shown in Figure 2-2, and the definition of each pin is shown below in Table 2-2: Auto-iris Interface Figure 2-2 Pins Table 2-2 Video-driven DC-driven Power Damp- Damp+ Video Drive+ Drive-...
-
Page 9: Box Camera Ii
Installation Manual of Network Camera 2.1.2 Box Camera II Camera description: Overview Figure 2-4 Overview Figure 2-5 Description Table 2-3 Description CS Lens mount Auto-iris interface Bracket mounting holes F1+ F1-, F2+ F2- ,F3+ F3-: Alarm output interface T1,T2,T3, T4,GND: Alarm input interface D+, D-: RS-485 interface 10M/100M self-adaptive Ethernet interface VIDEO OUT/HDMI: Video output interface... - Page 10 Installation Manual of Network Camera Power supply interface POWER: Power LED indicator SD: SD card slot AUDIO IN: Audio input interface AUDIO OUT: Audio output interface Ground Notes: After powering the camera on, pressing and holding the RESET button for about 10 seconds can reset all the parameters to the default settings.
-
Page 11: Box Camera Iii
Installation Manual of Network Camera Camera wiring Diagram: Wiring Diagram Figure 2-7 2.1.3 Box Camera III Camera description: Overview Figure 2-8... - Page 12 Installation Manual of Network Camera Description Table 2-5 Description Lens mount Back focus ring SD card slot Auto-iris interface 10M/100M self-adaptive Ethernet interface VIDEO OUT: Video output interface AUDIO OUT: Audio output interface POWER: Power LED indicator Power supply interface MIC IN: Audio input interface D+, D-: RS-485 interface IN, G: Alarm input interface...
- Page 13 Installation Manual of Network Camera Camera wiring Diagram: Wiring Diagram Figure 2-10...
-
Page 14: Installation
Installation Manual of Network Camera 2.2 Installation Box camera I, II, III can be installed to wall or ceiling. Ceiling mounting is taken as an example in this section; if you adopt wall mounting, you can also take the below procedure as a reference. Steps: 1. - Page 15 Installation Manual of Network Camera 2. Aim the screw hole on the camera at the bracket and rotate the camera tightly. Adjust the camera to the desired surveillance angle and tighten the knob on bracket to secure the camera. Mount the Camera Figure 2-12 3.
-
Page 16: Chapter 3 Dome Camera Installation
Installation Manual of Network Camera Chapter 3 Dome Camera Installation 3.1 Dome Camera I 3.1.1 Appearance Description Camera description: Overview Figure 3-1 Description Table 3-1 Description 10M/100M self-adaptive Ethernet interface AUDIO IN: Audio input interface AUDIO OUT: Audio output interface D+, D-: RS-485 interface IN, G: Alarm input interface 1A, 1B: Alarm output interface... - Page 17 Installation Manual of Network Camera Camera wiring Diagram: Wiring Diagram Figure 3-2...
-
Page 18: Installation
Installation Manual of Network Camera 3.1.2 Installation The ceiling mounting and wall mounting are available for dome camera II. For wall mounting, you need to use a special vandal-proof bracket. Steps: 1. Loosen the screw with the hex key (supplied) and remove the lower dome. Remove the Lower Dome Figure 3-3 2. - Page 19 Installation Manual of Network Camera Notes: For wall mounting, position the side cable outlet directly downward for water proofing. Downward Downward Wall Mounting Direction Figure 3-5 If you need to pull the cable through the cable outlet from the side of the camera, please use water-proof joints and water-proof pipe to route the cables.
- Page 20 Installation Manual of Network Camera 4. Tighten the screw after adjustment, and reinstall the lower dome to finish the installation. Reinstall the Lower Dome Figure 3-7...
-
Page 21: Dome Camera Ii
Installation Manual of Network Camera 3.2 Dome Camera II 3.2.1 Appearance Description Camera description: Overview Figure 3-8 Description Table 3-2 Description 10M/100M self-adaptive Ethernet interface INITIAL SET: Reset button AUDIO OUT: Audio output interface MIC IN: Audio input interface D+, D-: RS-485 interface 1A, 1B, 2A, 2B: Alarm output interface IN1, GND, IN2, GND: Alarm input interface Power supply interface... - Page 22 Installation Manual of Network Camera Camera wiring Diagram: Wiring Diagram Figure 3-9...
-
Page 23: Installation
Installation Manual of Network Camera 3.2.2 Installation Ceiling mounting: Note: If required, you can use a plier to remove the clip (one or two) on the side of the back box and then route cables through the opening to secure the cables on the ceiling. Clips Remove the Clip Figure 3-10... - Page 24 Installation Manual of Network Camera 2. Loosen the set screws with the hex key (supplied) to remove the lower dome. Remove the Lower Dome Figure 3-12 3. Connect the RCA analog video output with a monitor to view the image of the camera. Loosen the lens set screw and pan, tilt or rotate the lens to get a desired surveillance angle.
- Page 25 Installation Manual of Network Camera 4. Reinstall the lower dome and tighten the screws. Reinstall the Lower Dome Figure 3-14 In-ceiling mounting: Steps: 1. Secure the mounting base to the in-ceiling mounting base with screws. In-ceiling mounting base Mounting base Secure the Mounting Base Figure 3-15 Figure 3-16...
- Page 26 Installation Manual of Network Camera 2. Push the dome camera to the in-ceiling mounting base, rotate the dome camera for 10 degrees counterclockwise and then fasten the lock screws to fix the camera. ③ Lock screw ① ② Fix the Camera Figure 3-17 3.
- Page 27 Installation Manual of Network Camera 4. It is strongly recommended that you use a safety rope to secure the in-ceiling mounting base to the roof. Safety rope Safety rope Figure 3-19 5. Fasten the lock screws to secure the dome camera. Lock screw Secure the Camera Figure 3-20...
- Page 28 Installation Manual of Network Camera Adjust the Image Figure 3-21 7. Install the trim plate with screws to finish the installation. Reinstall the Lower Dome Figure 3-22...
-
Page 29: Chapter 4 Bullet Camera Installation
Installation Manual of Network Camera Chapter 4 Bullet Camera Installation 4.1 Appearance Description Camera description: Overview Figure 4-1 Overview Figure 4-2 Description Table 4-1 Description 10M/100M self-adaptive Ethernet interface Power supply interface IN, G: Alarm input interface 1A, 1B: Alarm output interface D+, D-: RS-485 interface AUDIO IN, G: Audio input interface AUDIO OUT, G: Audio output interface... - Page 30 Installation Manual of Network Camera Camera wiring Diagram: Wiring Diagram Figure 4-3...
-
Page 31: I Nstallation
Installation Manual of Network Camera 4.2 Installation Bullet camera can be installed to wall or ceiling. Wall mounting is taken as an example in this section; if you adopt ceiling mounting, you can also take below procedure as a reference. Steps: 1. - Page 32 Installation Manual of Network Camera 2. Attach the mounting bracket with the camera to the mounting base with the safety rope (not shown in the figure below). Fix the mounting bracket with the camera to the mounting base with screws. Note: The “bottom”...
- Page 33 Installation Manual of Network Camera 6. Loosen the lock screw on the sun shield and move the sun shield until you can remove it. Remove the sun shield. Remove the Sun Shield Figure 4-7 7. Rotate to remove the front cover from camera and adjust the lens to get a clear image. Adjust the lens Front cover Adjust the Lens...
-
Page 34: Appearance Description
Installation Manual of Network Camera Chapter 5 Mini Dome Camera Installation 5.1 Appearance Description Camera description: Overview Figure 5-1 Description Table 5-1 Description Cover Lens P: Power LED indicator, It is solid red when power is applied to the unit. Base plate Set screw hole Set screw of lens... - Page 35 Installation Manual of Network Camera Camera wiring Diagram: Wiring Diagram Figure 5-2...
-
Page 36: Installation
Installation Manual of Network Camera 5.2 Installation The ceiling mounting is recommended for this camera. Note: If required, you can use a plier to remove the clip on the side of the back box and then route cables through the opening to secure the cables on the ceiling. Clip Remove the Clip Figure 5-3... - Page 37 Installation Manual of Network Camera 2. Use the screws to fix the base plate on the ceiling. Fix the Base Plate Figure 5-5 3. View the video image of the camera over the network. 4. Loosen the lens set screws. Loosen the lens set screws.
- Page 38 Installation Manual of Network Camera 5. Insert the hex key into the hole marked in the Figure 5-7 and rotate the hex key to adjust the panning position and tilting position until getting the desired surveillance angle. Tighten the set screws.
- Page 39 Installation Manual of Network Camera 6. Reinstall the cover, and tighten the set screws. Reinstall Figure 5-8 Reinstall Figure 5-9...
Need help?
Do you have a question about the CAM-IPM-13X-DNPC and is the answer not in the manual?
Questions and answers